Kohler PATIO ECO K-16321T-Y Bedienungsanleitung

1154809-T01-B

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

·-

Open end/adjustable wrenches

Tape measure

Basin wrench

Pipe wrench

Square

Level

Pliers

Socket wrench with sockets

Screw driver

Seal tape

Connection wire

Wire cutter

Insulation tape

Bushing

Drill

Sealant

RECOMMENDED TOOLS AND MATERIALSRECOMMENDED TOOLS AND MATERIALS

PATIO ECO

INSTALLATION INSTRUCTIONS

0.5

0.5L TOUCHLESS URINAL

K-16321T-Y(DC/ )

K-16321T-YC05(AC/ )

-1-

BEFORE YOU BEGINBEFORE YOU BEGIN

, 2011

528137

1154809-T01-B

Note: the sensing distance in the table is measured with a 30 30cm white board as the reflecting surface.

Model

Power

Liter per flushing

Temperature

Starting pressure

Testing time

Flushing mode

Sensing distance

16321T-Y 16321T-YC05

220V AC 50/60Hz

Water pressure at 0.18~0.55 MPa: Average flushing no more than 0.5L

Environmental temperature: 1 to 55 C

0.05~0.86MPa

70cm away from sensing window (Automatic adjustiment range: 50~70cm)

About 2 seconds or 5 seconds (Automatic adjustment)

Flushing after used

2 "AAA" size alkaline batteries

16321T-YC05

0.18~0.55MPa. 0.5L

1~ 55 C

0.05~0.86MPa.

70cm ( 50~70cm)

25( )

220V 50/60Hz

16321T-Y

2 7 (AAA 2)

30 30cm2

SENSOR SPECIFICATIONSSENSOR SPECIFICATIONS

-2-

ROUGHING-IN

Unit:mm

Reference Value

Kohler reserves the right to change marked dimensions without prior notice.

332

180

600 50 ext

145

55 642

303

G1/2

180

180 5

Notice: a. The dimensions above are just for reference.

b. The layout dimensions of water and outlet see

installation step B(Install the hook).

c. ** Indicates the location of inlet pipe, while inlet

connector size is G 1/2.

d. * Recommended dimensions for installation only,

please adjust according to actual situation.

inlet

b. B( )

c. ** G 1/2

d. *

1154809-T01-B -3-

Outlet Downwards

1. Please install 16321T-YC05(AC) as below:

Please directly reference to Step 2 when installing 16321T-Y

(DC).

CAUTION:

Please match 16306T-NA AC power unit when installing

16321T-YC05 (AC).

a. Outlet of AC power unit upward prohibited.

b. Do not connect 220V AC power supply to DC wiring

terminal.

c. Do not damage the covering of AC power unit or

remove screws to avoid leakage.

1.()

b. 220V DC

() 2

( ) 16306T-NAA.

16321T-YC05

16321T-Y

16321T-YC05

Outlet Upwards

Connect to

Sensor

Connect to

Sensor

Connect to AC

Power Supply

Connect to AC

Power Supply

INSTALLATION

CAUTION:

. When installing the power unit on the ceiling, please

chisel out a slot and layout bushing according to Fig., and

thread wire through the bushing.

One AC power unit can supply two

sensors at most.

Ceiling

Slot

AC Power Unit

Bushing(In-wall)

()

Bushing

()

(In-wall)

Notice:

. AC power unit connected to electric control box by

connection wire.

The length of the connection wire should keep

the connector out of the urinal. It s convenient

connect.

16306T-NA

AC Power Unit

Connector

Wire Prepared

By Customer

Connect With

Control Box

Connect with the same color wire,

and protect connect area by insulation tape.

Notice: To ensure an effective flush performance,

strongly recommended inner diameter of

water supply (including water meter, valve,

etc.) is no less than 25mm, and supplied

water pressure (sensor inlet dynamic

pressure) is 0.18MPa ~0.55MPa.

(

) 25mm (

) 0.18MPa ~0.55MPa

1154809-T01-B -4-

Notice:

f. Don't install the AC power unit in the free

space behind the urinal to avoid damaging

the AC power unit.

b. Do not connect the DC output of AC power

unit to AC power supply.

c. Do not connect to power supply while

installing. Connection line is not supplied.

AC connection wire with insulating sleeving

is recommended. Wire of which the

nominal section area of conductor is not

less than 0.5mm is also recommended.

DC connection line use wire of which the

nominal section area is not less than

0.3mm . It is cut according to acted

installation requirements(The length of cut

wire is recommended less than 10m).

d. The head AC power supply must be

protected with appropriate fuse.

e. Please confirm the AC power supply and

water supply should be shut off before

maintaining the products with AC power

related.

a. Keep the connector away from water. a.

0.5mm

0.3mm

( 10m)

2. Install urinal

Notes: a. Observe all local plumbing and building

codes.

b. Shut off the water supply.

c. Carefully inspect the new fixture for any sign

of damage.

d. Be very careful while hand ling vitreous

china products.

Note:

Install outlet connection

Ascertain the position for outlet connection according to

rough-in dimension.

Connect the outlet connection with the S-trap way. Insert the

gasket into the S-trap way as shown. Apply sealant on outlet

pipe, connect the outlet connection with outlet pipe.

Maybe different for different outlet connections.

X1 X1

1154809-T01-B

Install hook

Drill 2 mounting holes on the wall and install hook. Fix hook

on the wall by tightening screws.

-5-

Supply Pipe

Install the inlet hose of valve assy.

Take out the bracket of valve assy. Install the limited board (1).

Tighten the tighten screw (2).The inserting depth postion is

shown

Connect the inlet pipe with the water supply on the wall.

(1) (2)

(3)

as (3).

Limited Board

Tighten Screw

Bracket of Valve Assy.

(1)

Bracket of Valve

Tighten Screw

(2)

(3)

180

1154809-T01-B -6-

Install urinal

)

Lift up the urinal, level the installing hole on the back of the

urinal with the hook. Level the outlet connection which is

installed together with the strainer and the gasket on the S-

trap way. Then insert the outlet connection into the gasket.

(While the outlet connection is inserted, the S-trap way can

be crutched by hard exterded via the gap in the bottom of the

urinal to install it decently.) Then fix the urinal on the hook.

a. Avoid the urinal fallen on the floor to

damage the urinal or hurt somebody.

b. Avoid damaging the valve assy and wires.

c. Confirm the wires bare out of urinal base.

Notice:

d. Set the inlet hose and the inlet hose of

valve assy respectively on the both sides of

the S-trap way before installing urinal.

Inlet Hose of Valve Assy

Inlet Hose

Inlet Hose of Valve Assy

1154809-T01-B

3. Install the bracket assy.

Note:

Connect the outlet of valve assy, with the inlet hose.

The way of (DC) installation is as below:

Take out the battery box from the bracket assy. Loose the

screws of the battery box assy with a screw driver. Put 2

"AAA" size alkline batteries and tighten the battery box's

cover with the screws. Replace the battery box. Connect the

wires with the same color wires.

Don't mistake the polarity of the batteries and

don't mix the new and used batteries together.

Installing (AC) must connect the AC power unit

with control box assy with the same color wires.

16321T-Y

16321T-YC05

()

16321T-Y

16321T-YC05

Note:

Press the two sides spring hooks of bracket of valve assy

close to the center(1). Press the bracket up along the wall

and push it into arc gap of the urinal base(2) until the

spring hooks hangs on the urinal.

Please carefully handle the stainless steel plate

for its sharp edge will cause possible handcut.

(1)

(2)

When installing 16321T-YC05,

connect DC output

16321T-YC05

Inlet Hose

Connector

When installing 16321T-Y,

connect battery box

16321T-Y

Inlet Hose of Valve Assy.

Bracket of Valve

Outlet

Screw M2.5X20

M2.5X20

Cover of Battery Box

Battery Box

Bracket of Valve Assy

Spring Hook

(1)

Spring Hook

(2)

(1)

Urinal

-7-

1154809-T01-B

Push the bracket away from the wall(3), until the front hook

of the bracket hanging on the urinal.

(3)

Note:

Loose the tighten screw. Push the limited board to the

urinal withstanding the wall (4) and then tighten the tighten

screw (5).

a. When installing the 16321T-YC05(AC), do

not connect to power supply until finish

installation.

b. Taking out the bracket just need to athwort

the way of installations.

(5)

(4) (5)

a. ( )

220V

16321T-YC05

Limited Board

(3)

(4)

(5) Tighten Screw

Front Hook

-8-

1154809-T01-B

USER S GUIDE

Don t use this system until the power is on for 10

minutes.

The sensing distance will be adjusted and the system

will not work during this time.

Working Status

Before powering the system on, chear the unwanted objects

in front of the sensor window lest shortening the sensing

distance.

Sensing Distance

During the first 10 minutes, when powered on, the system is

in the phase of automatic regulation, and no operation is

required.

Deodorizing Flushing

The urinal will take a flush automatically when it’s used 3 or 4

times in 2 minutes.

2 3-4

Replacement of Batteries(Only for )

When out of power, the indicator will flash every 2 seconds

and the sensor will not work until new batteries are supplied.

When replacing batteries, open the cover of battery box and

put in new batteries.

()

16321T-Y

Indicator

-9-

1154809-T01-B -10-

Manual Flushing

Approach the supplied special magnetic stick (flushing control

stick) to the sensor lens. The system is now at a manual

status and the indicator will flash every 1 seconds. Approach

the flushing control stick to the sensor lens once, it ll flush

once. This status will last for about 8 minutes until turns to the

normal working status.

If the flushing control stick keeps near to the

sensing window for 30 seconds, the manual

status will be terminated automatically and

reassume the normal working status.

()

Notice:

Used in places of low water pressure

If the flushing amount is limited due to low water pressure,

you can set a long time washing with flushing control stick.

Operate as follows: Ten minutes after power-on, you can

switch between two wash times by putting the flushing control

stick near the right side of sensing window. There will be a 2-

second rinse after you complete the setting. If you need to

reset the wash time, you must cut off the power and restart

the sensor and 10 minutes later, you're able to switch wash

time with flushing control stick.

Under the normal water pressure, it is not

recommended to use this flushing method in

order to prevent excessive flushing and water

spills out.

Note:

()

Flushing Control Stick

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-6350 Bedienungsanleitung

Kohler

Kohler TAHOE Bedienungsanleitung

Kohler

Kohler K-T395 Montageanleitung

Kohler

Kohler July 16027 Bedienungsanleitung

Kohler

Kohler K-2972 Montageanleitung

Kohler

Kohler rada Intelligent Care MX1 Series Bedienungsanleitung

Kohler

Kohler K-18829 Montageanleitung

Kohler

Kohler Aleo 77751X-4CD Bedienungsanleitung

Kohler

Kohler K-13490 Montageanleitung

Kohler

Kohler K-7776 Bedienungsanleitung

Kohler

Kohler K-13132-3A Montageanleitung

Kohler

Kohler K-6941 Montageanleitung

Kohler

Kohler K-15246X-S Montageanleitung

Kohler

Kohler K-18485 Montageanleitung

Kohler

Kohler K-73078 Montageanleitung

Kohler

Kohler Cleansing Seat Montageanleitung

Kohler

Kohler MEMOIRS Series Bedienungsanleitung

Kohler

Kohler K-10094 Montageanleitung

Kohler

Kohler 10868T-B4 Bedienungsanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler VEIL HT100 TL IWT Bedienungsanleitung

Kohler

Kohler K-170 Montageanleitung

Kohler

Kohler K-7825 Bedienungsanleitung

Kohler

Kohler GEOG K-21727T-PF040-Q73 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung