Kongskilde R+ 420 Bedienungsanleitung

ORIGINAL INSTRUCTIONS - according to Directive 2006/42/EC, Annex I 1.7.4.1

Part number 81PIGB-184x

1st edition English

February 2018

R+ 420

R+ 460

Rake

OPERATOR’S MANUAL

PIGB-184X-02 R+420 R+460 0218

FOREWORD

DEAR CUSTOMER!

We appreciate the confidence you have shown to our company by investing in a

KONGSKILDE product and congratulate you with your new purchase. Of course, it is

our wish that you will experience complete satisfaction with the investment.

This instruction manual contains information about correct and safe use of the

machine.

When buying the machine you will receive information about use, adjustment and

maintenance.

However, this first introduction cannot replace a more thorough knowledge of the

different tasks, functions and correct technical use of the machine.

Therefore you should read this instruction manual very carefully before using

the machine. Pay special attention to the safety instructions.

This instruction manual is made so that the information is mentioned in the order you

will need it, i.e. from the necessary operation conditions to use and maintenance.

Besides this there are illustrations with text.

"Right" and "Left" are defined from a position behind the machine facing the direction

of travel.

All the information, illustrations and technical specifications in this instruction manual

describe the latest version at the time of publication.

Kongskilde Industries A/S reserves the right to make changes or improvements in the

design or construction of any part without incurring the obligations to install such

changes on any unit previously delivered.

PIGB-184X-02 R+420 R+460 0218

Contents

1. In general

1.1 Intended use

1.2 Foreseeable misuse

1.3 General safety instructions

1.4 Technical data

1.4.1 Manufacturer’s address

1.4.2 Certificates

1.4.3 Marking of the machine

1.4.4 General technical data

2. Safety

2.1 Marking of safety instructions in the instruction manual

2.2 Safety rules and accident prevention

2.2.1 Power take-off

2.2.2 Tyres

2.2.3 Working near high-voltage lines

2.2.4 Maintenance

2.3 Placement of safety signs on the machine

2.4 Placement of normal reference signs on the machine

3. Mounting of the machine after delivery

3.1 Mounting of PTO drive shaft

3.2 Adjustment of PTO drive shaft

3.3 Mounting of optional equipment “Warning panel with lighting equipment”

3.4 Mounting of optional equipment “Support wheel, adjustable”

3.5 Mounting of optional equipment “4-wheel bogie axle” (R+420)

3.6 Mounting of optional equipment “3D bogie axle” (R+420)

3.7 Functional test

4. Mounting of the rake and preparation

4.1 Special instructions

4.2 Preparation of tractor

4.2.1 3-point suspension on the tractor

4.2.2 Electric system

4.3 Connection of the rotary rake to the tractor

4.3.1 Connection to the link arms of the tractor

4.3.2 Connection of lighting equipment

4.3.3 Connection of PTO shaft

4.4 Disconnection and parking of the rotary rake

4.5 Transport on public road

PIGB-184X-02 R+420 R+460 0218

5. Handling of the rake during working

5.1 Conversion of the rake from transport to working position

5.1.1 Release of the transport lock

5.1.2 Mounting and securing of tine arms

5.1.3 Safety frame is placed in working position

5.1.4 Swath guard is placed in working position

5.2 Starting the rotor

5.3 Conversion of the rake from working to transport position

5.3.1 Dismounting of tine arms

5.3.2 Safety frame is placed in transport position

5.3.3 Swath guard is placed in transport position

5.3.4 Activating the transport lock

5.4 Further instructions for working and driving with the machine

6. Basic adjustment of the rake

6.1 Adjustment of working depth

6.2 Adjustment of the length of the top link

6.3 Adjustment of the rotor inclination in the direction of travel

6.4 Adjustment of the rotor inclination with extra support wheel (option)

6.5 Adjustment of the rotor inclination transverse to the direction of travel

6.6 Adjustment of working width and swath width

6.7 Adjustment of the cam track

6.8 Adjustment of shock absorber

6.9 Working speed and number of revolutions

7. Service and maintenance of the rake

7.1 Safety rules

7.2 General maintenance instructions

7.3 Cleaning of the machine and preparation for winter storage

7.3.1 Cleaning of the machine

7.3.2 Placement of the rake in the open

7.3.3 Winter storage

7.4 Wheels

7.4.1 Tyre pressure

7.5 PTO shafts

7.6 Replacement of bearing tubes

8. Maintenance - grease chart

8.1 PTO shaft

8.2 Rotor gear

8.3 Cam track

8.4 Swivel pin on suspension

8.5 Transport safety bolt

8.6 Universal joint

8.7 Grease chart overview

PIGB-184X-02 R+420 R+460 0218

9. Machine disposal

10. Supplement

11. Warranty

PIGB-184X-02 R+420 R+460 0218

1. In general

This instruction manual contains important information concerning operation,

maintenance and adjustment of the machine. Furthermore, all safety instructions are

mentioned and emphasized. Read the instruction manual carefully before using the

machine. The instruction manual should be accessible for the operator.

All safety instructions must be observed.

1.1 Intended use

The rotary rake is intended for raking grass hay and straw crops on the

ground.

The rotary rake is solely constructed for usual work in agriculture.

The rotary rake should only be connected to a tractor and driven by the PTO

of the tractor.

Any other use is regarded as not intended. The manufacturer is not

responsible for any damage resulting from such use, the user bears that risk.

Intended use also implies that the instructions and rules prescribed by the

manufacturer are observed.

The rotary rake should only be used, maintained and repaired by persons

who, through relevant instructions and after reading the instruction manual,

are familiar with the machine and, in particular, are informed of possible

dangers.

The following safety instructions as well as common rules concerning

technical safety, working practices and road safety must be observed

altogether.

If changes are made on the machine and its construction without permission

from the manufacturer, the manufacturer cannot be held responsible for any

damage resulting from this.

Intended use also implies that the rules prescribed by the manufacturer

concerning operation, maintenance and service are observed.

PIGB-184X-02 R+420 R+460 0218

1.2 Foreseeable misuse

Sweeping of e.g. farmyards with the rake tines or brooms fastened to these is

not allowed. There is a risk that e.g. stones are thrown out from the working

area of the machine with danger of personal injury or damage to objects.

Any use beyond the intended use is regarded as foreseeable misuse.

1.3 General safety instructions

The following is a brief description of the measures, which should be a matter of

common knowledge to the operator.

1. Always disengage the PTO drive shaft, activate the parking brake and stop the

tractor engine before you

- lubricate the machine,

- clean the machine,

- maintain the machine.

- adjust the machine.

2. Always use the transport lock when transporting the machine.

3. Never work under a raised rotor unless it is secured by means of stop blocks

or other mechanical securing device.

4. Always block the tractor wheels before working on the machine.

5. Never start the tractor until all persons are safely away from the machine.

6. Make sure that all tools have been removed from the machine before starting

the tractor.

7. Make sure that all guards are intact and have been mounted correctly.

8. The clothes of the operator must be tight-fitting. During work never wear loose

clothes or have your hair hang down as it may be pulled in by the moving parts

of the machine.

9. Always drive with the statutory lights and safety marking during transport on

public road and at night.

10.Do not stand near the machine while it is working.

11.When mounting the PTO drive shaft check that the number and direction of

RPM of the tractor matches those of the machine.

12.Before raising or lowering the machine, check that no persons are near the

machine or touching it.

13.Do not stand near the safety frames of the rake until all revolving parts have

stopped moving.

14.Never use the machine for other purposes than what it has been constructed

for.

15.Do not allow any children to be near when you are working with the machine.

16.Never stand between the tractor and the machine during connection and

disconnection.

PIGB-184X-02 R+420 R+460 0218

1.4 Technical data

1.4.1 Manufacturer’s address

Kongskilde Industries A/S

DK-6400 Sønderborg –Denmark

1.4.2 Certificates

-EC-Declaration of conformity (see page 46)

1.4.3 Marking of the machine

The machine data are printed on the.

machine plate. The machine plate is

placed in the right-hand side in the

direction of travelling behind the

suspension.

The marking on the machine should neither be changed nor removed!

The information on the machine plate can be written below so that it is always at

hand.

Machine type

Serial number

Manufacturing year

PIGB-184X-02 R+420 R+460 0218

In case of service questions and when ordering spare parts, please state machine

type, serial number and manufacturing year so that the inquiry can be treated as

soon as possible.

Only use original KONGSKILDE spare parts. The manufacturer

cannot be held responsible for any damage resulting from the use of

non-original spare parts.

1.5.4 General technical data

Technical data:

R+420

R+460

Rotor diameter:

3.20 m

3.50 m

Tine arms per rotor:

Double tines per tine arm:

Working width, max:

4.15 m

4.45 m

Minimum transport width:

1.90 m

2.18 m

Length (with tine arms / without PTO shaft):

3.70 m

4.00 m

Number of revolution, PTO:

540 RPM

Link arm category:

I + II

Suspension type:

3-point

Power requirement:

from 30/40 kW/HP

from 33/45 kW/HP

Number of rotor wheels:

Wheels, rotor:

18.5x8.50-8 (6PR)

Tyre pressure

2.2 bar

Electricity (for extra lighting kit)

12 V

Equivalent sound pressure level

under 70 dB(A)

Weight, approx.:

570 kg

650 kg

R+420

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kongskilde Landwirtschaftliche Geräte Handbücher

Kongskilde

Kongskilde FRONT TERRA-C Bedienungsanleitung

Kongskilde

Kongskilde CFA 20 Bedienungsanleitung

Kongskilde

Kongskilde TERRA-D Handbuch

Kongskilde

Kongskilde K 20 C Handbuch

Kongskilde

Kongskilde 8200 Series Bedienungsanleitung

Kongskilde

Kongskilde 300 DDSS Bedienungsanleitung

Kongskilde

Kongskilde R400 Bedienungsanleitung

Kongskilde

Kongskilde Z 685 Pro Bedienungsanleitung

Kongskilde

Kongskilde VIBRO TILL 2800 Bedienungsanleitung

Kongskilde

Kongskilde GMT L Series Bedienungsanleitung

Kongskilde

Kongskilde KCT Bedienungsanleitung

Kongskilde

Kongskilde FCT 1360 Bedienungsanleitung

Kongskilde

Kongskilde GXS 9005 Bedienungsanleitung

Kongskilde

Kongskilde FCT 1260 Bedienungsanleitung

Kongskilde

Kongskilde 2800 SERIES Bedienungsanleitung

Kongskilde

Kongskilde R 420 DS Bedienungsanleitung

Kongskilde

Kongskilde GMT FLEX Series Bedienungsanleitung

Kongskilde

Kongskilde DPC 40 Handbuch

Kongskilde

Kongskilde R 285 DS Bedienungsanleitung

Kongskilde

Kongskilde 2800 SERIES Bedienungsanleitung

Kongskilde

Kongskilde R+ 1610 S Bedienungsanleitung

Kongskilde

Kongskilde Vibro Crop Series Bedienungsanleitung

Kongskilde

Kongskilde R 655 DS Bedienungsanleitung

Kongskilde

Kongskilde FC 860 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung