Kohler Mira Honesty Bedienungsanleitung

11333238-W2-A

Installation and User Guide

These instructions must be left with the user

ERD Bar Valve and Fittings

Mira Honesty

1333238-W2-A

31333238-W2-A

Introduction

Thank you for choosing a Mira shower. To enjoy the full potential of

your new shower, please take time to read this guide thoroughly, and

keep it handy for future reference.

Guarantee

Recommended Usage

For domestic installations, Mira Showers guarantee this product

against any defect in materials or workmanship for a period of ve

years from the date of purchase (shower ttings for one year).

For non-domestic installations, Mira Showers guarantee this

product against any defect in materials or workmanship for a period

of one year from the date of purchase.

Failure to follow the instructions provided with the shower will

invalidate the guarantee.

For Terms and Conditions refer to the 'Customer Service'.

Domestic 

Light Commercial 

Heavy Commercial 

Healthcare 

Design Registration

Design Registration Number 005259041-0006-0007

1333238-W2-A

Pack Contents

1 x Bar Valve

2 x Wall Brackets

2 x Concealing Plates

2 x Compression Nuts

2 x Olives

2 x Washers/Filters

2 x Wall Plugs

2 x Fixing Screws

2 x Wall Plugs

1 x Wall Fixing Bracket

2 x Fixing Screws

1 x Grubscrew

1 x Riser Arm

1 x Concealing

Cover

1 x Handset

1 x Retaining

Ring

1 x Clamp Bracket

1 x Hose

2 x Hose Washer

1 x Lower Bar

1 x Middle Bar

1 x Overhead

Shower

1 x Valve Component Pack

(Packed with valve)

1 x Pipe Guide

51333238-W2-A

Safety Information

WARNING - This product can deliver scalding temperatures if

not operated, installed or maintained in accordance with the

instructions, warnings and cautions contained in this guide.

The function of a thermostatic mixing valve is to deliver water

consistently at a safe temperature. In keeping with every other

mechanism, it cannot be considered as functionally infallible and

as such, cannot totally replace a supervisor’s vigilance where that

is necessary. Provided it is installed, commissioned, operated and

maintained within manufacturers recommendations, the risk of

failure, if not eliminated, is reduced to the minimum achievable.

PLEASE OBSERVE THE FOLLOWING TO REDUCE THE RISK OF

INJURY:

INSTALLING THE SHOWER

1. Installation of the shower must be carried out in accordance with

these instructions by qualied, competent personnel. Read all

instructions before installing the shower.

2. DO NOT install the shower where it may be exposed to freezing

conditions. Ensure that any pipework that could become frozen

is properly insulated.

3. DO NOT perform any unspecied modications, drill or cut holes

in the shower or ttings other than instructed by this guide. When

servicing only use genuine Kohler Mira replacement parts.

4. If the shower is dismantled during installation or servicing then,

upon completion, an inspection must be made to ensure all

connections are tight and that there are no leaks.

USING THE SHOWER

1. The shower must be operated and maintained in accordance with

the requirements of this guide. Make sure you fully understand

how to operate the shower before use, read all instructions and

retain this guide for future reference.

2. DO NOT switch the shower on if there is a possibility that the water

in the shower unit or ttings is frozen.

1333238-W2-A

3. The shower can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved. Children must not

be allowed to play with the shower.

4. Anyone who may have di󰀩culty understanding or operating the

controls of any shower should be attended whilst showering.

Particular consideration should be given to the young, the elderly,

the inrm or anyone inexperienced in the correct operation of the

controls.

5. DO NOT allow children to clean or perform any user maintenance

to the shower unit without supervision.

6. Always check the water temperature is safe before entering the

shower.

7. Use caution when altering the water temperature while in use,

always check the temperature before continuing to shower.

8. DO NOT t any form of outlet ow control. Only Mira recommended

outlet ttings should be used.

9. DO NOT operate the temperature control rapidly, allow 10-15

seconds for the temperature to stabilise before use.

10. Use caution when altering the water temperature while in use,

always check the temperature before continuing to shower.

11. DO NOT switch the shower o󰀨 and back on while standing in the

water ow.

12. DO NOT connect the outlet of the shower to any tap, control valve,

trigger handset or showerhead other than those specied for use

with this shower. Only Kohler Mira recommended accessories

must be used.

13. The showerhead must be descaled regularly. Any blockage of the

showerhead or hose may a󰀨ect showering performance.

71333238-W2-A

Specication

• Max Static Pressure: 10 Bar.

• Max Maintained Pressure: 5 Bar.

• Min Maintained Pressure: (Gas Water Heater): 1.0 Bar (for

optimum performance supplies should be nominally equal).

• Min Maintained Pressure (Gravity System): 0.1 Bar (0.1 bar =

1 Metre head from cold tank base to shower handset outlet).

Pressures

• Close temperature control is provided between 20°C and 50°C.

• Optimum Thermostatic Control Range: 35°C to 45°C (achieved

with supplies of 15°C cold, 65°C hot and nominally equal

pressures).

• Recommended Hot Supply: 60°C to 65°C (Note! The mixing

valve can operate at temperatures up to 85°C for short periods

without damage. However for safety reasons it is recommended

that the maximum hot water temperature is limited to 65°C).

• Minimum Recommended Di󰀨erential between Hot Supply and

Outlet Temperature: 12°C at desired ow rates.

• Minimum hot water supply temperature: 55°C.

Temperatures

• For safety and comfort the thermostat will shut o󰀨 the mixing

valve within 2 Seconds if either supply fails (achieved only if

the blend temperature has a minimum di󰀨erential of 12°C from

either supply temperature).

Thermostatic Shut-down

Connections

• Hot: Left - 15mm pipework, 3/4” BSP to valve.

• Cold: Right - 15mm to pipework, 3/4” BSP to valve.

• Outlet: Bottom - 1/2” BSP Male to exible hose.

Note! This product does not allow for reversed inlets and will

deliver unstable temperatures if tted incorrectly.

1333238-W2-A

Installation

Suitable Plumbing Systems

Gravity Fed:

The thermostatic mixer must be fed from a cold water cistern (usually tted in the

loft space) and a hot water cylinder (usually tted in the airing cupboard) providing

nominally equal pressures.

Gas Heated System:

The thermostatic mixer can be installed with a combination boiler.

Unvented Mains Pressure System:

The thermostatic mixer can be installed with an unvented, stored hot water system.

Mains Pressurised Instantaneous Hot Water System:

The thermostatic mixer can be installed with systems of this type with balanced

pressures.

Pumped System:

The thermostatic mixer can be installed with an inlet pump (twin impeller). The

pump must be installed on the oor next to the hot water cylinder.

General

1. Installation of the shower must be carried out in accordance with these

instructions by qualied, competent personnel.

2. The plumbing installation must comply with all national or local water regulations

and all relevant building regulations, or any particular regulation or practice

specied by the local water supply company.

3. Make sure all pressures and temperatures comply with the requirements of the

shower. See ‘Specications’.

4. Full bore / non restrictive isolating valves must be tted in a readily accessible

position adjacent to the shower to facilitate maintenance of the shower.

DO NOT use a valve with a loose washer plate (jumper) as this can lead to a

build up of static pressure.

5. Use copper pipe for all plumbing.

6. DO NOT apply excessive force to plumbing connections; always provide

mechanical support when making plumbing connections. Any soldered joints

should be made before connecting the shower. Pipework must be rigidly

supported and avoid any strain on the connections.

7. Pipework dead-legs should be kept to a minimum.

91333238-W2-A

10. Only use the inlet connections supplied with the product. DO NOT use any

other type of ttings.

11. DO NOT overtighten connections, screws or grubscrews as product damage

may occur.

8. Position the shower unit where the controls are at a convenient height for the

user. Position the showerhead so that the water sprays in line with the bath or

across the opening of a shower cubicle. The installation must not cause the

shower hose to be kinked during normal use or obstruct the use of the control

handles.

9. The position of the shower unit and hose retaining ring must provide a minimum

air gap of 25 mm between the showerhead and the spill over level of any bath,

shower tray or basin. There must be a minimum distance of 30 mm between

the showerhead and the spill over lever of any toilet, bidet or other appliance

with a Fluid Category 5 backow risk.

Note! There will be occasions when the hose retaining ring will not provide a

suitable solution for Fluid Category 3 installations, in these instances an outlet

double checkvalve must be tted, this will increase the required supply pressure

typically by 10kPa (0.1 bar). Double checkvalves tted in the inlet supply to

the appliance cause a pressure build up, which a󰀨ect the maximum static inlet

pressure for the appliance and must not be tted. For Fluid category 5 double

checkvalves are not suitable.

Zone of

Backow

Risk

30 mm

Minimum

Toilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Mixer

Shower

25 mm

Minimum

25 mm Minimum

1333238-W2-A

Wall Bracket

Make sure that the pipework has been

installed correctly and that it protrudes

25 mm from the nished wall surface.

Hold the wall bracket in position and

mark the position of the xing holes.

Drill the xing holes using an 8 mm

diameter drill.

Fit the plastic pipe guide over the inlet

pipes. Level the pipe guide and secure

to the wall to hold in position. Leave the

guide in place and nish the wall.

Installation of the Bar Valve Fast Fix Kit

Before installing the pipework, please ensure that there is a minimum of 1260 mm

height clearance to allow for the rigid riser and overhead to be installed above. If

installing in a restricted height area, a shorter riser rail can be ordered as a spare part.

25 mm

150 mm

25 mm

8 mm

Plastic Pipe

Guide

HOT

COLD

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13132-3A Montageanleitung

Kohler

Kohler MEMOIRS K-2258 Montageanleitung

Kohler

Kohler Antique K-100 Montageanleitung

Kohler

Kohler Modernlife Touchless 77786K-TF-0 Bedienungsanleitung

Kohler

Kohler K-12177 Bedienungsanleitung

Kohler

Kohler K-1110 Kurzanleitung

Kohler

Kohler C3-150 Bedienungsanleitung

Kohler

Kohler K-10349 Montageanleitung

Kohler

Kohler Wave 12791T-4 Bedienungsanleitung

Kohler

Kohler 77984T-4MU Bedienungsanleitung

Kohler

Kohler 8030A Bedienungsanleitung

Kohler

Kohler 17493W-CP Bedienungsanleitung

Kohler

Kohler RiverBath Quadrangle K-1365-F2 Bedienungsanleitung

Kohler

Kohler Sunstruck K-1967-GHW Bedienungsanleitung

Kohler

Kohler STRAYT 37337T-B4 Bedienungsanleitung

Kohler

Kohler PureFlo K-37388 Montageanleitung

Kohler

Kohler K-2276 Bedienungsanleitung

Kohler

Kohler K-19950 Montageanleitung

Kohler

Kohler Discovery Bedienungsanleitung

Kohler

Kohler 13EOZD Bedienungsanleitung

Kohler

Kohler K-9142 Bedienungsanleitung

Kohler

Kohler K-T16229 Bedienungsanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler K-T442 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung