Kohler VEIL K-1381T-HC Bedienungsanleitung

VEIL

INSTALLATION INSTRUCTIONS

3.0/4.5L CLASS FIVE 1PC TOILET (W/O SEAT)

3.0/4.5L ( )

S-TRAP 305mm K-1381T-HC

S-TRAP 400mm K-1382T-HC

-1-

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation. This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information -

please leave instructions for the

consumer

·-

NOTES

Observe all local plumbing and building codes.

Shut off the water supply.

Seat post holes are on 140mm (5-1/2") centers.

Ensure that the new drain has the correct roughing-in

dimension. This toilet has a 305mm /400mm roughing-in

dimension. .

Closet flange must be 305mm/400mm on-center from wall.

Carefully inspect the new fixture for any sign of damage.

For new construction, refer to the dimensions in

for locating the shut-off valve.

Fixture dimensions are nominal and conform to tolerances

established by ASME Standards (A112.19.2-2018).

See Fig. #1

Fig. #1

and Fig. #3

The product complies with Q/KCI-006-2018.

140mm

305mm/400mm( 1)

305mm/400mm

ASME A112.19.2-

2018

Q/KCI-006-2018

3.0/4.5L

( )305mm .................................................K-1381T-HC

3.0/4.5L

( )400mm .................................................K-1382T-HC

ORDERING INFORMATION

VEIL 3.0/4.5L Class Five 1PC Toilet

(W/O Seat) 305mm...............................................K-1381T-HC

VEIL 3.0/4.5L Class Five 1PC Toilet

(W/O Seat) 400mm...............................................K-1382T-HC

2019

No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137

2 528137

8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA 256410

8 256410

NO.1 KOHLER STREET, ECONOMIC DEVELOPMENT ZONE OF FAKU COUNTY, SHENYANG LIAONING PROVINCE, PRC 110400

1 110400

POST CODE:

1326266-T01-B

WARNING: Risk of personal injury or product

damage

WARNING: Risk of external leakage

: Handle vitreous china products very carefully.

Vitreous china can break and chip if you overtighten

bolts and nuts.

. The fill valve

nut has been factory-tightened to design specifications.

If re-tightening is required, wrench tighten one turn

past finger tight .

-2-

TOOLS AND MATERIALS REQUIRED (Not

supplied)

254mm (10") adjustable wrench

305mm (12") pipe wrench

Metal file (file cut)

Tape measure

Tubing cutter

Level

Hacksaw

Putty knife

Screwdriver

Toilet gasket (wax seal)

Toilet T-bolts (2), 8mm (5/16") diameter

Toilet supply shut-off valve, 10mm(3/8 ) recommended

If the existing toilet does not have a supply shut-off

valve below the tank, install one before installing the new

toilet.

NOTICE:

254mm

305mm

8mm T 2

10mm

Fig.#1

Unit: mm

Kohler reserves the right to change marked dimensions without prior notice.

Reference Value

Finished

Wall

305/400

393

725

387

280 320

375 225

311

692

200

190

1326266-T01-B

-3-

Fig.#2

Remove the old gasket from the floor

and the closet flange with a putty knife.

Remove the old T-bolts and discard

them.

if the new toilet is not

installed immediately, temporarily stuff

a rag into the closet flange.

NOTICE:

NOTICE: Do not use white cement or high lime content

cements to install this toilet. The expansion of cement due to

a rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage caused by

installation with the use of cement.

Closet Flange

67mm;

200mm

190

Fig.#3

Fig.#4

Fig.#5

TO INSTALL SUPPLY

SHUT-OFF VALVE

Install the supply shut-off valve so it is

200mm above the finished floor line,

and 190mm to the left of the closet

flange centerline.

The centerline of the supply shut-off

valve outlet should extend 67mm from

the finished wall. Install the supply

shut-off valve with the outlet vertical.

Supply Shut-Off Valve

Closet Flange

Centerline

190

305

200

10mm

TO INSTALL BOWL

Position the template and align with

drain hole.

Mark down the position of foot and 5

holes.

Drill holes on ground with the drill of

10mm (3/8"), then insert anchor to

holes.

Please make sure there is

no water pipe or spool under the 5

holes to be drilled.

CAUTION:

Drain Hole

3/8

10mm

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a sponge

to remove the remaining water from the tank and bowl.

Disconnect the supply shut-off valve (if present), and remove

the old tank and bowl.

()

INSTALLATION

1326266-T01-B

Fig.#7

Fig.#8

Fig.#9

Fig.#10

Firmly press the toilet gasket onto the

toilet outlet of plastic trap.

Wax ring type toilet gasket

should not be installed at temperatures

less than 21 C.

If you are using a toilet

gasket with an integral plastic sleeve,

make sure the gasket is positioned

with the sleeve facing away from the

toilet.

NOTE 1:

NOTE 2:

Install plastic to ground and mounted

with 3 set of bolts firmly.

Carefully align and lower the bowl.

Apply weight to the bowl rim to let the

outlet insert into plastic trap.

Carefully thread the screws into the

brackets, until toilet is secure.

Alternately tighten left and right sides

to prevent pulling the toilet off center.

Install cap to cover screw.

Do not overtighten.

-4-

Fig.#6

Install brackets.

Plastic Trap Outlet

Toilet Gasket

Outlet

Plastic Trap

Cap Screw Bushing

1326266-T01-B

-5-

Fig.#11

Apply caulk around base.

IMPORTANT:

Make certain the top is turned to the locked

position. Valve may not turn on if top is not fully in the

locked position.

Before turning on the supply valve for the first

time, follow the steps below to clear sand, debris and rust

from the system:

Make sure water sure water supply is off. Remove valve END

by rotating it 1/8 turn counterclockwise.

While holding a container over the uncapped VALVE to

prevent splashing, turn water supply on and off a few times.

Leave water supply off.

Replace END by engaging lugs and rotating 1/8 turn

clockwise.

Turn on water supply. Check that water level is at the marked

water line.

1/8

TO CONNECT WATER

SUPPLY

* Flexible hose (not provided) are

recommended to connect the supply

line to the fill valve. If you use a rigid

connection(not provided), take care

not to apply side forces to the bottom

of the fill valve. Be sure the rigid

connection must be fit with supply line

completely to prevent damage shank

by forced connection.

*()

()

Supply Shank*

Supply Shut-Off Valve

Fig.#12

Fig.#13

Install the tank lid and the seat.

Tighten the seat power line and pipe

with mounting twist tie.

Periodically check for leaks for several

days following the installation.

1326266-T01-B

SYMPTOMS

A. Adjust flapper chain assembly for proper slack.

B. Inspect, clean and, if necessary, replace

flapper ball and/or seat.

PROBABLE CAUSES CORRECTIVE ACTION

1. Fill valve turns on/off by

itself without toilet being

flushed.

A. No slack in flapper chain assembly, holding

flapper off seat.

B. Flush valve flapper ball worn, dirty or

misaligned with flush valve seat; or seat

corroded so flapper will not seal.

A. During fill cycle, hold float under water a few

seconds to allow it to fill with water ballast.

B. Adjust the cross-shaped thread on float rod

until water level is at marked water line.

A. Valve float cup does not contain enough water

to provide required ballast.

B. Float height incorrect.

4. Long or noisy tank fill

cycle.

A. Perform Corrective Action 2.A.A. Plugged valve inlet or supply line.

A. Adjust tank water level.

B. Unclog trapway; clean rim holes.

C. Clear obstruction from soil pipe or vent.

D. Open supply shut-off valve.

A. Water level is too low.

B. Trapway or rim holes are obstructed.

C. Soil pipe or vent is obstructed.

D. Supply shut-off valve not fully open.

5. Poor flush.

A. Toilet trapway is obstructed.

B. Soil pipe or vent is obstructed.

A. Use plunger to unclog.

B. Clear obstruction from soil pipe or vent pipe.

6. Toilet overflows.

2. Fill valve continues to

run, allowing water to

enter tank.

3. Incorrect water level

height.

FILL FLOAT WITH

BALLAST

Adjust the float by the cross-shaped

thread and sliding it up or down on the

float rod until the water level is at the

marked water line.

Test flush the toilet.

Check all connections for leakage for

several days.

Set the tank cover in place on the tank.

Fig.#14

A. Foreign particles lodged under the float valve

seal (located under fill valve cap).

B. Fill valve seal (located under float valve cap)

may be cracked or split.

C. Tank water level set above overflow level.

D. Water leaking past flush ball.

E. Trip lever binding, holding flush ball open.

A. Shut off water supply; remove fill valve cap

assembly by rotating 1/8 turn counterclockwise.

Cover uncapped lower valve unit with an

inverted cup (holding it to prevent overspray),

and turn water on and off a few times. Clean

fill valve seal surface (located under float valve

cap). Replace fill valve cap assembly by

engaging lugs and rotating 1/8 turn clockwise.

Turn water on. Install filter in supply line to

prevent recurring problems.

B. Replace seal.

C. During fill cycle, hold float under water a few

seconds to allow it to fill with water ballast.

Adjust float by adjust the cross-shaped thread

on float rod and sliding float up or down on

float rod until water level is at marked water

line.

D. Replace flush ball.

E. Turn trip lever nut clockwise to loosen until trip

lever no longer binds.

-6-

1326266-T01-B

A. (

)

B. ( )

1/8

()

1/8

3. A.

4. A. 2AA.

5. A.

6. A.

-7-

1326266-T01-B

()

CONSUMER RESPONSIBILITIES

Clean the outside surfaces of your vitreous china fixture with

mild soap and warm water. Wipe the entire surface

completely dry with a clean, soft cloth. Many cleaners contain

harsh chemicals, such as ammonia, which can damage the

finish. Do not use those cleaners.

If you live in a hard water area, make certain that the holes in

the toilet rim are kept clean to ensure proper bowl flushing.

Toilet bowl cleaners should be used at least once a week.

Use a long-handled brush to clean the rim holes, and to clean

as far into the trap as possible to prevent mineral deposits

from forming.

Most toilet bowl cleaners are not harmful to the vitreous china

surface of the toilet bowl. Please follow the bowl cleaner

manufacturer's instructions carefully.

Do not use abrasive cleaners or solvents.

Do not use in-tank cleaners. Products containing

chlorine (calcium hypochlorite) can seriously damage

fittings in the tank. This damage can cause leakage

and property damage.

Kohler Company shall not be responsible or liable for any

damage to these tank fittings caused by the use of cleaners

containing chlorine (calcium hypochlorite).

WARNING: Risk of property or product damage.

CAUTION: Don t use any cement while installing

the toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damage

the feet of the toilet. Kohler will not be responsible for

any damage because of using cement.

Do not throw into the toilet what is easy to block it,

such as newspaper, paper pilch, sanitary towel.

Do not bump the vitreous china with great force to

prevent it from damaging and leaking.

Do not use the product in the water below 0 C.

Please do not use hard materials (like

scouring pad) to clean product surface, especially the

product logo.

CAUTION:

-8-

1326266-T01-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Toilette Handbücher

Kohler

Kohler K-3451 Bedienungsanleitung

Kohler

Kohler Kallista P70350 Montageanleitung

Kohler

Kohler SAN RAPHAEL GRANDE K-8688T-HC Bedienungsanleitung

Kohler

Kohler K-11899 Montageanleitung

Kohler

Kohler REVE K-24766T-S Bedienungsanleitung

Kohler

Kohler K-11471 Montageanleitung

Kohler

Kohler Reve Comfort Height K-3797-0 Montageanleitung

Kohler

Kohler C3-400 Montageanleitung

Kohler

Kohler Escale K-3588-96 Bedienungsanleitung

Kohler

Kohler ESCALE K-24837T-S Bedienungsanleitung

Kohler

Kohler Memoirs K-724-G96 Bedienungsanleitung

Kohler

Kohler VEIL K-20534T-S Bedienungsanleitung

Kohler

Kohler K-17641 Bedienungsanleitung

Kohler

Kohler K-23188X-C Montageanleitung

Kohler

Kohler ADAIR K-5171T-M Bedienungsanleitung

Kohler

Kohler K-3484 Montageanleitung

Kohler

Kohler FAMILY CARE S-TRAP K-23191T-NS Bedienungsanleitung

Kohler

Kohler PURIST K-3492K Bedienungsanleitung

Kohler

Kohler K-4406X Montageanleitung

Kohler

Kohler ODEON K-8752K-W Bedienungsanleitung

Kohler

Kohler K-4737 Montageanleitung

Kohler

Kohler REACH K-3991T-HC Bedienungsanleitung

Kohler

Kohler K-3608 Montageanleitung

Kohler

Kohler Heated French Curve K-4649 Montageanleitung

Beliebte Toilette Handbücher anderer Marken

Toto

Toto Washlet TCF4911 Series Bedienungsanleitung

Grohe

Grohe Sensia ARENA Bedienungsanleitung

Geberit

Geberit AQUACLEAN MERA CLASSIC Bedienungsanleitung

Better Bathrooms

Better Bathrooms BUN/BeBa 27555/78725 Bedienungsanleitung

American Standard

American Standard CONCEPT Cube TF-2704 Bedienungsanleitung

BIOLAN

BIOLAN ECO Stücklistenhandbuch

Thetford

Thetford C260 Series Bedienungsanleitung

KELISS

KELISS T162A Series Bedienungsanleitung

BIOLAN

BIOLAN GARDEN TOILET Stücklistenhandbuch

washloo

washloo Prestige Bedienungsanleitung

JABSCO

JABSCO 37010 Series Bedienungsanleitung

Olympia

Olympia EPOQUE 69209 Bedienungsanleitung

DENCK

DENCK PURE-D Bedienungsanleitung

Silent Venus

Silent Venus SVP600 Wartungs- und Serviceanleitung

InBe

InBe IB/04.06050 Bedienungsanleitung

Swiss Madison

Swiss Madison Carré SM-1T264 Bedienungsanleitung

agape

agape PEAR 2 Bedienungsanleitung

Roca

Roca DAMA SENSO COMPACT Bedienungsanleitung