Kohler K-3900X-2 Bedienungsanleitung

Installation Guide

Integrated Toilet





1195109-X2-A

English page 1-17



K-3900X-2

1195109-X2-A 2 Kohler Co.

Important Information

IMPORTANT NOTICE TO INSTALLERS!: Please leave these instructions for the consumer. They contain

important information.

NOTE: This product is designed for installation with the electrical and water supplies located through the wall.

Grounding Instructions

• This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the electric current. This product is equipped with a cord having

a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed

and grounded.

WARNING: Risk of electric shock. Improper use of the grounding plug can result in a risk of electric

shock.

• Ifrepairorreplacementofthecordorplugisnecessary,donotconnectthegroundingwiretoeitheratblade

terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the

grounding wire.

• Check with a qualied electrician or service personnel if the grounding instructions are not completely

understood, or if in doubt as to whether the product is properly grounded.

• This product is factory equipped with a specic electric cord and plug to permit connection to a proper

electriccircuit.Makesurethattheproductisconnectedtoanoutlethavingthesamecongurationastheplug.

Noadaptershouldbeusedwiththisproduct.Donotmodifytheplugprovided—ifitwillnotttheoutlet,

have the proper outlet installed by a qualied electrician. If the product must be reconnected for use on

adierenttypeofelectriccircuit,theconnectionshouldbemadebyqualiedservicepersonnel.

Thank You for Choosing Kohler Company

ThankyouforchoosingKohler.Kohlercraftsmanshipoersyouararecombinationofprovenperformance

and graceful sophistication that will satisfy you for years to come. The dependability and beauty of your Kohler

product will surpass your highest expectations. We’re very proud of our products here at Kohler and we know

you will be too.

Please take a few minutes to review this manual before you start installation. If you encounter any installation

or performance problems, please don’t hesitate to contact us. Our phone numbers and website are listed on

back cover.

All information in this manual is based upon the latest product information available at the time of publication.

At Kohler, we constantly strive to improve the quality of our products. We reserve the right to make changes in

product characteristics, packaging or availability at any time without notice.

Thank you for choosing Kohler Company.

Kohler Co. 3 1195109-X2-A

Tools and Materials

Bushings

2 PCS

Caps

2 PCS

#10 x 1-1/2"

Screws

2 PCS

Supply Hose Clip

Mounting Blocks

2 PCS

Remote Control

Docking

Station

5/16" x 2-1/2" Lag Bolts

4 PCS

5/16" Lag Bolt Anchors

4 PCS

Parts Bag Contents

Other Parts

4.5x45DING

Lag Bolts

2 PCS

UX6 x 35

Lag Bolt Anchors

2 PCS

Drill with Assorted Bits Assorted

Screwdrivers

Wax Ring

Shut-off Valve

Universal

Adapter

Floor Flange

Adjustable Wrench

Plus:

• Protective Material

• Tape

Offset Screwdriver

Knife Pencil Pliers Band Tape

Scissors

Floor Flange Accessory Pack

1195109-X2-A 4 Kohler Co.

Before You Begin

WARNING: Risk of electric shock. Disconnect power before servicing.

WARNING: Risk of electric shock. Connect only to a properly-grounded, grounding-type receptacle

which is protected by a 220~240 V, 15 A, 50/60 Hz Ground-Fault Circuit-Interrupter (GFCI) or Earth-

Leakage Circuit-Breaker (ELCB). Do not remove the grounding pin or use a grounding adapter.

CAUTION: Risk of personal injury. This toilet weighs approximately 58 kg. Lift the toilet with two people,

employing proper lifting technique.

CAUTION: Risk of hazardous gases. If a new toilet is not installed immediately, temporarily place a rag

intheoorangeopening.

CAUTION: Risk of product and property damage. This toilet is not intended to be installed in buildings

where temperatures will drop below 1°C. If temperature drops below 0°C, the frozen water in tank could

damage the tank resulting in leaking.

¨Carefully inspect the new toilet for damage.

¨Follow all local plumbing and electrical codes.

Conrmallpartsbelowareincludedbeforebeginningtheinstallation.

Parts Bag Contents

¨(4)5/16″x2-1/2″LagBolts

¨(2)5/16″LagBoltAnchors

¨(2) Mounting Blocks

¨(2) Plastic Caps

¨(2)#10x1-1/2″Screws

¨(2) Bushings

¨(1) Wax Ring

¨(1) Floor Flange

Remote Control Box Contents

¨(1)DockingStation

¨(1) Remote Control

¨(1)DockingStationPowerCord

¨(1) FM Antenna

¨(1) AUX In Cord

¨(2) UX 6 x 35 Lag Bolt Anchors

¨(2) 4.5 x 45 DING Lag Bolts

User Guidelines

¨Homeowner’s Guide

¨Installation Guide

¨Quick Reference Guide

¨Toilet Installation Template

Other Parts

¨(1)SupplyHose

¨(1) Clip

¨(1) Adapter

¨(1)Shut-oValve

¨(1) Floor Flange Accessory Pack

CAUTION: Risk of product damage.Turnonthewaterandallowwatertoowthroughthesupplypipe

toushthesystemofanydebrisbeforeconnectinginletvalve.

Kohler Co. 5 1195109-X2-A

Rough-in - Wall Mount Electrical and Water Supply

NOTICE: The locations for the supply shut-o, electrical outlet, and docking station cord are suggested

locations. Make sure all installations adhere to applicable codes and standards.

NOTICE: Locatingthesupplystopbehindthetoiletwillmakeitdiculttoremovethebackpanel.

IMPORTANT! Donotinstallanyitemsbehindthetoiletthatwillinterferewiththelidwhenitisraised.

All decorative items should be at least 94 cm high to allow clearance for the seat.

¨The remote docking station is equipped with a 5 meter power cord.

¨The supplied power cord is 1422 mm in length. Install the GFCI protected outlet within 1422 mm of the toilet

location.

¨The toilet is equipped with a motion sensor to automatically open the lid when movement is sensed.

SensitivitycanbeadjustedusingtheUserInterface.

¨The toilet is equipped with a motion sensor to automatically open the ring when the light is interrupted.

The sensor is located on the right side of the toilet. This sensor has a maximum range of 20 cm. Keep this area

free of obstructions.

¨1/2″ODcompressionsupplystopoutletisrequiredunlessanadapterisused.

Front of Bowl

654

368

275

Finished Wall

305

336

305

397

920

Power Cord

Reaches

1422

104

151

1041-1676

965 - 1676

230

Remote Dock

454

152 102

203 51

Outlet

GFCI Protected Receptacle

L of Outlet

Side Signal Sensor Field

Front Signal Sensor Field

1/2"

Supply

Dock Power

Cord

Dimensions are approximate.

Unit: mm

1195109-X2-A 6 Kohler Co.

Prepare the Site

NOTE: Locatingthesupplystopbehindthetoiletwillmakeitdiculttoremovethebackpanel.

Install the Dock Power Cord

¨Ifthenishedwallhasnotbeeninstalled,embedthein-wallcableconduittoroutethedockingstationpower

cord. (concealed type)

¨If thenishedwall isinstalled,usethe slotboardcabletoroutethe cord tothe dockingstationlocation.

(out-loading type)

Install the Water Supply

IMPORTANT! Wheninstallingthesupplyhose,connectittothetoiletrst,thenthesupplystop.

NOTE: Thesuppliedwatersupplyhoseis18″(46cm)inlength.Thesuppliedhosemustbeusedforthis

installation.

¨Install the water supply and supply stop.

¨Flush the water supply line into a pail or other container to remove all debris.

Install the Electrical Service

NOTE: Thesuppledpowercordis56″(1420mm)inlength.

¨Locate a dedicated 220~240 V, 50/60 Hz, 15 A or more grounding-type receptacle, protected by a GFCI or

ELCB, within 142 cm of the back of the toilet.

Install External Speaker Wires (optional)

¨If external speakers will be used, install the speaker wires at this time with RCA plug installed at line-end

(not presented).

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

WARNING: Risk of electric shock. Connect only to a properly-grounded, grounding-type receptacle

which is protected by a 220~240V, 50/60 Hz Ground-Fault Circuit-Interrupter (GFCI) or Earth-Leakage

Circuit-Breaker (ELCB). Do not remove the grounding pin or use a grounding adapter.

WARNING: Risk of electric shock. For hardwire installations/through-oor electrical supply: Connect

only to a properly-grounded, dedicated circuit protected by an Class A Ground-Fault Circuit-Interrupter

(GFCI) or Earth-Leakage Circuit-Breaker (ELCB).

152

305 mm From

Finished Wall

Recommended,

298 mm Min

203

Supply Stop

GFCI-

Protected

Receptacle

76 mm Max

When Located

Behind Toilet

102

Dock Power

Cord

Floor Flange

Kohler Co. 7 1195109-X2-A

Install the Remote Dock

NOTE: Thedockingstationcomeswitha5metercord.Locatethedockingstationtoallowthedockingcord

to reach the toilet.

¨Unpack the box containing the remote control components.

¨Removethesmallscrewontheboomofthedockingstation.

¨Carefully remove the cover plate by plug the tool into the gap on the top of the back, gently prying the sides

of the cover plate out until they disconnect from the dock. (see Fig. #2)

¨Carefully disconnect the cover plate plug.

¨Tape the screw to the cover plate and set it aside.

¨For installations using the concealed type, route the power cord through the back cord opening.

¨Forinstallationsusingtheout-loadingtype,routethepowercordthroughtheboomcordopening.

¨Position the docking station in the installation position and mark the screw locations using the dock as

a template.

¨Drill appropriate size mounting holes at the screw mounting locations. The size of the hole will depend

on the need for wall anchors, wall material, and installation requirements.

¨Looseneachofthevesmallscrewslocatedwherethewireswillbeconnected.

¨Run the power cord into the docking station through the back cord opening in concealed type or the

boomcordopeninginout-loadingtype.

¨Position the docking station over the installation location, connect the docking station to the wall using two

screws.

¨Cut the tin (about 2 mm) of the bare end of the wire.

¨Slidethebareendofthewiresintothecorrectport(seeFig.#3)accordingtothecolorandtighteneachscrew

to secure the wires in place, connect the cover plate plug.

¨Snapthecoverplatebackintoplace.

¨Remove the screw and tape from the cover plate and secure the cover plate with the screw to the docking

station.

Holes

Red

Blue

White

Black

Orange

ScrewFig.#1 Fig.#2

Fig.#3 Fig.#4

Connector

Harness

Docking Cord

Back Cord

Opening

Bottom Cord

Opening

Back Cord

Opening

Disconnect.

1195109-X2-A 8 Kohler Co.

Prepare the Installation Location

IMPORTANT! Risk of product damage.IfthereareT-boltsextendingfromtheange,removethem.T-bolts

are not required for this installation.

IMPORTANT! Becauseoftheuniquedesignofthistoilet,thewidthoftheboomedgesofthetoiletwillvary.

The following steps are required because of this variation.

¨Cutouttheinsideoftheangeareaonthetemplatealongthedoedline.

¨Positionthetemplatewiththeholepositionedovertheange.Itiscriticalthatthecenterlinesmarkedonthe

templatearecenteredontheange.

¨Securethetemplatetotheoorwithtape.

¨Conrmthetemplateiscorrectlypositionedandcenteredovertheange.

¨Position the toilet on the template. Make sure the front of the base of the toilet is aligned with the markings

on the template.

¨Conrm the left/right position of the toilet left or right so that an equal amount of shaded area is visible

on each side of the template.

¨Directly under the screw holes on each side of the toilet, accurately mark the boom edge of the base.

Themarkshouldintersectthelineslabeled″C″and″A″or″B″oneachsideofthetemplate.

Template

Screw Hole

Center the toilet

on the template.

Top View

Tape

Flange

Flange Centerlines

Kohler Co. 9 1195109-X2-A

Determine Mounting Block Location

NOTE: Thereisasmallamountofbiodegradable,environmentallysafeantifreezeaddedtothetoilettankto

prevent freezing during shipment. When the toilet is tipped forward, a small amount of the antifreeze may run

ontotheoor.Makesuretheoorisprotected.

¨Positionpiecesoftheboxorotherprotectivematerialontheoordirectlyinfrontofthetoilet.

¨Gently tilt the toilet forward until it rests on the front surface.

NOTE: Theinstallationrangeofthemountingblockismarkedonthetemplate.Duetovariancesinthewidth

of the base, the exact location must be determined by the installer.

¨Measurethewidthofthebase,dimension″A″,ontheleftsideofthetoilet.

¨From the mark indicating the outside edge of the base, measure inward and mark dimension ″A″ on the

templatelinesmarked″A″.

¨Drawalineconnectingthemarksoneachofthelineslabeled″A″.

¨Measurethewidthofthebase,dimension″B,″ontherightsideofthetoilet.

¨From the mark indicating the outside edge of the base, measure inward and mark dimension ″B″ on the

templatelinemarked″B″.

¨Drawalineconnectingthemarksoneachofthelineslabeled″B″.

IMPORTANT! Dimension″C″isthedistancebetweentheinsideedgesoftherightandleftbase.Thedistance

between the outside edges of the mounting blocks should be slightly less than dimension ″C″. The distance

between the edge of the outside edge of the mounting block and the inside edge of the base must be 2 mm or less,

or the strength of the mounting block will be compromised.

¨Measuredimension″C″onthetemplate,startingattheinsideline.

¨Position a mounting block in the area indicated on the left side of the template. Align the outside edge of the

mounting blocks with the inside line. Then move parallel 2 mm to the inside.

Outside Edge

of Toilet

Top View

Protective Material Left Installation

Line

Outside Edge

of Base

1195109-X2-A 10 Kohler Co.

¨Insert a pencil into the holes in the mounting blocks and mark the center of the holes after positioning the

mounting block.

¨Remove the mounting blocks.

¨Position a mounting block in the area indicated on the right side of the template. Align the outside edge of

the mounting blocks with the inside line. Then move parallel 2 mm to the inside.

¨Insert a pencil into the holes in the mounting blocks and mark the center of the holes after positioning the

mounting block.

¨At the locations where the centerline in the slots marked on the template and the pencil mark indicating

the hole locations meet, drill a 13 mm hole if anchors will be used.

¨If anchors will be used, insert one of the supplied anchors in each of the holes.

¨Remove the template.

Determine Mounting Block Location (cont.)

¨ Positionoorangeontheoor.Markthreeanchorholesontheoorwithpencil.

¨Drill 10 mm anchor holes. Insert the anchors.

¨ Placethegasketundertheoorange.Positionoorangeontheoor.

¨Tighten the screws.

Install the Floor Flange

Gasket

Floor Flange

Andere Handbücher für K-3900X-2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Toilette Handbücher

Kohler

Kohler New Wellworth K-3998T-W Bedienungsanleitung

Kohler

Kohler REVE K-24766T-S Bedienungsanleitung

Kohler

Kohler STERLING 402024 Bedienungsanleitung

Kohler

Kohler FLEUR WATERGUARD K-3417 AA Series Bedienungsanleitung

Kohler

Kohler C3-325 Bedienungsanleitung

Kohler

Kohler BRAZN K-EX22381T-SL Bedienungsanleitung

Kohler

Kohler K-3639 Montageanleitung

Kohler

Kohler MODERN LIFE K-77739T-TFSL Bedienungsanleitung

Kohler

Kohler Touchless Flush Montageanleitung

Kohler

Kohler K-11844 Montageanleitung

Kohler

Kohler Cimarron Comfort Height K-31588-0 Bedienungsanleitung

Kohler

Kohler K-3496 Montageanleitung

Kohler

Kohler K-3323 Montageanleitung

Kohler

Kohler K-3488 Montageanleitung

Kohler

Kohler K-3384 Montageanleitung

Kohler

Kohler K-4026T Bedienungsanleitung

Kohler

Kohler VEIL K-5402A-0 Bedienungsanleitung

Kohler

Kohler Highline K-4405 Bedienungsanleitung

Kohler

Kohler S-TRAP K-3869T Bedienungsanleitung

Kohler

Kohler HARKEN K-22695T-S Bedienungsanleitung

Kohler

Kohler Novita BD-N450US Montageanleitung

Kohler

Kohler K-23188X-C Montageanleitung

Kohler

Kohler STERLING Bedienungsanleitung

Kohler

Kohler SAN SOUCI K-21865T-HC Bedienungsanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung