Kohler REGATTA drop in 11303A-GAB-0 Bedienungsanleitung

ROUGHING-IN & DIMENSIONS

• Please read these instructions carefully to familiarise

yourself with the required tools, materials, and

installation sequences. Follow the sections that

pertain to your particular installation. This will help

you avoid costly mistakes. In addition to proper

installation, read all operating and safety instructions.

• All information is based on the latest product

information available at the time of publication.

Kohler NZ Ltd. reserves the right to make changes in

product characteristics, packaging, or availability at

any time without notice.

• These instructions contain important care, cleaning,

and warranty information-



A. BUBBLE MASSAGE BATH

Ordering Information

REGATTA drop in

B. Required Electrical Service

Dedicated branch circuit required, protected with Class

A Ground-Fault Circuit-Interrupt (GFCI):

Blower 220~240V, 10.A, 50Hz

C. Installation

Read the entire installation instructions before beginning

the installation.

BEFORE YOU BEGIN

BUBBLE MASSAGE BATH

INSTALLATION INSTRUCTIONS

1128227-A01-D Date: 13/8/2010

Blower Heater Voltage Freq Amperage

Motor

Part #

Kohler AP300 - air switch 300 W 180W 220~240 V 50-60Hz 2.2A

1128A-CP

Product Air switch

11303A-GAB-0

EVOK RECT drop in

EVOK RECT freestanding

EVOK OVAL drop in

18344A-GAB-0

18263A-GAB-0

18346A-GAB-0

EVOK OVAL freestanding 18348A-GAB-0

1709A-GAB-0

ESCALE drop-In

ESCALE free Standing

11343A-GAB-0

11344A-GAB-0

OVE RECT drop in

D. Dimensions

Detached blowers are supplied with a 1.5m flexible coupling. This allows the blower to be positioned at the installers

discretion. For serviceability of the blower, an access panel of 450mm x 400mm must be fitted. If access to the

blower is not provided, then no warranty service will be provided.

If supply cord or interconnection cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

REGATTA BUBBLE MASSAGE 11303A-GAB-0

1128227-A01-D Date: 13/8/2010





















OVE BUBBLE MASSAGE 1709A-GAB-0

















1128227-A01-D Date: 13/8/2010 +

EVOK BUBBLE MASSAGE 18263A-GAB-0













EVOK RECT FREESTANDING BUBBLE MASSAGE 18344A-GAB-0

837.5

1675

762

408.5

513

610

1128227-A01-D Date: 13/8/2010

EVOK OVAL BUBBLE MASSAGE 18346A-GAB-0

EVOK OVAL FREESTANDING BUBBLE MASSAGE 18348A-GAB-0

398

750

1700

850

510

610

398

750

1700

850

530

ESCALE DROP-IN BUBBLE MASSAGE BATH 11343A-GAB-0

1128227-A01-D Date: 13/8/2010

ESCALE FREESTANDING BUBBLE MASSAGE BATH 11344A-GAB-0



 

























61128227-A01-D Date: 13/8/2010

PRODUCT REQUIREMENTS

A. Summary Of Key Requirements

• Observe all local plumbing codes.

•

• Provide properly-dimensioned framing.

• Baths with airjets are designed for a variety of

installations, depending upon the model chosen.

between the valves and spout may be required.

that may inadvertently be used as a means of support

are not appropriate or safe for this installation.

D. Product Inspection

Carefully unpack and inspect the bath with airjets

for damage. Leave all materials in the carton during

construction to prevent damage.

C. Electrical Requirements

The installation must have a Class A Ground-Fault

Circuit-Interrupter (GFCI). The GFCI protects against

Line-to-ground shock hazard. Use a 220-240 V, 10A

(minimum), 50 Hz dedicated service for the bath with

airjets.

PRODUCT NOTICES

WARNING: Risk of electrical shock. A licensed

electrician should make all electrical connections.

WARNING: Risk of electrical shock. Connect

only to a circuit protected by a Ground-Fault

Circuit-Interrupter (GFCI) or Earth-Leakage

Circuit-Breaker (ELCB).

WARNING: Risk of electrical shock. Disconnect



WARNING: Risk of injury or property damage.

Please read all instructions thoroughly before

beginning installation, including the following

Product Requirements.

WARNING: Keep the area around the blower

motor clean and free of debris.Ensure that the

area around the blower motor is free of sawdust,

insulation, dirt, or other small loose debris. Such

material could clog the blower motor air ducts and

cause unsafe operation or affect performance

of the bath with airjets. Do not relocate the

system in the absence of kit instructions, as this

could adversely affect the performance and safe

operation of the bath with airjets. Kohler NZ shall

not be liable under its warranty or otherwise for

personal injury or damage caused by any such

A. Installation Hazard Notification

B. Plumbing Specifications

INSTALLATION REQUIREMENTS

A. Tools Required

• Adjustable pipe wrench

• Rule

• Level

• Safety shoes

• Safety glasses

• Square

• Screwdriver

• Pliers

• Utility knife

• Pencil

• Measuring Tape

B. Materials Required

• Plumber’s putty

• Wall coverings, as

necessary

• Silicone sealant

• Gypsum cement

(optional)

• Construction adhesive

(optional)

• Protective covering for

bathtub

• Nails

• Silicone Sealant

Plus:

• Conventional woodworking tools and materials or

conventional bricklaying tools and materials

• Drop Cloth

• Construction adhesive (optional)

• Cement or mortar (optional)

• 2x4s or 2x6s

• PVC Cement

71128227-A01-D Date: 13/8/2010

A. Prepare the Site

CAUTION: Risk of product damage. Do not

only support the bath by the rim.

NOTICE:

under the bath must provide for a minimum of 80 lbs./

square foot (390kg./square metre) loading.

NOTICE: Provide adequate ventilation and a minimum

of 15 cubic feet (.4 cubic metres) in the installed

air for the blower. Do not install the blower motor closer

than 2.5mm from the wall or other objects.

•

• This bath may be installed in a drop-in or in an island

installation. An island installation requires a four-side

surround.

• Install an access panel to allow the blower to be

serviced. Ventilation access is recommended.

• Construct brick, concrete or timber supports.

• Ensure the bath rim is fully supported. Frame the

accordance with the roughing-in information packed

with the bath.

Approved Tile Backing

Typical

Bath

Tile

Brick

timber

access

panel

Approved Tile Backing

Install an access panel to allow

the pump to be serviced.

Bath may be installed next to the

Bath rim must be fully supported.

wall or as an island installation.

Tile Brick

timber

B. Whirlpool Area Construction

Preparation (Optional)

Make sure you allow for access to the blower in the

event the unit requires service. When constructing the

material (e.g. mortar mix and ceramic or marble tiling).

When choosing a blower installation position, check

that the switch cable will reach the blower.

Drop In Installation: Refer to rough-in notes on page 2

for cut-out details. Whirlpool must be supported both

on the rim and on the supporting feet. Do not allow the

whirlpool to be supported by the rim alone.

Bath Rim

BEFORE INSTALLING

A. Your new whirlpool has been manufactured to the

highest possible standards, it has been factory tested

and approved.

B. When removing bath from protective carton DO

NOT LIFT BATH BY PIPE WORK. Inspect for any

possible damage that may have occurred in transit.

Position a clean drop cloth or similar material in the

scratch the surface of the bath.

SITE REQUIREMENTS

1128227-A01-D Date: 13/8/2010

D. IMPORTANT: Bath must be installed level on all top

edges.

E. Install the drain to the bath according to the drain manufacturer’s instructions. Do not connect the trap at this time.

If a pop up waste/overflow has been selected as an accessory, then an extra overflow hole might require drilling.

The position of the overflow holes are shown on page 2. (Refer to part ‘M’ in the next section for cutting and drilling

instructions)

C. Identify suitable blower installation and access positions

before proceeding with installation. A suitable power

outlet will also be required within 610mm of the blower.

See section H.

NOTE: NO MOTOR ACCESS NO WARRANTY

SERVICE. Ventilation must be provided in order to

allow heat from motor to dissipate.

Blower Access*

INSTALL THE BATH

CAUTION: Risk of product damage. Do not lift

the bath with airjets by the air channels or blower

motors, or use the air channels or blower motor

for structural support of the bath.

CAUTION: Risk of product damage. Do not

support the bath by the rim.

as necessary.

A. Option Using a Cement or Mortar Bed

NOTE: Do not use gypsum cement or drywall

compound for this application, as they will not provide

an acceptable, durable bond.

• Spread a 50mm thick layer of cement or mortar on

secure, level, and support the unit. Clear all the

material away from the support block locations.

• Position a piece of plastic drop cloth material on top

of the cement or mortar bed.

• With help, carefully lift the bath into place, and

make sure the support blocks do not rest in the bed

Material.

• Insert the drain tailpiece into the trap. Make sure the

bath is level and resting on all support blocks.

• Remove the protective tape from the rim.

Spread a 50mm Layer

of Cement or Mortar

Bed Material.

Clear spaces

for support blocks.





91128227-A01-D Date: 13/8/2010

Apply Construction

adhesive to the

Support Blocks.

B. Option Using Construction Adhesive

• Apply a generous amount of high-quality construction

adhesive to the bottom of the support blocks.

• With help, carefully lift the bath into position.

• Insert the drain tailpiece into the trap. Make sure the

bath is level and resting on all support blocks.

• Remove the protective tape from the rim.

Bath Rim

C. Option Using Silicone Sealant

• With help, carefully lift the bath into position.

• Insert the drain tailpiece into the trap. Make sure the

bath is level and resting on all support blocks.

• Remove the protective tape from the rim. Apply a

continuous bead of high-quality silicone sealant

around the entire rim of the bath.

• Allow the sealant to cure according to the

manufacturer’s instructions.

E. Install the Blower Switch (For Detached Blower Versions Only )

D. Install the pillow rail

(Regatta Bubble Massage Bath Only )

•

Refer to the exploded view for installation

of the pillow rail.





















To the blower

Air Switch

Bath Flange

Connect the air tube to the switch and to the blower.

•

Apply silicone sealant to switch and press into hole.

•

Apply Silicon Here





Remove any excess silicone with a rag.

•

1128227-A01-D Date: 13/8/2010

I. Test Run the Bath with Airjets

• For information on unit operation, refer to the

• Check all electrical connections, and make sure the

electrical power to the bath with airjets is on.

• Make sure all piping connections in the air harness are secure.

• Verify that the blower motor is secure.

• Temporarily remove the plastic drop cloth or other

protective sheeting from the bath.

• Fill the bath to a level at least 50mm above the top of

the highest airjet.

• Check the drain piping for leaks. Repair any leaks.

•

airjets. Check the air piping for air leaks.

• Stop the bath and drain the water.

• Return the plastic drop cloth or other protectivesheeting

to the bath. Check the drain connections for leakage.

H. Make Electrical Connections

WARNING: Risk of electric shock. To reduce the

risk of electrical shock, connect the blower motor

to a properly grounded, grounding-type receptacle

protected by Ground-Fault Circuit-Interrupters

(GFCIs). Do not remove the plug grounding pins.

Do not use grounding adapters.

NOTE: The model number and electrical rating of the blower

is printed on the blower.

• The blower is equipped with a cord and plug. A licensed

electrician must install a dedicated GFCI-protected, 220V, 10A,

grounded outlet. Locate the outlet behind the bath, and within

610mm of the blower motor.

• Plug the blower motor into this outlet.

• Clean the area of all dust and debris.

GFCI-Protected Receptacle Blower Motor

G. Install the Plumbing

CAUTION: Risk of property damage. Ensure a

watertight seal on the bath drain.

• Connect the drain to the trap according to the

manufacturer’s instructions.

NOTICE: An access panel will simplify future maintenance.

• Install the faucet valving according to the faucet

manufacturer’s instructions. Do not install the faucet

trim until instructed. Open the hot and cold water

supplies, and check the supply connections for

leakage.

• Run water into the bath, and check the drain

connections for leakage.

F. Install the Blower

(For Detached Blower Versions Only )

•

Connect the flexible coupling to the blower

using PVC cement

•

Once connected find a suitable installation position for

the blower.

•

Secure the blower firmly using appropriate fixings so

that the blower can not vibrate free when in use

The detached blower can be installed up to 1.5m from

the bath if desired.

Appropriate fixings

through holes in blower

Apply PVC Cement Here

Air blower must be located or fixed so that it cannot

fall into the bath of spa.

•

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-T16236 Bedienungsanleitung

Kohler

Kohler K-16230 Bedienungsanleitung

Kohler

Kohler MING K-20029T-RW1 Bedienungsanleitung

Kohler

Kohler K-6274 Montageanleitung

Kohler

Kohler K-72218-2BZ Bedienungsanleitung

Kohler

Kohler 5838W-7U-0 Bedienungsanleitung

Kohler

Kohler K-13770 Bedienungsanleitung

Kohler

Kohler K-377 Bedienungsanleitung

Kohler

Kohler K-702-N1 Bedienungsanleitung

Kohler

Kohler K-10088 Montageanleitung

Kohler

Kohler ATOM 28956X-4 Bedienungsanleitung

Kohler

Kohler SYMBOL 72640X Bedienungsanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler Margaux 16238-4-CP Montageanleitung

Kohler

Kohler WELLWORTH WATERGUARD K-3520 Bedienungsanleitung

Kohler

Kohler K-2032-0 Bedienungsanleitung

Kohler

Kohler Kumin K-104K36-SANA-CP Bedienungsanleitung

Kohler

Kohler 1202901-5-B Montageanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler Trend K-11935 Montageanleitung

Kohler

Kohler MAXISPACE K-77217T Bedienungsanleitung

Kohler

Kohler PURIST UPGRADE K-99168T Bedienungsanleitung

Kohler

Kohler BRAZN K-702242T Bedienungsanleitung

Kohler

Kohler K-7827 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung