Kongskilde 300FL Bedienungsanleitung

ASSEMBLY INSTRUCTIONSRTS

& OPERATING GUIDE

For 300FL Finger Tine Harrow Kit for 300SS Rota Harrows

Kongskilde

300 FL Kit

300FL Harrows

Finger Tine Harrow Kit

INDEX

INTRODUCTION: ................................................................................................................ 3

PRE ASSEMBLY TIPS: ....................................................................................................... 3

Mounting Brackets:............................................................................................................ 4

FL Tine Mounting:...............................................................................................................5

FIELD SETTINGS:............................................................................................................... 6

ADJUSTMENTS / PRECAUTIONS: ................................................................................... 8

MAINTENANCE: ................................................................................................................. 9

INTRODUCTION:

The Kongskilde 300 FL - Finger Tine Harrow Attachment has been developed as a optional

pre-levelling attachment for Kongskilde 300 Series Double Rota-Harrows.

When properly adjusted, the 300 FL Harrow Attachment will help to divide the flow of soil from

thebackrowoftines,thusreducingtheridgesthatforminfrontofthedoublerotaharrows.This

pre-levelling of the soil surface enhances the performance of the double rota-harrows in

preparing a level surface for planting in various field conditions and soil types.

This booklet has been developed to assist you in assembling your 300 FL Harrow Kit for

Kongskilde cultivator equipped with 300 Series Double Rota-Harrows.

PRE ASSEMBLY TIPS:

Priortoassemblingthe300 FLFingerTine Harrows, the cultivator should be carefully unfolded

and lowered to the ground, (resting on the tines), on a flat level area.

The 300 Series - Double Rota-Harrows must be mounted first, according to the instructions

provided in the HarrowAssembly & Operator Manual no. 03 150 109.

We strongly recommend that you do not attempt to assemble the harrows before mounting to

the cultivator, as the harrow sections are heavy and difficult to move when assembled. It is

also difficult to insure correct placement and spacing of the harrow sections if they have been

pre-assembled.

NOTE: Before starting be sure to check that you have all of the correct components in order to

assemble each section of harrows as shown in the parts list booklet and assembly diagrams

provided.

Mounting Brackets:

1. With the Double Rota-Harrows fully assembled and the cultivator laid out on a flat level

area, begin by selecting the locations for the mounting brackets on the front roller frame tube.

2. The location of the mounting brackets will vary from roller to roller depending on the

position of the roller harrow hanger arms and tine locations. Place the mounting brackets at

the best possible location on the roller frame tubes so that they will not interfere with the

placement of the FL finger tines in step 4.

3. After securing the mounting brackets, match the toolbar length to the roller section and

attach the toolbars to the mounting brackets with the wire tine clamps provided. The toolbars

can be shifted a few inches to the right or left of centre as required for correct mounting of the

FL finger tines.

FL Tine Mounting:

4. The Finger Tines must be mounted so that they are being pushed in the direction of

travel as shown below.

5. Position one finger tine about 4" to the right and left of each tine on the back row of the

cultivator. Secure the FL tines to the toolbars with the tine clamps, nuts, bolts and washers

provided.Whencompleted,therewill be 2 FLtinesmountedon the toolbars for every S-tine on

therearbarofthe cultivator.Forfurtherinstructionsonlocating the FLtinesrefer to the section

on field settings.

FIELD SETTINGS:

A) NOTE: There are many factors that can affect the ability of the harrows to level the soil

surfacebehindthe cultivator; Cultivator tinespacing,typeofshares(sweeps), cultivating depth,

ground speed, direction of travel across the field (angle), soil type, and soil conditions like

moisture content and crop residue levels, all have an affect on the quality and levelness of the

seed bed. Therefore, do not expect the same settings to work in every case. Be prepared to

adapt and adjust your equipment and operating practices to obtain the best results for each

field condition.

B) The down pressure on the rota-harrows can be increased or decreased by turning the

spring adjustment bolt with a 15/16" socket wrench. First loosen the jamnut then adjust the

downpressureontherollers as required to break lumps or clods and obtain a levelsoilsurface.

Securethejamnut.(Forfurther instructions on the double rota-harrows refer totheappropriate

section in the 300 SS harrow manual.)

C) For best results, move the FL finger tines from 4" to 8 " to the right or left behind the tines

as required, so that the finger tine divides the flow of soil coming from the rear row of cultivator

S-tines in half, or knocks down the ridge formed in between the tines into 2 smaller ridges. By

pre-levelling the soil in this way the rota harrow has better contact with the entire soil surface

creating a more uniform surface and soil structure for planting.

D) The angle of the FL tines can be adjusted to 4 different positions.The steeper the angle

-the more aggressivethetineactionbecomes. Selection oftheworkinganglewill again depend

onthesoil type and the amountof crop residue left onthe soil from the previousyears harvest.

Field testing has shown that in most cases the best working angle for the FL tines is when the

stop block is located in position 4.

E) Theheightofthe FLtineson eachtoolbarcanbeadjustedto3 differentpositions.Normally

the bracket should be set at the highest position (1) and then lowered to position (2) or (3) as

the finger tines wear. When the tines becomes worn down after position (3) they should be

replaced.

ADJUSTMENTS / PRECAUTIONS:

Whenthe assembly of the harrows has beencompleted check to make sure that thecomplete

assembly appears evenly spaced and centred across the back of the cultivator. If the harrow

assemblyisnotcentredyoumayhavetoshifttheharrowsectionsasrequired.Impropercentring

of the harrows may cause the cultivator to pull crooked in the field.

Check to make sure that each section of harrows can move up and down freely. It is important

that the harrow sections will not hit each other when working on uneven ground.

Check all nuts and bolts and secure if loose.

Takecarewhenfolding thecultivatorfortransport forthefirst timeaftercompletingtheassembly.

Check to make sure that the harrows do not interfere with each other or other cultivator frame

components when folding and unfolding.

DANGER! NEVER STAND OR WORK IN THE AREA BELOW THE WINGS OR

UNDER AN UNSUPPORTED CULTIVATOR FRAME.

ALWAYS USE WING LOCK PINS, AND WHEEL CYLINDER TRANSPORT LOCKS.

USE EXTREME CAUTION WHEN WORKING AROUND HEAVY EQUIPMENT.

BLOCK THE WHEELSAND MAKE SURE THAT THE UNIT IS SUPPORTED TO PREVENT

IT FROM FALLING BEFORE ATTEMPTING TO MAKE ADJUSTMENTS OR WHEN

PERFORMING MAINTENANCE OPERATIONS.

MAINTENANCE:

A) Periodically check all nuts and bolts and secure if loose.

B) Lubricate the G-bearings after every 12 hours of operation. DO NOT OVER GREASE

THE G-BEARING: Over greasing may cause damage to the bearing seals.

C) Periodically check and remove any foreign material that may become wound around the

FL tines, rollers or bearings and remove any objects (ie: stones) that have become trapped in

the rollers. Any bent or damaged roller sections should be repaired or replaced.

D) Replace or repair any bent, broken or very worn down FL tines.

Alwayschecktheconditionofyourfieldcultivatorand levelling attachments at regular intervals

and keep in good repair. Optimal performance cannot be expected of equipment in poor

condition.

603 150 561 NOVEMBER2000

Inhaltsverzeichnis

Andere Kongskilde Landwirtschaftliche Geräte Handbücher

Kongskilde

Kongskilde K 20 C Handbuch

Kongskilde

Kongskilde DPC 40 Handbuch

Kongskilde

Kongskilde FCT 1360 Bedienungsanleitung

Kongskilde

Kongskilde Vibro Crop Series Bedienungsanleitung

Kongskilde

Kongskilde KCT Bedienungsanleitung

Kongskilde

Kongskilde R+ 820 Bedienungsanleitung

Kongskilde

Kongskilde Z 665 HYDRO Bedienungsanleitung

Kongskilde

Kongskilde GXS 2405 P Bedienungsanleitung

Kongskilde

Kongskilde KC Bedienungsanleitung

Kongskilde

Kongskilde R400 Bedienungsanleitung

Kongskilde

Kongskilde CFA 20 Bedienungsanleitung

Kongskilde

Kongskilde KG 10 Bedienungsanleitung

Kongskilde

Kongskilde FK100 Bedienungsanleitung

Kongskilde

Kongskilde R+ 760 Bedienungsanleitung

Kongskilde

Kongskilde R+ 1410 S Bedienungsanleitung

Kongskilde

Kongskilde FRONT TERRA-C Bedienungsanleitung

Kongskilde

Kongskilde R 420 DS Bedienungsanleitung

Kongskilde

Kongskilde R+ 420 Bedienungsanleitung

Kongskilde

Kongskilde DEMETER CLASSIC CS Bedienungsanleitung

Kongskilde

Kongskilde TERRA-D Handbuch

Kongskilde

Kongskilde 800 Series Bedienungsanleitung

Kongskilde

Kongskilde Z 8805 Bedienungsanleitung

Kongskilde

Kongskilde VENTUS 2400 Bedienungsanleitung

Kongskilde

Kongskilde VIBRO TILL 2800 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung