Kohler WaterTile K-8030 Bedienungsanleitung

Installation Guide

Overhead Rain Shower

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-8030 K-8031

1057619-2-D

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Inspect the supply piping for damage. Replace as necessary.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Sealant

Tape

• Close or 1-1/2" nipple

• Female fittings

• 1/2" copper tubing

• 2x2's and 2x4's

• Conventional woodworking

tools and materials

Phillips

Screwdriver

Plus:

Note: All nipples and fittings

are 1/2" NPT

5/64" & 3/16"

Hex Wrenches

Socket Wrench with 11 mm or

7/16" Socket and Extension

Masking

Tape

Soldering Supplies

1057619-2-D 2 Kohler Co.

1. Install the Supply Piping – Single Supply

Route the water supply lines.

Use the provided soldering template to construct a pressure

balancing loop; this will ensure proper alignment with the

product.

Assemble the pressure balancing loop with a tee positioned over

each of the four raised locations on the soldering template.

Solder the assembly while it is still attached to the soldering

template.

Remove the pressure balancing loop assembly from the soldering

template.

Connect the pressure balancing loop to the water supply.

Do not strap the pipes.

Temporarily install a nipple to each tee. Do not use any sealant.

1/2" NPT Nipple

(12.7 cm)

5" (12.7 cm)

Soldering Template

Pressure

Balancing Loop

Pressure

Balancing Loop

Soldering

Template

Kohler Co. 3 1057619-2-D

2. Install the Supply Piping – Multiple Supplies

Route the water supply lines.

Use the provided soldering template to construct the pressure

balancing loops.

Assemble the pressure balancing loop with a tee positioned over

each of the four raised locations on the soldering template.

Solder the assembly while it is still attached to the soldering

template.

IMPORTANT! To maintain proper positioning of the tees and

ensure alignment with the product, the two pressure balancing loops

must be rigidly connected to each other while still on the soldering

template.

While still on the soldering template, rigidly connect the two

pressure balancing loops to each other.

Remove the pressure balancing loop assembly from the soldering

template.

Connect the pressure balancing loop to the water supply.

1/2" NPT Nipple

Pressure

Balancing

Loops

Soldering

Template

(12.7 cm)

5" (12.7 cm)

Soldering Template

Rigidly connect the loops to each

other, while on the template.

1057619-2-D 4 Kohler Co.

Install the Supply Piping – Multiple Supplies (cont.)

Do not strap the pipes.

Temporarily install a nipple to each tee. Do not use any sealant.

Kohler Co. 5 1057619-2-D

3. Install the Support Framing

Construct the support framing as shown in the illustration above.

The 2x2 should be offset 1-3/16″(3 cm) from the edges of the

2x4’s to support the pressure balancing assembly at the proper

depth.

Install the support framing under the pressure balancing loop(s)

as illustrated. The face of each of the 2x4’s should be installed

ﬂush with the face of each of the ceiling joists.

Do not strap the pipes.

14-1/2"

(36.8 cm)

Typical

1-3/16"

(3 cm)

Pressure

Balancing

Loop Existing

Ceiling

Joist

Existing

Ceiling

Joist

Existing

Ceiling

Joist

2x2

2x4

2x2

2x4

9" (22.9 cm)

1057619-2-D 6 Kohler Co.

4. Install the Finished Ceiling

Install the water-resistant wall board.

Cut out a 9″(22.9 cm) to 9-1/4″(23.5 cm) square at the desired

installation location.

Install the ﬁnished ceiling material.

5. Install the Pipe Nipple

Remove the nipples.

NOTE: The minimum distance between the face of the tees/elbows

and the surface of the ﬁnished ceiling should be 2-1/4″(5.7 cm). The

measurement for typical installations is 2-3/4″(7 cm).

Measure the distance from the face of the tees/elbows to the

surface of the ﬁnished ceiling. Make any adjustments as needed.

If your measurement is 2-1/4″(5.7 cm): Use close pipe nipples.

If your measurement is 2-3/4″(7 cm): Use 1-1/2″pipe nipples.

Thread the nipple into the tee/elbow and hand tighten.

Finished

Ceiling

(22.9 cm) -

9-1/4"

(23.5 cm)

(22.9 cm) -

9-1/4"

(23.5 cm)

2-1/4"

(5.7 cm)

Min

Cutout

Finished Ceiling

Tee

Nipple

Cutout

9" (22.9 cm) -

9-1/4" (23.5 cm)

Kohler Co. 7 1057619-2-D

Install the Pipe Nipple (cont.)

Measure the distance from the end of the nipples to the surface of

the ﬁnished ceiling. Verify that the distance is at least 1-1/2″(3.8

cm) and no more than 1-3/4″(4.4 cm).

Remove the nipples.

Apply thread sealant to the threads of the nipples.

Reinstall the nipples to the tees/elbows.

Run water through the system to ﬂush out any dirt or debris.

1057619-2-D 8 Kohler Co.

6. Install the Waterway

Insert the escutcheon into the rough opening. The double ribs of

the leak shields should be facing up.

If any of the leak shields makes contact with an elbow: Enlarge

the hole in the back of the leak shield to 1-1/4″(3.2 cm).

Thread the adapter onto one of the nipples using the provided 11

mm bit, 11 mm or 7/16″socket, extension and socket wrench. Use

masking tape to hold the bit in place, as the bit could fall off and

cause damage.

IMPORTANT! The escutcheon should sit loosely at this point. If it is

tight against the wall, use a longer pipe nipple.

Align the groove in the waterway with the double ribs on the

leak shield.

Press the waterway into place over the adapter. Secure the

waterway to the adapter with the screw provided.

Verify that the escutcheon does not turn or shift.

Waterway

Screw

Leak Shield Escutcheon

Adapter

Extension

Socket Wrench

With Bit

Kohler Co. 9 1057619-2-D

Install the Waterway (cont.)

IMPORTANT! If the escutcheon is still loose after this step, use a

shorter pipe nipple.

Repeat for the remaining waterways.

1057619-2-D 10 Kohler Co.

Andere Handbücher für WaterTile K-8030

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-T5323 Montageanleitung

Kohler

Kohler K-77364M-AS Bedienungsanleitung

Kohler

Kohler K-9436 Bedienungsanleitung

Kohler

Kohler STRAYT 45370T-B4 Bedienungsanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler KUMIN 99474T-C4 Bedienungsanleitung

Kohler

Kohler K-8724 Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-T13141 Montageanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler K-13491 Montageanleitung

Kohler

Kohler 31138T-4 Bedienungsanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler K-T395 Montageanleitung

Kohler

Kohler K-7514 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Kohler

Kohler K-5024-T Bedienungsanleitung

Kohler

Kohler Portrait K-2226 Bedienungsanleitung

Kohler

Kohler MOXIE 99107T Bedienungsanleitung

Kohler

Kohler K-5031 Montageanleitung

Kohler

Kohler K-10958 Bedienungsanleitung

Kohler

Kohler K-T16229 Bedienungsanleitung

Kohler

Kohler K-T14412 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung