Kramer RTBUS-28XL Bedienungsanleitung

P/N: 2900-301535 Rev 1 www.kramerAV.com

USER MANUAL

MODEL:

RTBUS-28XL

Round Table Connection Bus

Kramer Electronics Ltd.

RTBUS-28XL –Contents

Contents

Introduction 1

Getting Started 1

Overview 2

Defining RTBUS-28XL Round Table Connection Bus 3

The RTBUS-28XL Connecting Surface 4

Universal Power Socket 4

Installing the RTBUS-28XL 5

Drilling a Hole in the Table 5

Connecting the Cables 5

Mounting the RTBUS-28XL in the Table 7

Using the RTBUS-28XL 8

Technical Specifications 9

Kramer Electronics Ltd.

RTBUS-28XL –Introduction

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world

of unique, creative, and affordable solutions to the vast range of problems that confront the

video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we

have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging materials for

possible future shipment.

•Review the contents of this user manual.

Go to www.kramerav.com/downloads/RTBUS-28xl to check for up-to-date user manuals,

application programs, and to check if firmware upgrades are available (where appropriate).

Achieving Best Performance

•Use only good quality connection cables (we recommend Kramer high-performance,

high-resolution cables) to avoid interference, deterioration in signal quality due to poor

matching, and elevated noise levels (often associated with low quality cables).

•Do not secure the cables in tight bundles or roll the slack into tight coils.

•Avoid interference from neighboring electrical appliances that may adversely influence

signal quality.

•Position your Kramer RTBUS-28XL away from moisture, excessive sunlight and dust.

Safety Instructions

Caution:

•This equipment is to be used only inside a building. It may only be connected to other

equipment that is installed inside a building.

•There are no operator serviceable parts inside the unit.

Kramer Electronics Ltd.

RTBUS-28XL –Introduction

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce

the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected

and recycled. To comply with the WEEE Directive, Kramer Electronics has made

arrangements with the European Advanced Recycling Network (EARN) and will cover any

costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular

country go to our recycling pages at www.kramerav.com/support/recycling.

Overview

Congratulations on purchasing your Kramer RTBUS-28XL Round Table Connection Bus.

The RTBUS-28XL is an elegant furniture-mounted, round connection bus. The RTBUS-28XL

features a mechanism for pneumatic lifting and smooth closing of its lid. It is easily installed

into a table or podium top, and its interface enables you to connect any equipment to systems

installed in a room:

•Four pass-through openings for cables, located on the lower surface, enabling closing of

the lid while keeping the cables hidden and protected under the surface.

•USB type A and USB type B ports for charging.

•A Universal power socket.

Kramer Electronics Ltd.

RTBUS-28XL –Defining RTBUS-28XL Round Table Connection Bus

Defining RTBUS-28XL Round

Table Connection Bus

This section defines RTBUS-28XL.

Figure 1: RTBUS-28XL Round Table Connection Bus Front Panel

Feature

Function

Pneumatic Mechanism

Enables automatic lifting and smooth closing of the lid.

Outer Rim

Fits over the table surface.

Mounting Screws (x2)

For securing RTBUS-28XL to the table.

Locking Butterfly Nuts (x2)

Tighten to lock the mounting butterfly screw.

Mounting Butterfly Nuts (x2)

Tighten to secure the unit to the table surface.

Mounting Brackets (x2)

For securing the unit to the table surface.

Black Anodized or Brushed

Aluminum Semi-Automatic Lid

(with Opening for Cable Pass-

Through)

Covers the connecting surface, leaving the table surface neat and tidy.

Lid Latch (x2)

For safely closing the lid.

Inner Pass-Through Opening

and Bushing (x1)

Insert a cable through the opening and the bushing –for larger or

multiple cables (inner diameter approx. 12.5mm Ø).

Pass-Through Opening and

Bushing (x3)

Insert a cable through the opening and the bushing (inner diameter

approx. 10 mm Ø).

Kramer Electronics Ltd.

RTBUS-28XL –Defining RTBUS-28XL Round Table Connection Bus

The RTBUS-28XL Connecting Surface

Figure 2 defines the connecting surface.

Figure 2: RTBUS-28XL Connecting Surface

Feature

Function

USB-C Charging Port

Use to charge a device.

5V-2.4A/1A USB Charging Port

Use to charge a device.

5A MAX. Universal Power Socket

Connect to a 90-240V AC power consuming device.

Universal Power Socket

A Universal Power Socket is available for general use and is fully compatible with power plugs in

the UK, India, Italy and Denmark, as well as with the 2-prong Europlug. The Universal Power

Socket is partially compatible (if the polarity is reversed) with plugs in China, Switzerland, Israel

and the USA but does not supply grounding to plugs in Central Europe and France and is not

compatible with South African plugs.

Kramer Electronics Ltd.

RTBUS-28XL –Installing the RTBUS-28XL

Installing the RTBUS-28XL

To install the RTBUS-28XL perform the following steps:

1. Drill a hole in the table (see Drilling a Hole in the Table on page 5).

2. Connect the cables (see Connecting the Cables on page 5).

3. Secure the unit to the table (see Mounting the RTBUS-28XL in the Table on page 7).

Drilling a Hole in the Table

To drill an opening in the table:

1. Using any standard cup bit drill with a diameter ranging from 138mm to 140mm (5.4” to

5.5”), drill a hole in the table in the desired location.

The thickness of the table should be 3”w (76mm) or less.

2. Clean the table surface.

Take care not to damage the table. Kramer AV is not responsible for any damage caused to

the table.

Connecting the Cables

You can install the cables either before mounting the RTBUS-28XL on a table, or after it is

mounted (usually if the RTBUS-28XL is mounted and you need to replace the cables).

To connect the cables:

1. Insert the cables through the

pass-through openings.

Kramer Electronics Ltd.

RTBUS-28XL –Installing the RTBUS-28XL

2. Insert a cable into an opening

and place the bushing around

the cable.

3. Push the bushing into the pass-

through opening to secure.

We recommend that you use the Kramer C-AC AC Power Cord series to power the unit.

Kramer Electronics Ltd.

RTBUS-28XL –Installing the RTBUS-28XL

Mounting the RTBUS-28XL in the Table

To mount the unit:

1. Insert the RTBUS-28XL into the hole

cut into the table making sure the

outer rim is firm against the surface of

the table.

2. From underneath the table, slide the

mounting brackets into the

appropriate slots.

3. Step 3: Tighten the butterfly mounting

screws securely upward against the

table.

4. Lock the mounting screws into

position with the locking butterfly

screws.

Kramer Electronics Ltd.

RTBUS-28XL –Using the RTBUS-28XL

Using the RTBUS-28XL

Once the RTBUS-28XL is installed, you can easily customize it to your own needs by directly

plugging in the required AV equipment, as illustrated in the example in Figure 3.

Figure 3: RTBUS-28XL Boardroom Installation

Andere Handbücher für RTBUS-28XL

Inhaltsverzeichnis

Andere Kramer Kabel und Steckverbinder Handbücher

Kramer

Kramer C-FODM/FODM-33 Bedienungsanleitung

Kramer

Kramer RTBUS-28XL Bedienungsanleitung

Kramer

Kramer WP-211DS Bedienungsanleitung

Kramer

Kramer TBUS-6 Bedienungsanleitung

Kramer

Kramer 6010 Bedienungsanleitung

Kramer

Kramer UTBUS-1XL Bedienungsanleitung

Kramer

Kramer UTBUS-2XL Bedienungsanleitung

Kramer

Kramer T6F-09 Bedienungsanleitung

Kramer

Kramer K-Able Box Bedienungsanleitung

Kramer

Kramer WP-230 Bedienungsanleitung

Kramer

Kramer VM-10H2 Bedienungsanleitung

Kramer

Kramer FODPM Bedienungsanleitung

Kramer

Kramer RTBUS-27xl Bedienungsanleitung

Kramer

Kramer WP-210A Bedienungsanleitung

Kramer

Kramer TBUS-100XL Bedienungsanleitung

Kramer

Kramer 612T Bedienungsanleitung

Kramer

Kramer CLS-AOCH/60 Series Bedienungsanleitung

Kramer

Kramer MODULAR TBUS-1A Bedienungsanleitung

Kramer

Kramer WP-210 Bedienungsanleitung

Kramer

Kramer WP-220 Bedienungsanleitung

Kramer

Kramer CRS-AOCH/CLR/60 Service-Handbuch

Kramer

Kramer WP-220E Bedienungsanleitung

Kramer

Kramer TBUS-4 Bedienungsanleitung

Kramer

Kramer SV-301 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung