Kohler K-7514 Bedienungsanleitung

Installation Guide

Bathroom Sink Faucet

K-7514, K-7515, K-7516,

K-7517, K-7518, K-7519,

K-13460, K-13461, K-13462,

K-13463, K-13466, K-13467,

K-13468, K-13469, K-13472,

K-13473, K-13475, K-13475,

K-45344, K-45345

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1244026-2-A

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the water supply.

This faucet is for use on a single-hole bathroom sink.

For new installations, install the faucet and drain to the sink

before installing the sink.

The faucet shown in this guide may differ from your actual

product. The installation steps still apply.

In order for this faucet to function properly, install the faucet so

the sensor points directly toward the user.

The faucet is rated at3VDC1W.

1-1/4" to 1-1/2"

Hole Bit

1244026-2-A 2 Kohler Co.

1. Faucet Installation

Prepare the Site - AC and Hybrid Models

NOTE: Before drilling the mounting hole, use the following

provisions for proper placement:

A 1-1/4″(32 mm) minimum to 1-1/2″(38 mm) maximum

diameter mounting hole is required.

A minimum distance of 1-3/4″(44 mm) is required between the

back of the spout and the wall to allow access to the screw.

A 1-1/8″(29 mm) maximum distance is required between the

sink bowl edge and the base of the spout.

AAA Battery Operated Models Only

NOTE: When K-13460, K-13461, K-13466 or K-13467 are installed to

drop-in sinks (sinks with the rim above the deck), the maximum

height of the edge of the basin lip is 3/4″(19 mm) and the

maximum distance from the edge of the sink to the front edge of the

faucet is 1/2″(13 mm).

NOTE: When K-13472 or K-13473 are installed to drop-in sinks, the

maximum height of the edge of the basin lip is 1-1/4″(32 mm).

NOTE: Before drilling the mounting hole, use the following

provisions for proper placement:

A 1-1/4″(32 mm) minimum to 1-1/2″(38 mm) maximum

diameter mounting hole is required.

Without Escutcheon

Spout

Stud

O-ring

Rubber Washer

Bracket Nut

Supply Hoses

Kohler Co. 3 1244026-2-A

Faucet Installation (cont.)

A minimum distance of 1-3/4″(44 mm) is required between the

back of the spout and the wall to allow access to the screw.

Install the Faucet

Determine the mounting hole location.

Drill a hole through the mounting surface according to the

surface manufacturer’s instructions.

Install the stud to the underside of the faucet.

Slide the O-ring over the ﬂexible hoses and stud, then seat the

O-ring in the groove on the underside of the spout.

Insert the spout with ﬂexible hoses and stud through the

mounting hole.

From under the sink, slide the rubber washer and bracket onto

the stud.

Thread the nut onto the stud to secure the faucet to the mounting

surface.

1244026-2-A 4 Kohler Co.

2. Supply Connections

Connect the Filter Assembly

Turn on the water and ﬂush water through the supply stops into

a bucket.

Turn off the water.

Remove the ﬁlter assemblies from the supply hoses. Then thread

a ﬁlter assembly onto each supply stop.

Connect the Supplies

For models with two hoses, thread the left supply hose to the

ﬁlter assembly on the hot supply stop and the right supply hose

to the ﬁlter assembly on the cold supply stop.

For models with one hose, thread the supply hose to the ﬁlter

assembly on the supply stop.

Tighten the connections with a small adjustable wrench.

Turn on the water and ﬂush the faucet by activating it.

NOTE: For optimum performance, clean your ﬁlter screens

periodically. Refer to the Maintenance Guide.

Flex Hose

Filter

Assembly

Supply

Stop

Housing

Adapter

Screen

Kohler Co. 5 1244026-2-A

3. Install the Power Supply - Hybrid Models

NOTE: Avoid the area in front of the sensor for 2 minutes after

connections are complete. The sensor will not function correctly if it

is triggered in the ﬁrst 2 minutes. Disconnect and reconnect the

power to reset the sensor.

Mount the Hybrid Energy Cell (HEC) under the counter using

two screws (not supplied).

Connect the HEC to the faucet wire.

Avoid the area in front of the sensor for 2 minutes.

Hybrid Models

Faucet Wire

Deck

Hybrid

Energy

Cell

1244026-2-A 6 Kohler Co.

4. Install the AC Power Supply

Single Faucet Installations

Connect the faucet wire to the AC supply.

Plug the AC supply into the wall outlet.

Secure any excess wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Multiple Faucet Installations

Mount the AC supply under the counter using two (not supplied)

screws. Orient as shown.

Remove the cover.

Connect the faucet wire to the faucet.

If needed, cut and strip the AC supply wires to length.

Connect the stripped ends to the bottom terminal block (TB2) in

the supply box.

AC Gang

Supply

Black

Red

AC Supply

Faucet

Wire

Multiple Faucet

AC Supply

Single Faucet

Kohler Co. 7 1244026-2-A

Install the AC Power Supply (cont.)

NOTE: If a hard wired installation is required, go to the next

installation section.

Plug the AC supply into the wall outlet.

Secure any excess wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

1244026-2-A 8 Kohler Co.

5. Hard Wire Installation - AC Only

WARNING: Risk of electrical shock. Make sure the power

has been disconnected before performing the following

procedures.

Loosen the terminal block screws and remove the wires from the

top terminal block.

Loosen the outside nut of the strain relief and remove the power

cord.

Put the supply wires through the strain relief and connect to the

top terminal block.

NOTE: If a hard wired installation is required, the strain relief may

need to be replaced depending on wire used.

Tighten the nut on the strain relief.

Replace the cover, and install and tighten the ﬁve screws.

Turn on the AC supply power.

Secure any extra wire under the counter.

IMPORTANT! The area in front of the sensor must be free of

objects during the 2 minute learning cycle or the faucet may not

function properly.

Allow 2 minutes for the sensor to cycle through the automatic

sensing distance.

Secure any excess

wire under counter.

Kohler Co. 9 1244026-2-A

6. Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. Scalding may result if

the temperature limit is set above 120°F (49°C).

NOTE: The water temperature does not need to be adjusted if the

water temperature is below 105°F (41°C).

NOTE: Use a thermometer rated for 120°F (49°C) or greater.

NOTE: When using a tempered water supply, install the

vandal-resistant plug button.

Adjust the Water Temperature Limit – Handle Installations

Turn on the water and adjust to full hot by turning the handle

toward the back of the faucet until it stops.

Determine the temperature using a thermometer. If the

temperature exceeds 105°F (41°C), complete the following steps.

NOTICE: Do not rotate the handle when removing the screw.

Using the 2.5 mm hex wrench provided, remove and retain the

handle screw.

Remove and retain the handle with the spring washer.

Handle

Screw

Vandal-Resistant

Plug Button

Spring

Washer

1244026-2-A 10 Kohler Co.

Andere Handbücher für K-7514

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-14402 Bedienungsanleitung

Kohler

Kohler MINIMA K-45803T-L-SHP Bedienungsanleitung

Kohler

Kohler Torsion Bedienungsanleitung

Kohler

Kohler PURIST UPGRADE Bedienungsanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler HYDRO-TOWER 200 Series Bedienungsanleitung

Kohler

Kohler KELSTON K-2382 Kurzanleitung

Kohler

Kohler ALEO Bedienungsanleitung

Kohler

Kohler STILLNESS Bedienungsanleitung

Kohler

Kohler Stillness K-956 Bedienungsanleitung

Kohler

Kohler Mira Sport Thermostatic 9.8kW 1.1746.006 Bedienungsanleitung

Kohler

Kohler K-7304 Montageanleitung

Kohler

Kohler 8022A Bedienungsanleitung

Kohler

Kohler K-682 Montageanleitung

Kohler

Kohler K-7167 Montageanleitung

Kohler

Kohler K-310 Montageanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler Cantata K-2199 Bedienungsanleitung

Kohler

Kohler Bellhaven K-T11552 Bedienungsanleitung

Kohler

Kohler K-20199 Montageanleitung

Kohler

Kohler K-15182 Bedienungsanleitung

Kohler

Kohler 7098M Bedienungsanleitung

Kohler

Kohler Kelston K-T13494 Montageanleitung

Kohler

Kohler CUFF 37310M-4 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung