Kospel EPS - 3,5 Bedienungsanleitung
ELECTRIC INSTANTANEOUS
WATER HEATER
EPS - 3,5
EPS - 4,4
EPS - 5,5R
2
Please, read and follow the installation and operating instructions carefully, to ensure the long life
and reliable operation of this appliance.
The manufacturer may make minor changes in the appliance if necessary. They will not be exposed
in the operating instruction, so long as the main features of the heater remain the same.
EPS electric instantaneous water heater is designed to heat domestic water in households, sanitary
rooms, labs, plants etc., in other words, everywhere where there is a demand for instant hot water.
Turning the hot water tap on, automatically starts up the heater (a red light on the heater’s outer case
comes on). Water is heated instantly as a result. The temperature of heated water depends on the rate
of flow: the greater the flow, the lower the temperature. Turning the hot water off, shuts the appliance.
Purpose
Working and safety
conditions
- theapplianceshouldbeinstalledandthereliabilityofelectricshockprotectionshouldbetested
byaprofessionalperson,
- theappliancehastobeearthedorneutrallygrounded,
- theappliancehastobepermanentlyconnectedtotheelectricalsystem,
- the appliance can be used only after proper installation (and make sure that it is in a faultless
technical condition!)
- the appliance should be vented (see “Venting”) before the first use and each time after emptying
the heater out of water (e.g. during conservation of a water supply system),
- be alert not to let the working appliance be emptied of water, which may happen with the shortage
of water in a water supply system,
- do not open the front case of the water heater while it is in on,
- do not either install any additional appliance to the tap pipe or plug it while water is flowing,
- remember that water at 40°C temp. may bring forth the feeling of burning (especially in case of
children).
This product must not be treated as a communal waste. Dismantled
appliance ought to be given to an appropriate recycling point for
electrical and electronic waste. Appropriate disposal of the used
product prevents potential negative influence on the environment,
which could occur in case of an improper waste disposal.
In order to obtain more detailed information on the recycling of
the product, contact your local authority, refuse disposal services
or the store, where the product has been purchased.
ATTENTION!
If the inseparable supply cord will become damage, it should be replaced at the manufacturer
or in special repair shop or by a qualified person in order to avoid all risks.
ENG-001B/p.410 3
Fig.1 View
[1] – workindicator
[2] – powerchangingknob(EPS-5,5R)
[4] – gaskets
[5] – filter
[6] – watersupply
[7] – rosette
[8] – tapbody
[9] – spray-head
[10] – nuts
[11] – tappipe
Installation
1 2
Fig.2 Electricconnection
F – dipolarcircuitbreaker
L – livewire
N – neutralwire
PE – earthwire
BN - brown
BU - blue
GNYE - green-yellow
Installation
1. Fix the tap set [6] on a water supply pipe [8].
2. Connect the heater to the tap body [8] with nuts [10] accompanied by gasket [4] and the filter [5].
3. Allow water mains pressure gets to the tap.
4. Check for leaks by opening the tap. Do it without the spray-head [9] on, as some impurities, which
come from the installation, may appear.
5. Vent the water installation.
6. Put the spray-head on.
7. Connect the heater to a power source (through the installation cable box according to Fig.2).
Recommendation
- connect the appliance to cold water supplies only.
ATTENTION!
Electric installation should be equipped with safety (power-differential) circuit breaker and
other devices which will ensure disconnecting the heater from the source of power (intervals
between all their poles should not be less than 3mm).
4
Venting
1. Shutoffelectricsupplies.
2. Turn the flow on (turn the hot water tap on) in order to vent the installation until the flow of water
becomes constant and even.
3. Shut off the flow.
4. Switch on the electric supplies.
ATTENTION!
Vent the appliance every time after a decay of water.
Operation
The heater is produced in 2 versions: with and without power changing knob (Fig.4 and Fig.3 re-
spectively) which is placed on the front cover.
There are 2 possible positions that the knob can be situated. In “(“ position the appliance uses lower
power than in a position “)) ” – in that case the maximum power is used. The knob is easily turned in
both directions.
ATTENTION!
In case of water shortage the tap should be shut immediately. The appliance should be vented
as soon as a water supply is back (see ‘Venting’).
3
Fig.3 OperatingindicatorEPS-3,5;EPS-4,4
[1] – ‘heaton’indicator(lamp)
4
Fig.4 OperatingindicatorEPS-5,5
[1] – 'heaton’indicator(lamp)
[2] – powerchangingknob
ENG-001B/p.410 5
Technical data
EPSwaterheater 3,5 4,4 5,5R
Rated power kW 3,5 4,4 5,5/4,4
Rated voltage 230V~
Rated current A 15,2 19,1 23,9/19,1
Min. supply water pressure MPa 0,12
Operating point l/min 1,1 1,7 2,0
Efficiency (at ∆t = 30°C) l/min 1,7 2,1 2,6/2,1
Overall dimension (length without a tap x width x depth) mm 211 x 140 x 70
Weight (with a tap) kg ~1,4
Conductor to connect with electrical installation (1.2m long) with assembly terminals
Min. water resistivity at 15°C Ωcm 1100
Fuse rated current A 16 20 25
Min. connecting wires section mm23 x 1,5 3 x 2,5
The maximum allowed network impedance Ω0,34 0,31
Water supply pipe section G1/2"
Safety class IP 25
Maintenance
5
To ensure a long and faultless work of the appliance you should carry out a seasonal cleaning of the
filter [5] in your individual capacity (this duty does not belong to a guarantee service).
To clean the heater do the following (Fig.5).
1. Cutoffwaterandelectricsupply.
2. Disconnect the heater from the tap set (see ‘Installation’).
3. Take the filter out [5] from the fittings at cold water inlet [12].
4. Clean the filter.
5. Install the filter into the former position.
6. Fix the heater on the tap set.
7. Turn on the cold water tap on – check connections for
leaks.
8. Vent the installation (see ‘Venting’).
ATTENTION!
The filter should be cleaned after the repair of a water system, when a lot of effluent appears
or after a year of operation.
Fig.5 Filtercleaning
[5] – filter
[8] – tapset
[12] – inlet–coldwater
6
Set contents
EPS water heater 1 piece
Tap set 1 piece
Gasket 2 pieces
Faults
In case the appliance does not heat water, check for possible reasons:
- a failure of the mains supplies (e.g. fuses),
- insufficient flow through the heater (e.g. dirty filter, incorrect setting of the flow regulating valve).
The guarantee does not cover the above repairs.
If there is a fault in the appliance (the heater does not work and all the above reasons do not occur),
contact the nearest authorised service.
ATTENTION!
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Inhaltsverzeichnis
Andere Kospel Boiler Handbücher
Kospel
Kospel EPO2 Bedienungsanleitung
Kospel
Kospel KDE Bedienungsanleitung
Kospel
Kospel EPJ.P Series Bedienungsanleitung
Kospel
Kospel SP180 Bedienungsanleitung
Kospel
Kospel EPS2 Bedienungsanleitung
Kospel
Kospel SWVPC-200/100 Gebrauchsanweisung
Kospel
Kospel EKP.LN2M Bedienungsanleitung
Kospel
Kospel SWK140 Gebrauchsanweisung
Kospel
Kospel KDE Bedienungsanleitung
Kospel
Kospel KDH Bedienungsanleitung
Kospel
Kospel MAXIMUS EPP-36 Bedienungsanleitung
Kospel
Kospel PPE2 Bedienungsanleitung
Kospel
Kospel EPS2-3,5 Bedienungsanleitung
Kospel
Kospel SP180 Gebrauchsanweisung
Kospel
Kospel SP180 Bedienungsanleitung
Kospel
Kospel LUXUS KDH-9 Bedienungsanleitung
Kospel
Kospel EPJ.P-4,4 Bedienungsanleitung
Kospel
Kospel EPO.D-5 Bedienungsanleitung
Kospel
Kospel MAXIMUS electronic Series Bedienungsanleitung
Kospel
Kospel EPO Amicus 4 Bedienungsanleitung
Beliebte Boiler Handbücher anderer Marken
Kenmore
Kenmore 153.582400 Bedienungsanleitung
Applimo
Applimo Edel AIR Bedienungsanleitung
STIEBEL ELTRON
STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung
clage
clage E-Mini Series Bedienungsanleitung
Toyotomi
Toyotomi Oil Miser OM-180 Bedienungsanleitung
Bradford White
Bradford White EF Series Bedienungsanleitung
