Kohler Purist K-T14428 Bedienungsanleitung

Installation Guide

Purist™

Bath/Deck Mount Faucet

Mproduct numbers are for Mexico (i.e.

K-12345M)

Los números de productos seguidos de M

corresponden a México (e.j. K-12345M)

Français, page “Français-1”

Español, pagina “Español-1”

K-T14428, K-T14428M K-T14429, K-T14429M

K-14430, K-14430M

1016271-2-A

Tools and Materials

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few minutes

to review this manual before you start installation. If you encounter any

installation or performance problems, please don’t hesitate to contact us. Our

phone numbers and web site are listed on the back cover. Thanks again for

choosing Kohler Company.

Before You Begin

Please read all instructions before you begin.

Observe all local plumbing and building codes.

Before installation, unpack the new faucet and inspect it for damage. Return

the faucet to the carton until you are ready to install.

Leave the protective sleeve on the spout supply tube until the spout is

installed. The spout has an O-ring sealing surface which may be damaged if

unprotected.

Provide an access panel to the valves from under the deck.

Installer-supplied copper tubing is to be 5/8” O.D. (1/2” nominal).

Install water hammer arrestors in the supply lines near the valves.

These instructions cover two methods of installation; installation on ﬁnished

deck or rim, and installation on rough (unﬁnished) deck. Follow the sections

that pertain to your particular installation.

Instructions are given for installations with 8” (20.3cm) centers. For wider

installations, adjust all roughing-in dimensions and copper tubing lengths

accordingly.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of faucets

without notice, as speciﬁed in the Price Book.

Adjustable

Wrench

SolderPropane

Torch

Assorted

Screwdrivers

Pipe

Wrench Strap

Wrench Hacksawor

TubingCutter

Plumbers

PuttyThread

Sealant

1016271-2-A 2 Kohler Co.

1. Prepare the Site

Install or relocate the water supplies as needed.

Protect the surfaces of the bath/deck during installation.

The diameter of the spout hole in the deck is 1” (2.5cm). The diameter of

the valve hole in the deck is 1–1/2” (3.8cm). Ensure that holes drilled into

the deck are not oversized. The spout and valves require adequate base

material strength and maximum contact area with the deck.

Plaster guard diameters are approximately 1–5/8” (4.1cm) for the valves

and 13/16” (2.1cm) for the spout.

NOTE: Reinforcing material may be required if the deck or rim is thin.

Install before proceeding.

NOTE: For installations to be covered with tile, the tile thickness must not

exceed 1–1/4” (3.2cm).

3-1/2” (8.9cm)

7/8” D.

(2.2cm)

2-1/2” (6.4cm)

1-5/16” D.

(3.3cm)

8” (20.3cm) Min.

2-1/8” (5.4cm) MAX.

ROUGH DECK

3/4”

I.D.

11-3/8”

(28.9cm)

7-1/2”

(19.1cm)

1/4” (6mm)

TO1-1/4”

(3.2cm) MAX.

FINISHED

DECK

ROUGH +

FINISHED

DECK MOUNT

INSTALLATION

RIMDECK

MOUNT

INSTALLATION

1-3/8”

(3.5cm)

2-5/8”

(6.7cm)

4-3/4”

(12.1cm)

1/4” (6mm) TO

2-1/8” (5.4cm)

MAX.RIMOR

DECK MOUNT

4-3/4”

(12.1cm)

2-1/2” D.(6.4cm)

CROSS 2-1/2” D.(6.4cm)

LEVER

7-3/4”

(19.7cm)

Kohler Co. 3 1016271-2-A

2. Installation on Finished Deck or Rim

NOTE: For installation on a rough (unﬁnished) deck, proceed to Installation

on Rough (Unﬁnished) Deck.

Use 1/2” nominal, 5/8” O.D. copper tubing. Cut two pieces of tubing to a

length of 2–7/8” (7.3cm). Cut one piece of tubing to a length of 2–3/8”

(6cm) for the spout supply.

IMPORTANT! Leave the protective sleeve on the spout supply tube until

the spout is installed to protect the O-ring sealing surface.

Install Spout Supply Tube

Slide a brass washer from the bottom of the spout supply tube over the

threads until the washer reaches the supply tube shoulder.

Insert the spout supply tube through the mounting hole from the top of the

deck/rim. Ensure that the ﬂat portion of the washer faces forward. The

supply tube will be suspended by the washer.

Slide a brass washer onto the spout supply tube from the bottom and

thread the mounting nut. Tighten the nut.

NOTE: Do not use the supplied wood screws for installation on ﬁnished

deck or rim.

Install Valve Bodies

Thread one mounting nut, ﬂange side up, onto each valve body.

NOTE: Rims less than 1/4” (6mm) thick require two rubber washers in the

following step; other installations require one rubber washer.

1” (2.5cm)

Collar

HotSupply

Cold

Supply

Solder2-7/8” (7.3cm)

CopperTubes

ValveBody

Mounting Nut

FiberWasher

RubberWasher

or Washers

Spout SupplyTube

SupplyTubeShoulder

Brass Washers

Nut

Solder

2–3/8” (6cm)

CopperTube

1/2” (1.3cm)

Tee

Solder

1016271-2-A 4 Kohler Co.

Installation on Finished Deck or Rim (cont.)

Slide one ﬁber washer, followed by one or two rubber washers, onto each

valve body.

Insert the 2–7/8” (7.3cm) long copper tubes between the valve bodies and

the 1/2” tee. Insert the 2–3/8” (6cm) long copper tube into the top of the

tee.

Do not solder the connections at this time.

NOTE: The valve body marked “Cold” must be on the right side when you

are facing the front of the faucet.

Insert the valve bodies through the mounting holes from the bottom of the

deck/rim. Match the copper tube from the tee with the spout supply tube.

Hold in place.

Place a collar with the ﬂange side up, onto each valve body. Thread the

collar down to at least 1” (2.5cm) from the top thread on the valve body.

Tighten the mounting nuts on each valve body from underneath the

deck/rim.

Solder the copper tubes to the valve bodies, tee and spout supply tube.

Solder the hot and cold water tubes to the valve body inlets. Ensure that the

cold supply is on the right side.

Proceed to Check Operation of Valves.

Kohler Co. 5 1016271-2-A

3. Installation on Rough (Unﬁnished) Deck

Use 1/2” nominal, 5/8” O.D. copper tubing. Cut two pieces of tubing to a

length of 2–7/8” (7.3cm). Cut one piece of tubing to a length of 2–3/8”

(6cm) for the spout supply.

IMPORTANT! Leave the protective sleeve on the spout supply tube until

the spout is installed to protect the O-ring sealing surface.

Install Spout Supply Tube

Slide a brass washer from the bottom of the spout supply tube over the

threads until the washer reaches the supply tube shoulder. Ensure that the

countersunk holes in the washer are facing upward.

Insert the spout supply tube through the mounting hole from the top of the

deck. Ensure that the ﬂat portion of the washer faces forward. The supply

tube will be suspended by the washer.

Slide a brass washer onto the spout supply tube from the bottom and

thread the mounting nut. Tighten the nut.

Secure the brass washer to the deck using the two supplied wood screws.

Install Valve Bodies

Thread one mounting nut, ﬂange side up, followed by one ﬁber washer and

one rubber washer onto each valve body.

Insert the 2–7/8” (7.3cm) long copper tubes between the valve bodies and

the 1/2” tee.

Do not solder the connections at this time.

1” (2.5cm)

Collar

HotSupply

Cold

Supply

Solder2-7/8” (7.3cm)

CopperTubes

ValveBody

Mounting Nut

FiberWasher

RubberWasher

or Washers

Spout SupplyTube

SupplyTubeShoulder

Brass Washers

Nut

Solder

2–3/8” (6cm)

CopperTube

1/2” (1.3cm)

Tee

Solder

Screw

1016271-2-A 6 Kohler Co.

Installation on Rough (Unﬁnished) Deck (cont.)

NOTE: The valve body marked “Cold” must be on the right side when you

are facing the front of the faucet.

Insert the valve bodies through the mounting holes from the bottom of the

deck. Match the copper tube from the tee with the spout supply tube. Hold

in place.

Place a collar with the ﬂange side up, onto each valve body. Thread the

collar down to at least 1” (2.5cm) from the top thread on the valve body.

Kohler Co. 7 1016271-2-A

4. Complete Installation on Rough Deck

Set Valve Body Height

NOTE: Use one of the following two formulas to calculate the valve body

clearance required for the ﬁnish material at your site.

For tile that is less than 1” (2.5cm) thick, add 1–1/4” (3.2cm) to the tile

thickness. Example: Tile thickness is 3/4” + 1–1/4” = 2” (5cm) of clearance

required.

For tile that is between 1” (2.5cm) and 1–1/4” (3.2cm) thick, add only 1”

(2.5cm) to the tile thickness. Example: Tile thickness is 1–1/4” + 1” = 2–1/4”

(5.7cm).

Adjust the threaded collar until the dimension from the top of the valve

threads to the top of the rough deck equals the clearance requirement

needed. Make a note of this dimension. You will use it again after

connecting the supply tube.

Connect Supply Tube

Measure the distance from the bottom of the spout supply tube to the top of

the tee.

Add 1” (2.5cm) to this measurement and cut a piece of copper tubing to ﬁt

into the supply tube and tee port.

Fully loosen the threaded collars but do not remove them.

Pivot the valve bodies enough to remove the tee and two pieces of tubing.

If the valve body holes are smaller than recommended, it may be necessary

to remove the entire valve body assembly.

Install the tubing into the tee. Match the copper tube from the tee with the

spout supply tube.

2-1/8”

(5.4cm)

Max.

2”

(5cm)

1-1/4”(3.2cm)

Top ofValve

Threads

3/4”(2cm)

Threaded

Collar

Rough

Deck

Tile

Spout

Supply

Tube

Solder

Tee

Copper

Tube

Hot

SupplyCold

Supply

Valve BodyMounting

Nut

1016271-2-A 8 Kohler Co.

Complete Installation on Rough Deck (cont.)

Pivot the valve bodies onto the two pieces of copper tubing.

Do not solder at this time.

Reset Valve Body Height

Adjust the threaded collars until the dimension from the top of the valve

threads to the top of the rough deck equals the clearance requirement

calculated earlier.

Solder Connections

Tighten the mounting nuts on each valve body under the deck.

Solder the copper tubes to the valve bodies, tee and spout supply tube.

Ensure that the cold supply is on the right side.

Solder the hot and cold water supply tubes to the valve body inlets.

Kohler Co. 9 1016271-2-A

5. Check Operation of Valves

Thread a 1/4” pipe plug into the top of the spout supply tube.

Ensure that the valves are closed (cold — fully counterclockwise; hot —

fully clockwise).

Turn on the main water supply and check the complete installation for leaks

with the valves closed and open. Repair leaks as needed.

Close both valves and turn off the main water supply.

WARNING: Risk of personal injury. Lines will be pressurized. Do not

lean over pipe plug as you remove it.

Wrap a towel around the pipe plug to prevent water spray. Water will

purge from the supply tube when you remove the plug.

Carefully loosen the pipe plug to remove pressure.

Thread the pipe plug back into the spout supply tube. Leave the pipe plug

installed until the spout and handles are installed.

Install the cardboard plaster guards over both valves and the spout supply

tube. Leave in place until the spout and handles are installed.

6. Install Tile (If Applicable)

Verify that there will be a 1–1/4” (3.2cm) distance from the top of the sleeve

to the top of the tile. If there is not, correct the valve clearance as described

earlier.

Install tile up to the plaster guards on the valves and the spout supply tube.

1/4” Pipe Plug Close

Cold

Hot

1016271-2-A 10 Kohler Co.

Andere Handbücher für Purist K-T14428

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler MINIMA K-45803T-L-SHP Bedienungsanleitung

Kohler

Kohler K-72218 Bedienungsanleitung

Kohler

Kohler 114753-2-CD Bedienungsanleitung

Kohler

Kohler K-18485 Montageanleitung

Kohler

Kohler SIMPLICE 596T-4E Bedienungsanleitung

Kohler

Kohler K-7223 Montageanleitung

Kohler

Kohler K-7127 Bedienungsanleitung

Kohler

Kohler K-6268 Montageanleitung

Kohler

Kohler PURIST UPGRADE Bedienungsanleitung

Kohler

Kohler K-2268 Montageanleitung

Kohler

Kohler 32E Bedienungsanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler K-7273-AF Montageanleitung

Kohler

Kohler Stargaze BubbleMassage K-1959-GHW Bedienungsanleitung

Kohler

Kohler K-11550 Bedienungsanleitung

Kohler

Kohler K-15261 Montageanleitung

Kohler

Kohler K-77963-8A-BL Bedienungsanleitung

Kohler

Kohler K-2191 Bedienungsanleitung

Kohler

Kohler Mira Azora Bedienungsanleitung

Kohler

Kohler K-6354 Bedienungsanleitung

Kohler

Kohler 3867T Bedienungsanleitung

Kohler

Kohler K-12286-4 Montageanleitung

Kohler

Kohler BADRON K-5487T-B Bedienungsanleitung

Kohler

Kohler K-19896 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung