Konica Minolta Di1610 Bedienungsanleitung

SERVICE MANUAL

2003.11

Ver. 1.0

2003.11 Ver.1.0

Di1610

GENERAL

Di1610

Printed in Japan

4980-7990-11

03110500

Use of this manual should be strictly supervised to

avoid disclosure of confidential information.

GENERAL

P-1

1. SAFETY PRECAUTIONS FOR INSPECTION AND

SERVICE

• When performing inspection and service procedures, observe the following precautions

to prevent accidents and ensure utmost safety.

✽Depending on the model, some of the precautions given in the following do not apply.

• Different markings are used to denote specific meanings as detailed below.

• The following graphic symbols are used to give instructions that need to be observed.

Used to call the service technician attention to what is graphically represented

inside the marking (including a warning).

Used to prohibit the service technician from doing what is graphically represented

inside the marking.

Used to instruct the service technician to do what is graphically represented

inside the marking.

1-1. Warning

WARNING

• Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION

• Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury. It may also be used to alert against unsafe practices.

WARNING

1. Always observe precautions.

• Parts requiring special attention in this product will include a label containing

the mark shown on the left plus precautionary notes. Be sure to observe the

precautions.

• Be sure to observe the “Safety Information” given in the Operator’s Manual.

P-2

WARNING

2. Before starting the procedures, be sure to unplug the power cord.

• This product contains a high-voltage unit and a circuit with a large current

capacity that may cause an electric shock or burn.

• The product also contains parts that can jerk suddenly and cause injury.

• If this product uses a laser, laser beam leakage may cause eye damage or

blindness.

3. Do not throw toner or the toner bottle into a fire.

• Do not throw toner or the Toner Bottle (Imaging Cartridge, Toner Cartridge) into

a fire. Toner expelled from the fire may cause burns.

4. Use the specified parts.

• For replacement parts, always use the genuine parts specified in the manufac-

turer’s parts manual. Installing a wrong or unauthorized part could cause

dielectric breakdown, overload, or undermine safety devices resulting in possi-

ble electric shock or fire.

• Replace a blown electrical fuse or thermal fuse with its corresponding genuine

part specified in the manufacturer’s parts manual. Installing a fuse of a different

make or rating could lead to a possible fire. If a thermal fuse blows frequently,

the temperature control system may have a problem and action must be taken

to eliminate the cause of the problem.

5. Handle the power cord with care and never use a multiple outlet.

• Do not break, crush or otherwise damage the power cord. Placing a heavy

object on the power cord, or pulling or bending it may damage it, resulting in a

possible fire or electric shock.

• Do not use a multiple outlet to which any other appliance or machine is con-

nected.

• Be sure the power outlet meets or exceeds the specified capacity.

• Use only the power cord supplied in the package. If a power cord is not sup-

plied, only use the power cord and plug that is specified in POWER CORD

INSTRUCTION. Failure to use this cord could result in a fire or electrical shock.

• Use the power cord supplied in the package only for this machine and NEVER

use it for any other product. Failure to observe this precaution could result in a

fire or electrical shock.

6. Be careful with the high-voltage parts.

• A part marked with the symbol shown on the left carries a high voltage. Touch-

ing it could result in an electric shock or burn. Be sure to unplug the power cord

before servicing this part or the parts near it.

7. Do not work with wet hands.

• Do not unplug or plug in the power cord, or perform any kind of service or

inspection with wet hands. Doing so could result in an electric shock.

P-3

1-2. Caution

WARNING

8. Do not touch a high-temperature part.

• A part marked with the symbol shown on the left and other parts such as the

exposure lamp and fusing roller can be very hot while the machine is ener-

gized. Touching them may result in a burn.

• Wait until these parts have cooled down before replacing them or any sur-

rounding parts.

9. Maintain a grounded connection at all times.

• Connect the power cord to an electrical outlet that is equipped with a grounding

terminal.

10. Do not remodel the product.

• Modifying this product in a manner not authorized by the manufacturer may

result in a fire or electric shock. If this product uses a laser, laser beam leakage

may cause eye damage or blindness.

11. Restore all parts and harnesses to their original positions.

• To promote safety and prevent product damage, make sure the harnesses are

returned to their original positions and properly secured in their clamps and

saddles in order to avoid hot parts, high-voltage parts, sharp edges, or being

crushed.

• To promote safety, make sure that all tubing and other insulating materials are

returned to their original positions. Make sure that floating components

mounted on the circuit boards are at their correct distance and position off the

boards.

CAUTION

1. Precautions for Service Jobs.

• A star washer and spring washer, if used originally, must be reinstalled. Omit-

ting them may result in contact failure which could cause an electric shock or

fire.

• When reassembling parts, make sure that the correct screws (size, type) are

used in the correct places. Using the wrong screw could lead to stripped

threads, poorly secured parts, poor insulating or grounding, and result in a mal-

function, electric shock or injury.

• Take great care to avoid personal injury from possible burrs and sharp edges

on the parts, frames and chassis of the product.

• When moving the product or removing an option, use care not to injure your

back or allow your hands to be caught in mechanisms.

P-4

CAUTION

2. Precautions for Servicing with Covers and Parts Removed.

• Wherever feasible, keep all parts and covers mounted when energizing the

product.

• If energizing the product with a cover removed is absolutely unavoidable, do

not touch any exposed live parts and use care not to allow your clothing to be

caught in the moving parts. Never leave a product in this condition unattended.

• Never place disassembled parts or a container of liquid on the product. Parts

falling into, or the liquid spilling inside, the mechanism could result in an elec-

tric shock or fire.

• Never use a flammable spray near the product. This could result in a fire.

• Make sure the power cord is unplugged before removing or installing circuit

boards or plugging in or unplugging connectors.

• Always use the interlock switch actuating jig to actuate an interlock switch

when a cover is opened or removed. The use of folded paper or some other

object may damage the interlock switch mechanism, possibly resulting in an

electric shock, injury or blindness.

3. Precautions for the Working Environment.

• The product must be placed on a flat, level surface that is stable and secure.

• Never place this product or its parts on an unsteady or tilting workbench when

servicing.

• Provide good ventilation at regular intervals if a service job must be done in a

confined space for a long period of time.

• Avoid dusty locations and places exposed to oil or steam.

• Avoid working positions that may block the ventilation ports of the product.

4. Precautions for Handling Batteries. (Lithium, Nickel-Cadmium, etc.)

• Replace a rundown battery with the same type as specified in the manufac-

turer’s parts manual.

• Before installing a new battery, make sure of the correct polarity of the installa-

tion or the battery could burst.

• Dispose of used batteries according to the local regulations. Never dispose of

them at the user’s premises or attempt to try to discharge one.

5. Precautions for the Laser Beam. (Only for Products Employing a Laser)

• Removing the cover marked with the caution label could lead to possible expo-

sure to the laser beam, resulting in eye damage or blindness. Be sure to

unplug the power cord before removing this cover.

• If removing this cover while the power is ON is unavoidable, be sure to wear

protective laser goggles that meet specifications.

• Make sure that no one enters the room when the machine is in this condition.

• When handling the laser unit, observe the “Precautions for Handling Laser

Equipment.”

6. Precautions for storing the toner or imaging cartridge.

• Be sure to keep the toner or imaging cartridge out of the reach of children.

Licking the imaging cartridge or ingesting its contents is harmful to your health.

P-5

1-3. Used Batteries Precautions

ALL Areas

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

Germany

VORSICHT!

Explosionsgefahr bei unsachgemäßem Austausch der Batterie.

Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleichwertigen Typ.

Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

France

ATTENTION

Il y a danger d’explosion s’il y a remplacement incorrect de la batterie.

Remplacer uniquement avec une batterie du même type ou d’un type équivalent recom-

mandé par le constructeur.

Mettre au rebut les batteries usagées conformément aux instructions du fabricant.

Denmark

ADVARSEL!

Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandøren.

Finland, Sweden

VAROlTUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.

Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

VARNING

Explosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparat-

tillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

Norway

ADVARSEL

Eksplosjonsfare ved feilaktig skifte av batteri.

Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten.

Brukte batterier kasseres i henhold til fabrikantens instruksjoner.

P-6

1-4. Other Precautions

• When handling circuit boards, observe the “HANDLING of PWBs”.

• The PC Drum is a very delicate component. Observe the precautions given in “HAN-

DLING OF THE PC DRUM” because mishandling may result in serious image problems.

• Note that replacement of a circuit board may call for readjustments or resetting of partic-

ular items, or software installation.

1-5. Precautions for Service

• When performing inspection and service procedures, observe the following precautions

to prevent mishandling of the machine and its parts.

✽Depending on the model, some of the precautions given in the following do not apply.

1. Precautions Before Service

• When the user is using a word processor or personal computer from a wall outlet of the

same line, take necessary steps to prevent the circuit breaker from opening due to over-

loads.

• Never disturb the LAN by breaking or making a network connection, altering termination,

installing or removing networking hardware or software, or shutting down networked

devices without the knowledge and express permission of the network administrator or

the shop supervisor.

2. How to Use this Book

DIS/REASSEMBLY, ADJUSTMENT

• To reassemble the product, reverse the order of disassembly unless otherwise specified.

TROUBLESHOOTING

• If a component on a PWB or any other functional unit including a motor is defective, the

text only instructs you to replace the whole PWB or functional unit and does not give trou-

bleshooting procedures applicable within the defective unit.

• All troubleshooting procedures contained herein assume that there are no breaks in the

harnesses and cords and all connectors are plugged into the right positions.

• The procedures preclude possible malfunctions due to noise and other external causes.

3. Precautions for Service

• Keep all disassembled parts in good order and keep tools under control so that none will

be lost or damaged.

• After completing a service job, perform a safety check. Make sure that all parts, wiring

and screws are returned to their original positions.

• Do not pull out the toner hopper while the toner bottle is turning. This could result in a

damaged motor or locking mechanism.

• If the product is to be run with the front door open, make sure that the toner hopper is in

the locked position.

• Do not use an air gun or vacuum cleaner for cleaning the ATDC Sensor and other sen-

sors, as they can cause electrostatic destruction. Use a blower brush and cloth. If a unit

containing these sensors is to be cleaned, first remove the sensors from the unit.

P-7

4. Precautions for Dis/Reassembly

• Be sure to unplug the copier from the outlet before attempting to service the copier.

• The basic rule is not to operate the copier anytime during disassembly. If it is absolutely

necessary to run the copier with its covers removed, use care not to allow your clothing

to be caught in revolving parts such as the timing belt and gears.

• Before attempting to replace parts and unplug connectors, make sure that the power

cord of the copier has been unplugged from the wall outlet.

• Be sure to use the Interlock Switch Actuating Jig whenever it is necessary to actuate the

Interlock Switch with the covers left open or removed.

• While the product is energized, do not unplug or plug connectors into the circuit boards

or harnesses.

• Never use flammable sprays near the copier.

• A used battery should be disposed of according to the local regulations and never be dis-

carded casually or left unattended at the user’s premises.

• When reassembling parts, make sure that the correct screws (size, type) and toothed

washer are used in the correct places.

5. Precautions for Circuit Inspection

• Never create a closed circuit across connector pins except those specified in the text and

on the printed circuit.

• When creating a closed circuit and measuring a voltage across connector pins specified

in the text, be sure to use the GND wire.

6. Handling of PWBs

During Transportation/Storage

• During transportation or when in storage, new P.W. Boards must not be indiscriminately

removed from their protective conductive bags.

• Do not store or place P.W. Boards in a location exposed to direct sunlight and high tem-

perature.

• When it becomes absolutely necessary to remove a Board from its conductive bag or

case, always place it on its conductive mat in an area as free as possible from static elec-

tricity.

• Do not touch the pins of the ICs with your bare hands.

• Protect the PWBs from any external force so that they are not bent or damaged.

During Inspection/Replacement

• Avoid checking the IC directly with a multimeter; use connectors on the Board.

• Never create a closed circuit across IC pins with a metal tool.

• Before unplugging connectors from the P.W. Boards, make sure that the power cord has

been unplugged from the outlet.

• When removing a Board from its conductive bag or conductive case, do not touch the

pins of the ICs or the printed pattern. Place it in position by holding only the edges of the

Board.

• When touching the PWB, wear a wrist strap and connect its cord to a securely grounded

place whenever possible. If you cannot wear a wrist strap, touch a metal part to dis-

charge static electricity before touching the PWB.

• Note that replacement of a PWB may call for readjustments or resetting of particular

items.

7. Handling of Other Parts

• The magnet roller generates a strong magnetic field. Do not bring it near a watch, floppy

disk, magnetic card, or CRT tube.

P-8

8. Handling of the PC Drum

✽Only for Products Not Employing an Imaging Cartridge.

During Transportation/Storage

• Use the specified carton whenever moving or storing the PC Drum.

• The storage temperature is in the range between –20°C and +40°C.

• In summer, avoid leaving the PC Drum in a car for a long time.

Handling

• Ensure that the correct PC Drum is used.

• Whenever the PC Drum has been removed from the copier, store it in its carton or protect

it with a Drum Cloth.

• The PC Drum exhibits greatest light fatigue after being exposed to strong light over an

extended period of time. Never, therefore, expose it to direct sunlight.

• Use care not to contaminate the surface of the PC Drum with oil-base solvent, finger-

prints, and other foreign matter.

• Do not scratch the surface of the PC Drum.

• Do not apply chemicals to the surface of the PC Drum.

• Do not attempt to wipe clean the surface of the PC Drum.

If, however, the surface is contaminated with fingerprints, clean it using the following proce-

dure.

A. Place the PC Drum into one half of its carton.

1076D001

B. Gently wipe the residual toner off the surface of the

PC Drum with a dry, Dust-Free Cotton Pad.

• Turn the PC Drum so that the area of its surface on

which the line of toner left by the Cleaning Blade is

present is facing straight up. Wipe the surface in one

continuous movement from the rear edge of the PC

Drum to the front edge and off the surface of the PC

Drum.

• Turn the PC Drum slightly and wipe the newly

exposed surface area with a CLEAN face of the

Dust-Free Cotton Pad. Repeat this procedure until

the entire surface of the PC Drum has been thor-

oughly cleaned.

✽At this time, always use a CLEAN face of the dry

Dust-Free Cotton Pad until no toner is evident on the

face of the Pad after wiping.

1076D002

P-9

NOTES

• Even when the PC Drum is only locally dirtied, wipe the entire surface.

• Do not expose the PC Drum to direct sunlight. Clean it as quickly as possible even under

interior illumination.

• If dirt remains after cleaning, repeat the entire procedure from the beginning one more

time.

9. Handling of the Imaging Cartridge and Print Unit

✽Only for Products Employing an Imaging Cartridge and Print Unit.

During Transportation/Storage

• The storage temperature is in the range between –20 °C and +40 °C.

• In summer, avoid leaving the Imaging Cartridge and Print Unit in a car for a long time.

Handling

• Store the Imaging Cartridge and Print Unit in a place that is not exposed to direct sun-

light.

Precautionary Information on the PC Drum Inside the Imaging Cartridge and Print Unit.

• Use care not to contaminate the surface of the PC Drum with oil-base solvent, finger-

prints, and other foreign matter.

• Do not scratch the surface of the PC Drum.

• Do not attempt to wipe clean the surface of the PC Drum.

C. Soak a small amount of either ethyl alcohol or iso-

propyl alcohol into a clean, unused Dust-Free Cot-

ton Pad which has been folded over into quarters.

Now, wipe the surface of the PC Drum in one con-

tinuous movement from its rear edge to its front

edge and off its surface one to two times.

✽Never move the Pad back and forth.

1076D003

D. Using the SAME face of the Pad, repeat the proce-

dure explained in the latter half of step 3 until the

entire surface of the PC Drum has been wiped.

Always OVERLAP the areas when wiping. Two

complete turns of the PC Drum would be appropri-

ate for cleaning.

1076D004

Andere Handbücher für Di1610

Inhaltsverzeichnis

Andere Konica Minolta Drucker Handbücher

Konica Minolta

Konica Minolta magicolor 2200 DeskLaser Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C3100i Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1250W. Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1400W Technisches Handbuch

Konica Minolta

Konica Minolta IP-421 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub PRESS C8000 Bedienungsanleitung

Konica Minolta

Konica Minolta Di1610 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB PRO 920 Bedienungsanleitung

Konica Minolta

Konica Minolta DRYPRO Model 793 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 1690MF Bedienungsanleitung

Konica Minolta

Konica Minolta AccurioPress C2070 Bedienungsanleitung

Konica Minolta

Konica Minolta magicolor 1650EN Originalbetriebsanleitung

Konica Minolta

Konica Minolta accuriopress c6100 Bedienungsanleitung

Konica Minolta

Konica Minolta AccurioPress 6136 Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 500 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 5650EN Bedienungsanleitung

Konica Minolta

Konica Minolta 8050 Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 9100 Bedienungsanleitung

Konica Minolta

Konica Minolta Magicolor 2450 Bedienungsanleitung

Konica Minolta

Konica Minolta PagePro 1300W Konfigurationshandbuch

Konica Minolta

Konica Minolta Magicolor 4750DN Bedienungsanleitung

Konica Minolta

Konica Minolta 2060 Kurzanleitung

Konica Minolta

Konica Minolta AccurioPrint 2100 Bedienungsanleitung

Konica Minolta

Konica Minolta AccurioPress C2070 Installations- und Betriebshandbuch

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung