Kohler Oblo K-124B16-SANA-CP Bedienungsanleitung

Installation Guide

Electronic Wall-Mount Faucet

Français, page “Français-1”

Español, página “Español-1”

1386732-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Do not use lithium

ion batteries with this product. Exposing lithium ion batteries

to water can result in a ﬁre.

NOTE: Follow the installation dimensions precisely as there is no

deep roughing-in kit available for this product.

NOTE: Unless otherwise indicated, the illustrations in the

document show installation with the water supply on the left. The

valve may be ﬂipped to accommodate a water supply on the right.

Observe all local plumbing and building codes.

Shut off the water supply.

Inspect the supply tubing for damage. Replace as necessary.

Site preparation and wall ﬁnishing may require additional tools

and materials.

Adjustable

Wrench

Sealant Tape

Hex WrenchAssorted

Screwdrivers

Plus:

• Wire Fasteners

• Woodworking Tools

• Pipe Fitting Tools

• Wood Screws

• 2x4s

• PVC Tubing

1386732-2-A 2 Kohler Co.

1. Install the Mounting Bracket

IMPORTANT! Your faucet model may have different framing

requirements other than those shown. Consult the speciﬁcation sheet

for your faucet model.

IMPORTANT! Make sure the location of the valve is correct before

securing in place. The centerline of the drain and faucet should be

in line with each other.

Construct the framing for your installation.

Secure the mounting bracket to the framing using four wood

screws.

(152 mm)

Kohler Co. 3 1386732-2-A

2. Install Tubing (Recommended)

NOTE: Tubing (not provided) can be attached to the mounting

bracket to route the cables and the spout tube to the control box.

PVC ﬁttings (not provided) are recommended.

NOTE: Consult the speciﬁcation sheet to determine the control box

installation location.

Connect a straight tube to the mounting bracket. Make sure the

tube is long enough to reach the control box.

Connect a 90 degree elbow to the end of the tube at the control

box installation location.

Install the plaster guard with the screw.

1386732-2-A 4 Kohler Co.

3. Route the Cables and Tube

NOTE: Consult the speciﬁcation sheet to determine the control box

installation location.

Finish the wall with a 1-3/4″(44 mm) hole for the spout and a

1-1/4″(32 mm) hole for the sensor cables.

Remove the plaster guard.

Feed the sensor cables and tube from the spout through the

mounting bracket and down to the hole for the control box.

Take care to avoid kinking or damaging the cables and tube.

Finished

Wall

Ø 1-1/4"

(32 mm)

Ø 1-3/4"

(44 mm)

Kohler Co. 5 1386732-2-A

4. Install the Spout

Position the keyholes on the spout over the screwheads on the

mounting bracket. Loosen the screws if needed.

Align the spout by rotating clockwise.

Tighten the screws to secure the spout to the mounting bracket.

Slide the wall plate over the spout until ﬂush with the wall.

Secure the wall plate with the setscrew.

1386732-2-A 6 Kohler Co.

5. Install the Control Box

NOTE: Verify that the hose will reach the supply stop by attaching

the ﬂex hose to the control box inlet.

Verify that the sensor cable is below the countertop.

Unthread the control box screws to remove the cover.

Position the control box over the hole for the spout tube and

sensor cables.

Drill pilot holes.

Use the standard wall anchors (provided) depending on your

wall material.

Feed the spout tube and sensor cables through the slot in the

control box.

Attach the control box to the wall with the arrow pointing

upward. Secure with the two screws (provided).

Kohler Co. 7 1386732-2-A

6. Connect the Control Box

IMPORTANT! The control box cover has slots for the spout wires

to ﬁt. Verify that the wires are not pinched when installing the

cover.

Connect the 3-pin sensor cable from the valve cover to the 3-pin

sensor cable from the spout (red, white, and green cables).

Connect the solenoid cable from the valve cover to the solenoid

cable from the valve box (red and green cables).

Connect the 2-pin sensor cable from the valve cover to the 2-pin

sensor cable from the spout (orange and black cables).

Loosely secure the cover to the control box for future access.

Valve

Box

Valve

Cover

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

Power

Cable

Solenoid

Cable

3-Pin

Sensor

Cable

2-Pin

Sensor

Cable

2-Pin

Sensor

Cable

Spout

Wires

1386732-2-A 8 Kohler Co.

7. Supply Connections

IMPORTANT! The control box cover has slots for the spout tube

and cables. Use care not to pinch the tube or cables when installing

the cover.

Inlet Connections

Connect the ﬂex hose from the control box to the supply stop.

Outlet Connections

Feed the tube from the spout through the slot in the control box

cover.

Verify that the tube from the spout is the appropriate length to

reach the control box. Cut the tube if necessary. Remove any

burrs and sharp edges.

Insert the tube into the ﬁtting (control box outlet end) until the

tube stops.

Verify that the tube is secure.

Outlet Inlet

Flex Hose

Tube From

Spout

Supply

Stop

Flex Hose

Kohler Co. 9 1386732-2-A

8. Mixing Valve - If Included

If a mixing valve is included with your product, connect the

water outlet hose to the control box outlet.

Attach the supply hose to the control box inlet and outlet of

mixing valve.

Use a 3/8″compression connection (provided) to attach the cold

supply to the mixing valve cold inlet end (marked cold on the

adjustment plate).

Use a 3/8″compression connection (provided) to attach the hot

supply to the mixing valve hot inlet end (marked hot on the

adjustment plate).

Loosen the lock screw and adjust the temperature by rotating the

adjustment plate.

Retighten the lock screw.

Outlet

Hot Cold

Adjustment plate to

set water temperature.

Lock Screw

1386732-2-A 10 Kohler Co.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-2746X Montageanleitung

Kohler

Kohler TOOBI 8965IN-9FP Bedienungsanleitung

Kohler

Kohler K-8801 Montageanleitung

Kohler

Kohler K-877 Montageanleitung

Kohler

Kohler JULY 16316M-4 Bedienungsanleitung

Kohler

Kohler K-11496X Montageanleitung

Kohler

Kohler K-7305 Betriebsanleitung

Kohler

Kohler Alteo K-T45117 Montageanleitung

Kohler

Kohler Stance 10317T-4 Bedienungsanleitung

Kohler

Kohler K-8816 Bedienungsanleitung

Kohler

Kohler K-1124-G Kurzanleitung

Kohler

Kohler ALEO S 31240T-4 Bedienungsanleitung

Kohler

Kohler Elate 13963X-4 Bedienungsanleitung

Kohler

Kohler Revival K-2950-1/8 Bedienungsanleitung

Kohler

Kohler K-6330 Bedienungsanleitung

Kohler

Kohler K-15171 Montageanleitung

Kohler

Kohler JULY Series Bedienungsanleitung

Kohler

Kohler BOTTICELLI 2393-WH Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic 9.8kW 1.1746.006 Bedienungsanleitung

Kohler

Kohler Moxie K-14292 Bedienungsanleitung

Kohler

Kohler K-13717 Bedienungsanleitung

Kohler

Kohler CFI230G Bedienungsanleitung

Kohler

Kohler 114749-9-AE Handbuch

Kohler

Kohler K-454 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung