Kohler PURIST K-3492K Bedienungsanleitung

·We appreciate your commitment to Kohler quality. Please

take a few minutes to review this manual before you start

installation. If you encounter any installation or

performance problems, please don t hesitate to contact us.

Our phone numbers and website are listed on the back

cover. Thanks again for choosing Kohler Company.

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

NOTES

DANGER: Risk of electric shock.

WARNING: Risk of electric shock.

CAUTION: Risk of hazardous gases.

NOTICE: Follow all local plumbing and electrical codes.

NOTICE:

WARNING: Risk of electric shock for handwire

installations/through-floor electrical supply:

Disconnect power

before servicing.

Connect only to

circuits protected by Ground-Fault Circuit-Interrupters

(GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

If a new toilet

is not installed immediately, temporarily place a rag in

the floor flange opening.

Receptacles installed in bathrooms to be located at

least 1 meter from a bathtub or shower if practical, but in no

case less than 500 mm.

Observe all local plumbing and building codes.

Carefully inspect the new toilet for damage.

Water and electrical supplies may be wall or floor

mounted. Floor mount supplies are recommended for a

more aesthetic look.

There is a wiring schematic on inside of the of the junction

box cover.

Connect

only to properly-grounded, dedicated 220 VAC, 15A,

50Hz circuit protected by a Class A Ground-Fault

Circuit-Interrupter (GFCI) or Earth-Leakage Circuit-

Breaker (ELCB).

ORDERING INFORMATION

PURIST Toilet.............................................................K-3492K

GFCI ELCB

500

220V 15 50

K-3492K.............................................................

PURIST

INSTALLATION INSTRUCTIONS

TOILET

K-3492K

, 2006

1061926-T01-A

106 2 324 200131

TOOLS AND MATERIALS REQUIRED (Not

supplied)

Adjustable Wrench

Tape measure

Masking tape

Knife

Supply stop(with filter)

Assorted screwdrivers

Plastic anchor

Screw

Fig.#1

Unit: mm

Wall

300

305

184

625

422

359

305

168

403

184

111

Front of Bowl

Supply Stop (with filter)

()

of Outlet

GFCI-Protected Receptacle(water proof)

Floor Flange

T-Bolts

Maximum Height

Both the electrical and water supplies

can be installed on either the wall or

the floor. Follow the information for

your particular installation.

Supply Stop

9.5 Compression Supply

Hardwire Electrical Supply

Note:

Plastic Anchor: Recommend use outside dia 10mm.

Screw: Recommend use M6 screw match the plastic anchor.

10mm

1061926-T01-A

Fig.#2

Remove old gasket from the floor and

closet flange with a putty knife.

Remove old T-bolts and discard them.

if a new toilet is not installed

immediately, temporarily stuff a rag in

the closet flange.

NOTICE:

Closet Flange

B. Roughing-In

DANGER: Risk of electric shock.

NOTE:

WARNING: Risk of electric shock.

Disconnect power

before servicing.

This product is designed to work with either wall or

floor mounted electrical and water supplies. Both types are

shown in the rough-in art.

Connect only to

circuits protected by Ground-Fault Circuit-Interrupters

(GFCI s) or Earth-Leakage Circuit-Breakers (ELCB s).

When the electrical supply is mounted on the wall, a GFCI or

ELCB protected and water proof receptacle is required.

Follow the dimensional information exactly when installing a

hardwire electrical supply.

(GFCI) (ELCB)

(GFCI)

(ELCB)

A. To Remove Existing Toilet

Turn off the water supply. Flush the toilet, and use a sponge

to remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present), and remove

the old tank and bowl.

INSTALLATION

C. Install the T-Bolts

Install two new 8mm (5/16") diameter

T-bolts into the floor flange.

Do not use white cement or high lime

content cements to install this toilet.

The expansion of cement due to a rise

in temperature may make the toilet

crack or cause damage. Kohler is not

responsible for any damage caused by

installation with the use of cement.

C. T

8mm T(5/16")

Fig.#3

T-Bolts

Floor Flange

1061926-T01-A

D. Install the Wax Ring

Place the wax ring in the putty ring

located on the tank.

E. Position the Tank

Remove the outlet gasket.

Mark the centerline on the floor.

Align the tank over the floor flange.

Lower the tank onto the floor flange. The T-bolts should align

with the mounting slots in the base of the tank.

Carefully align the tank on the centerline.

Position the tank on the T-bolts.

Do not push

down on any part of the tank assembly other than the

cylinder. Damage may occur.

Press down on the cylinder where the gasket was mounted.

Do not press anywhere else on the tank

Assembly.

Do not rock or

lift the tank after placement. The seal created by the

wax ring may be broken, resulting in leaking.

Replace the gasket.

Position the loose end of the refill tube in the outlet ring.

CAUTION: Risk of product damage.

Fig.#4

Remove outlet gasket.

Tank

Replace outlet gasket.

Refill Tube

T-Bolts

Floor Flange

Centerlines

Outlet Ring Press here on cylinder.

1061926-T01-A

F. Secure the Tank

CAUTION: Risk of product

damage. Do not overtighten

the mounting nuts. Do not

shorten the T-bolts.

Place a washer on each T-bolt.

Thread a nut onto each T-bolt.

Hand tighten the nuts.

G. Connect the Water

IMPORTANT! If this installation

replaces an existing toilet, a hose

other than the one shipped with the

water supply may be used. Use a

stainless steel, burst-resistant hose.

Connect the water.

Open the shut-off valve.

Fig.#5

Nut

Washer

T-Bolt

Base of

Tank Unit

Fig.#6

H. Check the Waterline

NOTE:

IMPORTANT!

The waterline is a notch in the inside of the tank,

marked with a label.

Turn on the water supply.

Open the motorized valve by sliding the lever back into the

open position.

Verify the inlet valve is set to the correct waterline. Adjust if

needed.

To adjust the inlet valve, use a flathead screwdriver to gently

turn the adjustment rod counterclockwise to lower and

clockwise to raise the inlet valve setting.

The valve will not operate if the valve is locked.

Return the lever back into the unlocked position.

Fig.#7

Waterline

Adjust waterline

Locked

Unlocked

-5-

Flexible Hose

Floor Supply Shown

1061926-T01-A

I. Install the Collar

Place the wiring harness plug, level switch wire, and refill

tube on the floor so they extend out the rear access opening.

Tape them to the floor so they will not be pinched or damaged.

Install the collar onto the tank.

Clip the spray shield into place over the fill valve.

J. Install the Vitreous Shell

WARNING: Risk of personal

injury.

CAUTION: Risk of product

damage.

The vitreous shell

weighs 80 lbs. (36 kg). Use

proper lifting technique when

handling the vitreous shell.

Do not set the shell

down hard. Gently lift and move

the shell if it is not placed

correctly. If handled harshly, the

shell may chip or break.

Carefully pick up the vitreous shell and

place it over the tank.

Make sure the trapway seats fully in

the outlet gasket. If the vitreous shell

does not sit evenly on the floor, the

trapway is not properly seated.

Make all adjustments gently until the

trapway is properly seated.

80 36

Fig.#8

Wiring Harness Plug

Tape

Refill Tube

Level Switch Wire

Centerline Electrical Plug

Collar

Spray Shield

Tank

Vitreous

Collar

Tank

Fig.#9

-6-

1061926-T01-A

L. Check Operation

NOTE:

The flushing mechanism works

best if it is quickly tapped, not held

down for an extended period of time.

There is an approximate eight-

second delay between the flush and

the tank refilling.

Flush the toilet and check for proper

operation.

Refer to the troubleshooting chart if the

toilet does not function properly.

K. Connect the Wiring

WARNING: Risk of personal injury. Make sure the

plug (if plug-in connection is used) and receptacle are

dry. If any moisture is present, allow the area to dry

before plugging the unit in.

If plug-in connection is desired, plug the pump in.

Connect the refill tube.

Connect the wiring harness.

Connect the level switch.

(

)

Level Switch

Refill Tube

Wiring Harness

Fig.#10

Fig.#11

Push to Flush.

-7-

1061926-T01-A

N. Install the Seat

Position a bolt and washer through each of the three holes in

the toilet seat hinge.

Position the gasket on the bolts from the underside of the

hinge.

Place a plastic tapered bushing, tapered-side-down, on each

of the bolts.

Place an expansion sleeve on each bolt.

Thread a brass tapered bushing, tapered-side-up, onto each

bolt. Do not tighten at this time.

Position the seat on the toilet and align the bolts with the toilet

seat mounting holes.

Insert the bolts and sleeves into the holes.

Use a flat blade screwdriver to thread the bolts until they are

snug, but do not fully tighten at this time.

Lower the seat and check seat alignment.

Align the seat on the toilet and then carefully raise the seat to

expose the bolts.

Tighten the bolts. Do not overtighten.

Position the tab on the hinge cover with the slot in the hinge

assembly and snap the hinge cover into place.

With the seat raised, gently push the seat cover forward. The

seat and seat cover should close Slowly.

M. Secure the Vitreous Shell

CAUTION: Risk of product

damage. Do not overtighten the

screws when tightening. The

vitreous shell may chip or break

if the screws are overtightened.

Insert a screw through both grommets.

Insert a screw in both of the provided

holes and tighten. Do not overtighten.

Place a cap over each screw. The

caps should be flush with the exterior

of the shell.

Screw

Cap

Grommet

Fig.#12

Fig.#13

Hinge Cover

Hinge Cover Tab

Hinge Slot

Cover/Seat

Bolt

Washer

Plastic Tapered Bushing

Brass Tapered Bushing

Toilet

Hinge

Gasket

Expansion Sleeve

Toilet Seat Mounting Hole

-8-

1061926-T01-A

NOTE: Do not caulk the access cover to the floor.

If this installation uses wall mounted electrical or water

supplies, cut a recess in the access cover using a utility knife

at the spot marked on the access cover.

Place the access cover over the opening in the back of the

toilet.

Caulk around the base of toilet. Do not caulk the area where

the access cover meets the floor.

Fig.#14

Access

Opening

Caulk Base Of Toilet.

Toilet Back

Do Not Caulk Base Of Access Cover.

Cut With Utility Knife.

Access Cover

COMPLETE THE INSTALLATION

-9-

1061926-T01-A

-10-

SYMPTOMS PROBABLE CAUSES RECORRECTIVE ACTION

TROUBLESHOOTING

1. The toilet does not

flush.

A. Various. A. Perform the troubleshooting steps below.

2. The toilet randomly

flushes 2 Times.

A. The tank is overfilling. A. Immediately perform the troubleshooting steps or

turn the water off. Turn the water back on when

troubleshooting.

3. The toilet flushes 3

times, then

operates normally.

A. The fill valve is not turning off.

B. The motorized valve is not Closing.

A. Repair or replace the fill valve.

B. Repair or replace the motorized valve.

4. The toilet flushes 5

times.

A. The level switch has an intermittent connection.

B. The level switch is stuck in the up position.

C. The level switch is not properly connected.

D. The level switch does not move Freely.

A. Repair of replace the level Switch.

B. Repair or replace the level Switch.

C. Reconnect the level switch Properly.

D. Replace the level switch.

5. The toilet fails to

operate.

A. There is a problem with the Wiring.

B. The GFCI or ELCB is tripped.

C. There is a problem with the pump connection.

D. The actuation switch is not properly connected.

E. The level switch is not properly connected.

F. The pump assembly does not Work.

G. The actuation assembly does not work.

A. Check the wiring and connect the power.

B. Reset the GFCI or ELCB (if Applicable).

C. Check the pump connection.

D. Check the actuation switch Connection.

E. Check the level switch Connection.

F. Replace the pump assembly.

G. Replace the actuation assembly.

This troubleshooting guide is for general aid only. A Kohler Authorized Service Representative or qualified electrician should

correct all electrical problems. For warranty service, contact your dealer or wholesale Distributor.

To troubleshoot this toilet you must first:

IMPORTANT!

Unplug the toilet or turn off the power.

If needed, turn on the water supply.

Plug the toilet back in or turn the power back on.

When the power is turned on, the toilet may flush three times and then function correctly.

No action is needed if this happens.

Note the results (how many times the toilet flushes, whether it operates normally).

Consult the chart below. Perform the recommended action.

1061926-T01-A

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler K-3422 Bedienungsanleitung

Kohler

Kohler SAN SOUCI K-21865T-ITHC2 Bedienungsanleitung

Kohler

Kohler K-30215T-S Bedienungsanleitung

Kohler

Kohler K-11889 Montageanleitung

Kohler

Kohler K-29777-PA-0 Montageanleitung

Kohler

Kohler REVIVAL K-14241 Bedienungsanleitung

Kohler

Kohler S-TRAP K-23188T-ITHC Bedienungsanleitung

Kohler

Kohler K-3589 Montageanleitung

Kohler

Kohler K-3434-X Bedienungsanleitung

Kohler

Kohler K-5889X Montageanleitung

Kohler

Kohler Escale K-25091T-S Bedienungsanleitung

Kohler

Kohler Veil K-5402T Bedienungsanleitung

Kohler

Kohler REVIVAL Bedienungsanleitung

Kohler

Kohler K-3496 Bedienungsanleitung

Kohler

Kohler K-3797 Montageanleitung

Kohler

Kohler C3-400 Montageanleitung

Kohler

Kohler K-22241K Montageanleitung

Kohler

Kohler Stanwell K-4972-ER Bedienungsanleitung

Kohler

Kohler EIR Montageanleitung

Kohler

Kohler C3-225 Bedienungsanleitung

Kohler

Kohler TRESHAM K-3854T Bedienungsanleitung

Kohler

Kohler K-6300 Montageanleitung

Kohler

Kohler Quiet-Close C3-455 Bedienungsanleitung

Kohler

Kohler Inodoro K-3517 Montageanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung