Kramer RTBUS-24 Bedienungsanleitung

P/N: 2900-300898 Rev 4 www.KramerAV.com

USER MANUAL

MODEL:

RTBUS-24

Round Table Connection Bus

 
RTBUS-24 –Contents 
i 
 
Contents 
Introduction 1 
Getting Started 1 
Overview 2 
Typical Applications 2 
Defining the RTBUS-24 Round Table Connection Bus 3 
Installing the RTBUS-24 5 
Drilling a Hole in the Table 5 
Mounting the RTBUS-24 in a Table 5 
Connecting the Cables and Wires 6 
Using the RTBUS-24 7 
Technical Specifications 8 

Kramer Electronics Ltd.

RTBUS-24 –Introduction

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of

unique, creative, and affordable solutions to the vast range of problems that confront the video,

audio, presentation, and broadcasting professional on a daily basis. In recent years, we have

redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging materials for

possible future shipment.

•Review the contents of this user manual.

Go to www.kramerav.com/downloads/RTBUS-24 to check for up-to-date user manuals,

application programs, and to check if firmware upgrades are available (where appropriate).

Achieving the Best Performance

•Use only good quality connection cables (we recommend Kramer high-performance,

high-resolution cables) to avoid interference, deterioration in signal quality due to poor

matching, and elevated noise levels (often associated with low quality cables).

•Do not secure the cables in tight bundles or roll the slack into tight coils.

•Avoid interference from neighbouring electrical appliances that may adversely influence

signal quality.

•Position your Kramer RTBUS-24 away from moisture, excessive sunlight and dust.

This equipment is to be used only inside a building. It may only be connected to other

equipment that is installed inside a building.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by

qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

Kramer Electronics Ltd.

RTBUS-24 –Introduction

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce

the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected

and recycled. To comply with the WEEE Directive, Kramer Electronics has made

arrangements with the European Advanced Recycling Network (EARN) and will cover any

costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular

country go to our recycling pages at www.kramerav.com/support/recycling.

Overview

Congratulations on purchasing your Kramer RTBUS-24 Round Table Connection Bus. The

RTBUS-24 is an elegant furniture-mounted, round connection bus. The RTBUS-24 features a

pneumatic mechanism for pneumatic lifting and smooth closing of its lid. It is easily installed

into a table or podium top, and its interface enables you to connect any equipment to systems

installed in a room via the following connectors:

•Two 125V US power sockets (5A when connecting a single power socket and a total of 6A

when connecting both sockets).

•Two 2A USB ports for charging devices.

•One HDMI connector (supporting HDMI with Deep Color, x.v.Color™, Lip Sync, HDMI

Uncompressed Audio Channels, Dolby TrueHD, DTS-HD, and CEC.

•One C14 power socket and one HDMI connector on the underside of the unit.

RTBUS-24 comes with a black or silver sandblast textured lid.

Typical Applications

The RTBUS-24 is ideal for:

•Boardrooms.

•Conference rooms.

•Training rooms.

•Hotel lobbies.

•Cafes and restaurants.

Kramer Electronics Ltd.

RTBUS-24 –Defining the RTBUS-24 Round Table Connection Bus

Defining the RTBUS-24 Round

Table Connection Bus

This section defines the RTBUS-24.

Figure 1: RTBUS-24 Round Table Connection Bus

Feature

Function

Pop-up Lid

Covers the connecting surface, leaving the table surface neat and

tidy.

Outer Rim

Fits over a table surface.

Pneumatic Mechanism

Enables automatic lifting and smooth closing of the lid.

Connecting Surface

See Figure 2.

Rubber Protectors (x2)

Protect the table surface when mounting the unit.

Locking Butterfly Nuts (x2)

Tighten to lock the mounting butterfly screw.

Mounting Screws (x2)

For securing the RTBUS-24 to the table.

Mounting Butterfly Nuts (x2)

Tighten to secure the unit to the table surface.

Kramer Electronics Ltd.

RTBUS-24 –Defining the RTBUS-24 Round Table Connection Bus

Feature

Function

Mounting Brackets (x2)

Place in the bracket slits after inserting the enclosure into the table,

for securing the unit to the table surface

Mounting Bracket Slits (two slits

on each side)

Insert the mounting brackets to the slits when installing the

RTBUS-24 (see Mounting the RTBUS-24 in a Table on page 5).

HDMI Cable

Connect to an HDMI acceptor.

Figure 2 defines the connecting surface.

Figure 2: RTBUS-24 Connecting Surface

Feature

Function

5A/125V Power Connector (x2)

Connect to up to two US power consuming devices

simultaneously.

When a single power socket is connected, consumption

should not exceed 5A.

When both power sockets are connected, the total

consumption should not exceed 6A.

5V-2A USB CHARGING Port (x2)

Use to charge up to two devices simultaneously.

Lid Latch

For safely closing the lid.

HDMI Connector

Connect to an HDMI source.

Kramer Electronics Ltd.

RTBUS-24 –Installing the RTBUS-24

Installing the RTBUS-24

RTBUS-24 Installation includes the following steps:

•Drilling a Hole in the Table on page 5.

•Mounting the RTBUS-24 in a Table on page 5.

•Connecting the Cables and Wires on page 6.

Drilling a Hole in the Table

To drill an opening in a table:

1. Using any standard cup bit drill with a diameter ranging from 111mm to 114mm (4.37”to

4.49”), drill a hole in the table in the desired location.

The thickness of the table should be 76mm (3”) or less.

2. Clean the table surface.

Take care not to damage the table. Kramer Electronics is not responsible for any damage

caused to the table.

Mounting the RTBUS-24 in a Table

To mount the unit, follow these steps:

Step 1: Insert the RTBUS-24 into the hole cut

into the table, making sure the outer rim is firm

against the surface of the table.

Kramer Electronics Ltd.

RTBUS-24 –Installing the RTBUS-24

Step 2: From underneath the table, slide the

mounting brackets into the appropriate slots.

Step 3: Tighten the butterfly mounting screws

securely upward against the table.

Step 4: Lock the mounting screws into position

with the locking butterfly screws.

Connecting the Cables and Wires

Following installation connect the cables to the underside of the unit:

•Connect the HDMI connector to an HDMI acceptor.

•Connect the power cable to a power source.

Make sure that when:

•A single power socket is connected, consumption should not exceed 5A.

•Both power sockets are connected, the total consumption should not exceed 6A.

Kramer Electronics Ltd.

RTBUS-24 –Using the RTBUS-24

Using the RTBUS-24

Once the RTBUS-24 is installed, you can easily customize it to your own needs by directly

plugging in the required AV equipment.

Figure 3: Connecting RTBUS-24

Kramer Electronics Ltd.

RTBUS-24 –Technical Specifications

Technical Specifications

Ports

1 HDMI

On an HDMI connector

2 USB Ports

5V, 2A on female USB-B connectors

for charging devices

2 US Power Sockets

For powering devices

Power

Consumption

125V AC, 50/60Hz, 6.3A

Fuse Rating

T 6.3A 250V

When a single power socket is connected, consumption

should not exceed 5A.

When both power sockets are connected, the total

consumption should not exceed 6A.

Environmental

Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory

Compliance

Safety

CE, UL

Environmental

RoHs, WEEE

Enclosure

Type

Aluminum

General

Net Dimensions (W, D, H)

15.4cm x 10.7cm x 10.7cm

(6.06" x 4.21" x 4.21")

Shipping Dimensions

(W, D, H)

36.5cm x 17 cm x 17cm

(14.37" x 6.69" x 6.69")

Net Weight

0.728kg (1.6lbs)

Shipping Weight

1.53kg (3.37lbs) approx.

Accessories

Included

Clamps set

Specifications are subject to change without notice at www.kramerav.com

Andere Handbücher für RTBUS-24

Inhaltsverzeichnis

Andere Kramer Kabel und Steckverbinder Handbücher

Kramer

Kramer TBUS-4 Bedienungsanleitung

Kramer

Kramer WP-209 Bedienungsanleitung

Kramer

Kramer CLS-AOCH/60 Series Bedienungsanleitung

Kramer

Kramer WP-220 Bedienungsanleitung

Kramer

Kramer 6010 Bedienungsanleitung

Kramer

Kramer UTBUS-1XL Bedienungsanleitung

Kramer

Kramer KRT-3 Bedienungsanleitung

Kramer

Kramer WAV-6UAB Bedienungsanleitung

Kramer

Kramer MODULAR TBUS-1A Bedienungsanleitung

Kramer

Kramer UTBUS-2XL Bedienungsanleitung

Kramer

Kramer TBUS-3 Bedienungsanleitung

Kramer

Kramer WP-210E Bedienungsanleitung

Kramer

Kramer 676T Bedienungsanleitung

Kramer

Kramer TBUS-6 Bedienungsanleitung

Kramer

Kramer FODPM Bedienungsanleitung

Kramer

Kramer 612T Bedienungsanleitung

Kramer

Kramer CRS-AOCH/CLR/60 Service-Handbuch

Kramer

Kramer KRT-4-LAN Bedienungsanleitung

Kramer

Kramer WSP-1 Bedienungsanleitung

Kramer

Kramer WP-210A Bedienungsanleitung

Kramer

Kramer VM-10H2 Bedienungsanleitung

Kramer

Kramer MODULAR TBUS-1Axl Bedienungsanleitung

Kramer

Kramer HDBT Bedienungsanleitung

Kramer

Kramer LPE Installationshandbuch

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung