Kohler BRAZN K-702242T Bedienungsanleitung

1463408-T01-A

-1- © Copyright Kohler China Investment Co., Ltd. 2020

ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH

DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437

中山科勒卫浴有限公司广东省中山市中山火炬开发区兴业路 13-1 号邮编：528437

BEFORE YOU BEGIN 安装之前

• 说明书中所有的资料是按最新出版的产品资料编写而成。

科勒中国有限公司保留任何时候无须通知即可改变产品特

性、包装或产品可供类型的权利。

•说明书包括重要的安装、清洁及保养方面的内容，请把这

些资料交给用户阅读，保管。

• 确保在安装淋浴房之前已经完整正确地安装了浴室和完工

墙面材料。淋浴区墙地面应做防水处理，并不得布置有电

器开关、插座。确保地面排水通畅。

•在进行淋浴房安装之前，请拿出、排列并确认所有的零部

件。请参考第 2 页上所示的分解图。

• 对尺寸与本标准产品不同的定制淋浴房，参照本说明书进

行安装。

• 本产品符合 QB 2584-2007。

• All information is based on the latest product information

available at the time of publication. Kohler China Ltd.

reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

•These instructions contain important care, cleaning, and

warranty information-please leave these instructions for

the consumer.

• Make sure that the bath and the finished wall material are

completely and correctly installed prior to installing your

shower door. Prepare waterproof layer to wall and floor of

the showering area. It is not allowed for any presence of

electric switches and sockets. Make sure the floor drain

runs smoothly.

•Before starting the door installation, lay out and identify all

the parts. Use the exploded view illustrated on page 2 for

reference.

• For the installation method of customized shower with

different dimensions, please refer to this instructions.

•The product complies with QB 2584-2007.

警告：可能有人员伤害或者产品损坏的危险。

钢化玻璃不能进行切割，钻孔或硬物敲击。搬移或安装

过程中，小心确保玻璃边、角部位不受撞击，以防爆裂

伤人。

建议：将本产品安装在科勒淋浴盆或挡水条上（需另行购买）。

如自备挡水条，建议顶面宽度尺寸大于 80mm。

重要事项：淋浴房需要安装在平坦垂直的墙面上。墙面的垂直度

推荐在正负 3mm/m 以内。如果超出此范围，科勒公司将不保证

淋浴房的完美使用。

CAUTION: Risk of injury or product damage.

Tempered glass cannot be cut, drilled or knocked by

hard object. Make sure corner area of the glass

refraining from knocking so as to cause personal injury

due to broken glass.

ATTENTION: Please install this door on Kohler receptors or

curbs (Not included). If the curb is not Kohler-branded, please

note its top width should be more than 80mm.

IMPORTANT: The shower door requires a flat vertical

finished wall. The squareness of the wall is recommended no

more than 3mm/m. KOHLER Company won't take

responsibility of the installation quality.

24hrs

ROUGHING-IN 尺寸图

Do not use the enclosure for at least 24 hours.

安装后 24 小时内请勿使用淋浴房。

Unit: mm

单位：毫米

SKU

K-702242T

B H

1850-22001100-2100

BRAZN 凌越

INSTALLATION INSTRUCTIONS

安装说明书

PIVOT, SCREEN, 2P1D, 10mm

屏风两固一活，10mm

K-702242T

Tools Required/所需工具

5mm Allen Key

5mm 六角扳手

2.5mm Allen Key

2.5mm 六角扳手

Masonry Drill &

6mm Drill Bit

冲击钻以及

6mm 冲击钻头

Pencil

铅笔

Level

水平仪

Measuring Tape

卷尺

Phillips Screwdriver

十字螺丝刀

Hammer

锤子

Knife

刀片

Caulk Gun

硅胶枪

Safety Goggles

护目镜

-2-

1463408-T01-A

Screw

十字沉头机制螺丝 M4×7×5

Side Cap, SS

顶侧装饰盖 ×2

Pan Screw

十字盘头机制螺丝 PM4×25×4

Wall Jamb Clamp, SS

竖材

Insert Seal

单边胶条

Hinge Panel Glass

固定玻璃

Side Seal

侧边防水胶条

Door Glass Assy

门玻组件

BRAZN Pivot Handle,

double Handle

L=1025mm 凌越对装拉手

Protect Strip

固玻底部保护胶条×2

Silicone Block

防水硅胶块

Bottom Washer

门玻固定座垫圈

Bottom Base, Door

门玻固定座

Bottom Base Cap

门玻固定座装饰盖

Seal Assy.Glass Door BRAZN

Pivot 回水槽组件

Bottom Rail Cover, SS

下横梁装饰盖材

2P1D Bottom Rail, SS

两固一活屏风下横梁

Screen Al Frame Outer Cap, SS

屏风型材外盖材

Al Frame, Screen On Glass

屏风固玻铝材

Screen Al Frame Inner Cap, SS

屏风型材内盖材

Panel Glass, BRAZN

Pivot 固定玻璃

Insert Seal

单边胶条

Wall Jamb Clamp, Left, SS

左竖材

Magnetic

嵌入式磁条

Glass Magnetic

门玻磁条

2P1D Top Rail, SS

两固一活上横梁

Pan Screw

十字盘头自攻螺丝 ST3.5×40

Top Cap, SS

顶装饰盖-B

Decorative Strip

装饰胶条

Screw

紧定螺丝M5×20

Top Hinge Assy

上转轴组件

Top Cap, SS

顶装饰盖-A

Insert Seal

单边胶条（固玻底部用）×2

X1 X1

X16

X12

X10

Magnetic 嵌入式磁条

Side Seal 侧边防水胶条

Top Cap, SS 顶装饰盖-A

Top Cap, SS 顶装饰盖-B

Glass Magnetic 门玻磁条

Protect Strip 固玻底部保护胶条

Insert Seal 单边胶条

Screw M4×7 十字沉头螺丝 M4×7

Screw M5×20 不锈钢紧定螺丝M5×20

Pan Screw PM4×25 十字盘头机制螺丝 PM4×25

Pan Screw ST3.5×40 十字盘头自攻螺丝 ST3.5×40

Hollow Wall Anchor, Nylon 膨胀套

Insert Seal 单边胶条(固玻底部用)

Seal Assy, Galss Door, BRAZN Pivot 回水槽组件

Decorative Strip 装饰胶条

BRAZN Pivot Handle, double Handle, L=1025mm 凌越对装拉手

Screen Al Frame Outer Cap, SS 屏风型材外盖材

2P1D Top Rail, SS 两固一活上横梁

Wall Jamb Clamp, SS 竖材

Screen Al Frame Inner Cap, SS 屏风型材内盖材

Bottom Base, Door 门玻固定座

Bottom Base Cap 门玻固定座装饰盖

Silicone Block 硅胶防撞块

Bottom Washer 门玻固定座垫圈

Door Glass Assy 门玻组件

Side Cap, SS 顶侧装饰盖

Top Hinge Assy 上转轴组件

Bottom Rail Cover 底横梁盖材

2P1D Bottom Rail, SS 两固一活下横梁

Al Frame, Screen On Glass 屏风固玻铝材

0mm

-3-

INSTALLATION 安装

1463408-T01-A

IMPORTANT:

Tray MUST be

level along front

edge.

重要：

底盘必须水平。

0mm

STEP

Install the tube so that it is horizontal.

放置挡水条，需确保挡水条放置水平。

Install the protective seal at the bottom of the fixed glass and the fixed glass on both sides.

安装固玻底部保护胶条和两侧固玻。

Install the fixed glass profile and the magnetic strip.

1. Insert the magnetic strip into the profile downwards.

2. Pat the whole profile into the fixed glass.

3. The distance from the measured profile to the wall material is about 662mm (the door

glass width is 650mm).

安装固玻型材和磁条。

1. 先将磁条自上而下插入型材；

2. 再将型材整体拍入固玻；

3. 量测固玻之间间距为 662mm 左右（门玻宽度 650mm。

Side distance: 20mm

距边20mm

22mm

PM4*25*4

Install the upper-wall profile and the lower beam with the former vertical to the floor and

20mm from the external edge (stone base surface width is 80cm).

安装上墙型材与下横梁，上墙型材需保持与地面垂直，且内偏 20mm 安装（石基面宽

80mm）。

Install the upper beam which falls into the vertical members on both sides downwards and

whose gap is about 22mm from the side of the wall.

安装上横梁，上横梁自上而下落入两边竖材内，上横梁缺口到墙边尺寸为 22mm 左右。

Install the stainless steel decorative material of the lower beam, the rotating shaft base, the

washer and the silicone bumper block, and install the decorative seal.

安装下横梁不锈钢装饰材、转轴底座、垫圈和硅胶防撞块 ,安装装饰胶条。

Step 1: Insert the decorative material of the lower beam into the

rotating shaft base in the direction of the arrow.

Step 2: Install the whole part on the lower beam.

Step 3: Adjust the left and right position of the decorative material

of the lower beam and lock by the screws.

Install the decorative seal.

第一步，下横梁装饰材按箭头方向插入转轴底座；

第二步，整体安装在下横梁；

第三步，调整下横梁装饰材左右位置，锁上螺丝。安装装饰胶条。

Note: The fixed glass must be able to

catch the silicone bumper block.

注意：固玻需贴住硅胶防撞块。

Screw

十字沉头螺丝M4×7

Step 1

第一步

Step 2

第二步

Step 3

第三步

Note: There are four M4 thread holes with

each side being locked by one screw.

注意，四个 M4 牙孔，每边能各能锁一个

螺丝即可。

662mm

The wall jamb

must be kept

vertical.

上墙材必须垂直。

Install the door glass,

Step 1: Lift the door glass and insert it into the base of the lower beam.

Step 2: Put the door glass in right position and set the upper beam into the rotating shaft

assembly on the top.

Step 3: Lock the screws and set screws.

(Note: Both the upper rotating shaft assembly and the lower base of the door glass can be

adjusted leftwards and rightwards, loosen the screws, adjust them into the appropriate

position and then lock them).

安装门玻，

第一步：将门玻抬起插入下横梁底座；

第二步：摆正门玻，上横梁套入顶部转轴组件；

第三步：锁上螺丝和紧定螺丝。

（注意：门玻上转轴组件和下底座都可以左右调节，松开螺丝，调整合适位置在锁紧即可。）

Install the handle and the decorative cover.

安装拉手和装饰盖。

Apply the silicone sealant.

打防水胶。

Install the side seal of the fixed glass (note to distinguish two types of side seals).

安装固玻单边胶条（注意区分两种单边胶条）。

Install waterproof seal and magnetic strip.

安装防水胶条和磁条。

Note: After installation, the magnetic strip is

flush with the waterproof seal.

注意：磁条安装后与回水胶条是平齐状态。

Note: The height of the side seal at

the bottom is 8mm, and it needs to

be attached to the stainless steel

decorative cover during installation.

注意：底部单边胶条高度为 8mm，且

安装时需要贴到不锈钢装饰盖。

Note: The height of the two

side seals is 12mm.

注意：此两处单边胶条高度

为12mm。

Note: There is a cutout in the side seal, and the

cutout must be flush with the end surface during

installation.

注意：侧边胶条有剪缺，安装时缺口平齐端面即可。

Note: The top wire of the handle

is facing down.

注意：拉手顶丝朝下。

Note: This position needs to

apply sealant.

注意：此处位置需要打胶。

Screw

紧定螺丝 M5×20

Screw

十字沉头螺丝M4×7×2

Screw

十字沉头螺丝M4×7×2

ST3.5×40 ×1

STEP

-4-

1463408-T01-A

12mm

8mm

Note: Sufficient

support must be

provided when

installing the door

glass.

注意:安装门时需

有足够支撑

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-2367 Bedienungsanleitung

Kohler

Kohler FOLIO K-2017IN-1 Bedienungsanleitung

Kohler

Kohler K-7514 Bedienungsanleitung

Kohler

Kohler Mira Response Handset L19A Bedienungsanleitung

Kohler

Kohler K-7914 Montageanleitung

Kohler

Kohler K-7397 Montageanleitung

Kohler

Kohler K-72218 Montageanleitung

Kohler

Kohler K-17492 Montageanleitung

Kohler

Kohler K-7776 Montageanleitung

Kohler

Kohler Archer K-2359X Montageanleitung

Kohler

Kohler Mira Sport Bedienungsanleitung

Kohler

Kohler K-T11077 Montageanleitung

Kohler

Kohler K-994 Bedienungsanleitung

Kohler

Kohler Levity K-706013-L Bedienungsanleitung

Kohler

Kohler K-2816 Bedienungs- und Wartungsanleitung

Kohler

Kohler Portrait K-2226 Bedienungsanleitung

Kohler

Kohler C3-430 Montageanleitung

Kohler

Kohler K-9511 Bedienungsanleitung

Kohler

Kohler K-5814 Montageanleitung

Kohler

Kohler Clearflo K-7147 Bedienungsanleitung

Kohler

Kohler K-T16113 Bedienungsanleitung

Kohler

Kohler K-T8230 Bedienungsanleitung

Kohler

Kohler K-170 Montageanleitung

Kohler

Kohler K-4107T Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung