Kohler K-T13133 Bedienungsanleitung

Installation Guide

Single-Control Bath and Shower Trim

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-T13133 K-T13134

K-T13135 K-13136

K-13139

1036140-2-A

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

•Do not install a shut-off device on either outlet of this valve. The

installation of any such device may create a cross-ﬂow condition

at the valve and affect the water temperature.

•Factors that change the temperature of the water supplied to the

valve, such as seasonal water temperature changes, and water

heater replacement or servicing, will change the maximum water

temperature supplied by the valve and may create a scalding

hazard.

•The pressure-balanced valve will not compensate for changes in

the water supply temperature; adjust the maximum water

temperature setting of this pressure-balanced valve when such

changes occur.

•Pressure-balanced valves may not provide protection against

scalding if there is a failure of other temperature-limiting devices

elsewhere in the plumbing system.

The installer is responsible for installing the valve and adjusting the

maximum water temperature of this pressure-balanced valve

according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the installation or temperature

adjustment instructions in this document, in the United States please

contact our Customer Service Department at 1-800-4-KOHLER.

Outside the U.S., please contact your distributor.

IMPORTANT NOTICE TO INSTALLERS! Please ﬁll in the blanks in

the information box in the Homeowners Guide and on the valve label.

Retain the Homeowners Guide for future reference.

1036140-2-A 2 Kohler Co.

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and web site are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

CAUTION: Risk of product damage to the K-306-KS valve

assembly. When using this valve in a ﬁberglass or acrylic

installation, use the Thin Wall Installation Kit (88526).

Observe all local plumbing and building codes.

Before installation, unpack the new faucet and inspect it for

damage. Return the faucet to the carton until you are ready to

install it.

The ﬁnished wall or bath/shower unit must be installed prior to

installing this trim.

We recommend that you determine if the maximum water

temperature is acceptable prior to installing this trim. If

temperature adjustment is needed, refer to the “Adjust the Water

Temperature” section.

The valve shuts off by water pressure. Do not force the handle in

any direction. To turn the valve off, gently turn it to the “Off”

position.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Strap

Wrench Thread

Sealant Plumbers

Putty

Hex

Wrench

Kohler Co. 3 1036140-2-A

1. Install the Spout, If Used

Remove the temporary nipple.

Apply thread sealant and install a 1/2″nipple so it extends 7/16″

(1.1 cm) beyond the ﬁnished wall.

Apply a bead of plumbers putty or other sealant around the back

of the escutcheon according to the manufacturer’s instructions.

Apply thread sealant to the nipple and thread the spout onto the

nipple.

Carefully tighten with a clean strap wrench.

Remove all excess putty.

Spout

Bath

Elbow Escutcheon

Apply Thread

Sealant Tape.

Apply

Plumbers

Putty.

7/16"

(1.1 cm)

1/2" Nipple

1036140-2-A 4 Kohler Co.

2. Install the Showerhead, If Used

CAUTION: Risk of product damage. To avoid plugging the

showerhead spray outlets, use thread sealant tape on the shower

arm threads. Do not use thread sealant compound (pipe dope).

Remove the temporary nipple from the shower elbow.

Apply a bead of plumbers putty or other sealant to the back of

the bonnet according to the manufacturer’s instructions.

Slide the bonnet onto the shower arm.

Apply thread sealant tape to the threads and install the shower

arm to the shower elbow.

Carefully tighten with a clean strap wrench.

Press the bonnet and escutcheon against the wall and secure to

the shower arm by tightening the setscrew.

Remove all excess putty.

With the showerhead off, ﬂush out the system.

Ensure that the screen is positioned as shown on the showerhead.

Apply thread sealant tape to the shower arm and thread the

showerhead to the shower arm.

Use a clean strap wrench to tighten the showerhead.

Check for proper operation.

Bonnet

Shower

Elbow

Escutcheon

Shower Arm

Screen

Showerhead

Apply Thread

Sealant Tape.

Apply

Plumbers

Putty.

Kohler Co. 5 1036140-2-A

3. Water Temperature Adjustment

CAUTION: Risk of personal injury. The water temperature

should never be set above 120° F (49° C).

NOTE: Do not remove the O-ring and collar at this time. Removing

the O-ring and collar will change the factory setting for the

maximum water temperature.

Turn the valve clockwise to the full open position and let the hot

water run for several minutes. Position a thermometer in the

water stream and check the temperature.

For minor water temperature changes, adjust the setscrew, and

recheck the water temperature.

For major water temperature changes, remove the O-ring and

collar from the valve stem. Slowly rotate the valve stem until the

desired maximum water temperature is reached.

Reinstall the collar on the valve stem with the setscrew against

the side of the tab.

Reinstall the O-ring, rotate the valve stem counterclockwise to

shut the water off.

Recheck the water temperature to ensure desired maximum water

temperature.

NOTE: After adjustment, complete the required information on the

valve label (if supplied).

O-Ring

Setscrew

Tab

Collar

Setscrew

Valve

Label

Standard

Valve

High Flow

Valve

Stem

1036140-2-A 6 Kohler Co.

4. Install the Plate and Diverter

Remove and discard the plaster guard and/or dome, if installed.

For installation over a tiled wall, apply a bead of silicone sealant

around the back edges of the faceplate.

Fit the backing plate over the valve so the large hole is to the

bottom and secure with two screws. Do not overtighten.

Position the gasket over the diverter stem.

Position the stem adapter over the diverter stem and tighten the

setscrew.

Slide the sleeve over the stem adapter and thread onto the

diverter threads.

Screw

Discard.

Backing Plate

Plaster Guard

w/Dome

Valve

Diverter

Stem

Setscrew

Gasket

Sleeve

Valve Stem

Stem

Adapter

Kohler Co. 7 1036140-2-A

5. Install the Escutcheon and Sleeve

Remove and discard the plaster guard and/or dome, if installed.

For installation over a tiled wall, apply a bead of silicone sealant

around the back edges of the escutcheon.

Rotate the valve stem fully counterclockwise.

Position the escutcheon over the valve, and thread the collar into

the backing plate. Do not cross thread.

Insert the sleeve tabs into the collar notches and hand tighten.

Remove the sleeve from the collar, and turn it around so the tabs

face outward.

Insert the sleeve into the collar so the slot is down and facing

outward.

Valve Stem

Plaster Guard

w/Dome Discard.

Collar

Plate

Escutcheon

Sleeve

Collar

Escutcheon

Sleeve

1036140-2-A 8 Kohler Co.

6. Complete the Installation

Turn the sleeve as needed so the notch lines up with the bonnet

assembly setscrew.

Install the bonnet on the sleeve and tighten the setscrew.

Place the spline adaptor on the bonnet stem.

Place the handle on the spline adaptor.

Secure the handle in place by tightening the screw.

Align the tab on the plug button with the notch in the handle and

insert the plug button with O-ring in the handle.

If applicable, thread the diverter knob onto the diverter actuator.

O-Ring

Handle

Spline Adapter

Diverter Knob

Bonnet

Setscrew Screw

Plug Button

Kohler Co. 9 1036140-2-A

Guide d’installation

Garniture robinet mono-contrôle de baignoire

et douche

INSTRUCTIONS

IMPORTANTES

À LIRE ET À LAISSER AU CLIENT

AVERTISSEMENT : Risque de brûlures ou de blessures graves.

•Avant de commencer l’installation, l’installateur doit régler la

température maximale de l’eau de cette valve pour réduire au

minimum les risques de brûlures, ceci conformément à la norme

ASTM F 444.

•Ne pas installer un dispositif d’arrêt sur les sorties de cette valve.

L’installation d’un tel dispositif peut créer une condition

d’écoulement croisé au régulateur et modiﬁer la température de

l’eau.

•Les facteurs qui changent la température de l’eau fournie à cette

valve, tels que les changements des saisons et la température de

d’eau, et le remplacement ou l’entretien du chauffeau, changeront

la température maximale de l’eau fournie par le régulateur et

pourront présenter un danger de brûlures.

•La valve à pression équilibrée ne compensera pas pour les

changements de température d’eau fournie; ajuster la température

maximale de cette valve à pression équilibrée si de tels

changements se produisent.

•Les valves à pression équilibrée peuvent ne pas assurer une

protection contre les brûlures en cas de défaillance d’autres

dispositifs de limitation de température installés ailleurs sur le

réseau de plomberie.

L’installateur est responsable de l’installation de la valve et du

réglage de la température maximale de l’eau de cette valve à pression

équilibrée conformément aux instructions.

Cette valve satisfait ou excède les exigences des normes ANSI

A112.18.1M et ASSE 1016.

Kohler Co. Français-1 1036140-2-A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-26228T Bedienungsanleitung

Kohler

Kohler FAMILY CARE Bedienungsanleitung

Kohler

Kohler K-3593-L Bedienungsanleitung

Kohler

Kohler K-19909-4 Montageanleitung

Kohler

Kohler 72419IN Bedienungsanleitung

Kohler

Kohler K-11340X Montageanleitung

Kohler

Kohler Purist K-T14428 Bedienungsanleitung

Kohler

Kohler AVID 31137T-4 Bedienungsanleitung

Kohler

Kohler K-T10274 Montageanleitung

Kohler

Kohler K-2098 Montageanleitung

Kohler

Kohler ODEON 98963M-4 Bedienungsanleitung

Kohler

Kohler Stillness K-14450 Bedienungsanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler K-454 Montageanleitung

Kohler

Kohler Mira Atom ERD Bedienungsanleitung

Kohler

Kohler K-9677 Montageanleitung

Kohler

Kohler k-2815 Bedienungsanleitung

Kohler

Kohler ALEO Bedienungsanleitung

Kohler

Kohler K-15886 Montageanleitung

Kohler

Kohler Quiet-Close C3-455 Bedienungsanleitung

Kohler

Kohler K-13711 Bedienungsanleitung

Kohler

Kohler K-6536 Bedienungsanleitung

Kohler

Kohler 76633T-B Bedienungsanleitung

Kohler

Kohler K-T195 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung