Kohler K-18829 Montageanleitung

Installation and Care Guide

In-Wall Tank and Carriage

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-18829

1246750-2-B

Tools and Materials

Before You Begin

IMPORTANT! 2x4 framing is required for this product.

IMPORTANT! In areas with freezing temperatures, install on an

interior wall. If installed on an exterior wall, provide adequate

insulation to prevent the possibility of freezing.

NOTE: If 2x6 framing is used, the drain outlet may be angled 45

degrees in either direction.

NOTE: This device is not intended to be used as a retroﬁt device

for 1.28 gpf (4.8 lpf) water closets.

NOTE: Performance may vary. This product was tested with toilets

that are listed as compatible.

Only bowl numbers K-6299 and K-6300 are compatible with the

carriage.

During installation, make sure the inlet tube connections and

gaskets remain fully engaged to ensure a watertight seal.

Carefully inspect the carriage and tank for damage.

Observe all local plumbing and building codes.

For Installations with a Bidet Seat

CAUTION: Risk of personal injury. If the optional electrical

outlet will be installed, it must be connected to a GFCI or

RCD protected circuit.

Plus:

• Conventional woodworking

tools and materials

• 1/4" x 2" (51 mm) Min

Concrete Expansion Bolts

(for concrete subflooring)

Optional:

• Assorted electrical tools

5/8"

(16 mm)

1/2"

1/4 turn, 1/2" NPT

Supply Shut-off with

5/8" or Shorter Handle

1/4" x 2" (51 mm) Min

Lag Bolts

Silicone Plumbers

Grease

Assorted Drill Bits

1246750-2-B 2 Kohler Co.

Before You Begin (cont.)

If the optional electrical outlet will be installed, observe all local

electrical codes.

Kohler Co. 3 1246750-2-B

1. Install the Framing

IMPORTANT! Note the 1-3/4″(44 mm) or 3-1/4″(83 mm)

dimension from the front edge of the framing to the center of the

outlet pipe depending on your installation. This dimension is critical

for the installation.

NOTE: Refer to the speciﬁcation sheet for more details and

dimensions for roughing-in.

NOTE: The waste outlet pipe may need to be relocated for this

installation.

NOTE: A PVC elbow is supplied with this product. A cast iron

elbow may be required by codes in some areas. The height of the

toilet drain pipe may need to be adjusted if the cast iron elbow is

used.

NOTE: Double studs must be used on either side of the stud

pocket.

Construct the stud pocket using the dimensions shown.

1-3/4" (44 mm) [2x4 Studs]

3-1/4" (83 mm) [2x6 Studs]

2x4 Studs or

2x6 Studs

8" (203 mm) [Plywood Subfloor]

9-1/8" (232 mm) [Concrete Subfloor]

Waste

Outlet

Pipe

23-1/4"

(591 mm)

PVC

Elbow

1-3/4" (44 mm) [2x4 Studs]

3-1/4" (83 mm) [2x6 Studs]

1246750-2-B 4 Kohler Co.

Install the Framing (cont.)

The center of the waste outlet should be 1-3/4″(44 mm) or 3-1/4″

(83 mm) from the front edge of the framing.

Kohler Co. 5 1246750-2-B

2. Prepare the Carriage

Install the Drain Clamp

Unpack and inspect the carriage.

NOTE: If using 2x6 studs, install the mounting frame reversed into

the back notches.

Install the mounting frame into the front notches on the bottom

of the carriage.

Insert the PVC elbow into the mounting frame.

Secure the elbow in place with the drain clamp. Push the clamp

into the frame until it locks into place.

Install the Electrical Box - Bidet Installations

NOTE: The 1201721 electrical box kit is required when the K-4744

bidet seat will be paired with the bowl. Skip this step for standard

installations.

Connect the electrical box to the carriage at the location shown.

Electrical

Box

Back View

Mounting

Frame

PVC

Elbow

Front View

Drain

Clamp

1246750-2-B 6 Kohler Co.

3. Adjust the Carriage Height

IMPORTANT! If the carriage is not correctly adjusted, the bowl rim

height may not be compliant with applicable codes. The ﬁnished

wall would need to be removed to make the correct adjustments if

the bowl height is not correct.

NOTE: For the K-6299 and K-6300 bowls, the minimum rim height

is 15″(381 mm) when the ﬁnished ﬂoor is even with the bottom of

the carriage legs. The maximum rim height is 23″(584 mm) when

the legs are fully raised. The carriage can be adjusted up to 8″(203

mm), with 6″(152 mm) or less of adjustment sufficient in most

installations.

Move the carriage into place in the stud pocket.

Temporarily secure the carriage in place so it will not fall.

Install the threaded rods several turns into the carriage.

Make a mark on the carriage 2-5/8″(67 mm) above the top of the

threaded rod.

Measure from the ﬁnished ﬂoor to the mark (A) to determine the

rim height of the bowl.

Leg

Nut

Finished

Floor

Mark the carriage.

2-5/8"

(67 mm)

Threaded

Rods

Kohler Co. 7 1246750-2-B

Adjust the Carriage Height (cont.)

Loosen the nuts securing the legs to the carriage.

NOTE: As the carriage is lowered, make sure the elbow aligns with

the toilet drain pipe.

NOTE: If applicable, conﬁrm the gasket on the elbow stays

correctly positioned as it enters the toilet drain pipe.

Adjust the carriage until the desired height is reached. Securely

tighten the nuts using a wrench to secure the legs in place.

NOTE: If a cast iron elbow is required, make the connections

following all applicable codes.

1246750-2-B 8 Kohler Co.

4. Install the Carriage

Align the carriage ﬂush with the front edge of the studs. The

front of the carriage should be ﬂush with the front edge of the

studs or set back slightly for ﬁnished wall installation.

Check the front of the carriage for plumb.

Mark the hole locations for the six lag bolts, one for each foot and

two on either side of the carriage.

Drill pilot holes (remove the carriage if needed) to reduce the risk

of the lag bolts causing the studs to split or crack.

NOTE: If the carriage is installed onto a concrete sub-ﬂoor use

concrete expansion bolts (not supplied) when securing the feet of

the carriage.

Secure the carriage to the support studs using 2″(51 mm) long

(minimum) lag bolts (not supplied), one at each location.

Connect the Power - Bidet Seat Installations

WARNING: Risk of personal injury. Disconnect the power

before connecting the wires.

Lag Bolts

Kohler Co. 9 1246750-2-B

Install the Carriage (cont.)

CAUTION: Risk of personal injury. The electrical outlet

must be connected to a GFCI or RCD protected circuit or an

accessible Ground-Fault Circuit-Interrupter (GFCI) or

Residual-Current Device (RCD) must be installed.

NOTE: This step is only needed if the electrical box was installed in

the ″Prepare the Carriage″section.

Connect the power following all applicable codes.

1246750-2-B 10 Kohler Co.

Andere Handbücher für K-18829

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13770 Bedienungsanleitung

Kohler

Kohler COMPOSED K-EX34060T Bedienungsanleitung

Kohler

Kohler Leighton K-2326 Montageanleitung

Kohler

Kohler C3-255 Bedienungsanleitung

Kohler

Kohler K-12181 Montageanleitung

Kohler

Kohler Soleo 8690 Bedienungsanleitung

Kohler

Kohler KARAT K-23883 Bedienungsanleitung

Kohler

Kohler KT6908 Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.8 kW Bedienungsanleitung

Kohler

Kohler K-75449-BN Bedienungsanleitung

Kohler

Kohler Memoirs K-2238 Montageanleitung

Kohler

Kohler 11829T-B Bedienungsanleitung

Kohler

Kohler K-T461 Bedienungsanleitung

Kohler

Kohler Kelston K-T13494 Montageanleitung

Kohler

Kohler K-6487 Bedienungsanleitung

Kohler

Kohler K-13132 Montageanleitung

Kohler

Kohler K-9530 Montageanleitung

Kohler

Kohler K-2294 Bedienungsanleitung

Kohler

Kohler C3-130 Bedienungsanleitung

Kohler

Kohler URBANITY 23748T-9 Bedienungsanleitung

Kohler

Kohler CUFF 37310M-4 Bedienungsanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-146 Montageanleitung

Kohler

Kohler AMARETTO K-4864T-1/4 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung