Kramer VS-622DT Bedienungsanleitung

-622DT Enhanced Quick Start (P/N: 2900-300856QS REV 2)

P/N:

2900- 300856QS

Rev:

Scan for full manual

VS-622DT Quick Start Guide

This guide helps you install and use your VS-622DT for the first time.

Go to www.kramerav.com/downloads/VS-622DT to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VS-622DT

6x2 HDMI / HDBT Audio Matrix Switcher 1 Quick start guide 1 Set of rack ears

1 Power cord 4 Rubber feet

Step 2: Get to know your VS-622DT

# Feature Function

IR LED

Lights red when the unit accepts IR remote commands.

IR Receiver

Receives signals from the remote control transmitter.

3 ON LED Lights when the unit is powered.

4 TO OUT 1 Press to select an input to switch to OUT 1 (from 1 to 6).

TO OUT 2

Press to select an input to switch to OUT 2 (from 1 to 6).

LOCK Button

Press to lock the front panel buttons.

7 SWAP Button Press to swap

between audio outputs.

8 PATTERN Button Press to activate the test pattern generator. When the generator is active, press one of the input

buttons to select a test pattern.

EDID Button

Press to capture the EDID.

10 Output 1 Audio Buttons VOL +: Increase output 1 volume.

VOL -: Decrease output 1 volume.

MUTE: Mute output 1 audio signal.

11 Output 2 Audio Buttons VOL +: Increase output 2 volume.

VOL -: Decrease output 2 volume.

MUTE: Mute output 1 audio signal.

12 HDBT RS-232 LEDs Indicates data transmission from a controller to a device connected to the transmitter via

HDBT OUT 1:

TX 1: Lights green when data is transmitted via HDBT OUT 1.

RX 1: Lights red when data is received on HDBT OUT 1.

13 EXTERNAL (Controller)

LEDs

Indicates data transmission via the RS-232 port (item 29) to the VS-622DT:

TX 2: Lights green when data is transmitted on the RS-232 port.

RX 2: Lights red when data is received on the RS-232 port.

IR OUTPUT LEDs (1 to 4)

Lights green when the relevant IR port transmits data.

15 GPI/O LEDs (1 to 2) Lights green when the port is triggered.

16 RELAY LEDs (1 to 2) Lights green when the relay is closed.

# Feature Function

17 HDBT IN 1 RJ-45 Connectors (1 to 2) Connect to an HDBT transmitter (for example,

TP-580Txr

18 POE STATUS and LINK LEDs (for HDBT IN 1 to 2

and HDBT OUT 1)

Light when PoE is available and a link is established.

Control RS-232 3-pin Terminal Block

Connect to the serial controller to control the device.

20 AUDIO OUT Balanced Stereo Audio 5-pin Terminal

Block Connectors (1 to 2)

Connect to an analog audio acceptor.

21 SETUP DIP-switches Used to set the device behavior.

22 INPUT HDMI Connectors (3 to 6) Connect to HDMI source (from 1 to 8).

ETHERNET RJ-45 Connector

Connect to a remote network controller via a LAN.

HDBT OUT1 RJ-45 Connector

Connect to an HDBT receiver (for example, TP-580Rxr)

25 HDMI OUT 2 Connector Connect to an HDMI acceptor.

26 RESET Switch Press and hold while powering on the device to reset to factory

default parameters.

27 Hi-Z OUT Terminal Block Connectors Lo-Z – connect stereo output to Lo-Z speakers:

L+ and L- to the left speaker; R+R- to the right speaker.

Hi-Z (70V or 100V) – connect Hi-Z and COM to mono Hi-Z

speakers.

PROG Mini USB Connector

Connect to a PC to perform firmware upgrade.

29 RS-232 (G, Rx, Tx) Terminal Block Connector Connect to an RS-232 controlled device.

30 MAESTRO CONTROL 9-pin Terminal Block

Connectors

Connect to configurable buttons (configured via the Automation

page), such as the

RC-21TB

IR OUTPUT 2-pin Terminal Block Connectors (1 to 4)

Connect to IR blasters/emitters using cables up to 80m (260ft) long.

32 GPI/O 2-pin Terminal Block Connectors (1 to 2) Connect to controllable sensors or devices (for example, motion

sensors). This port can be configured as a digital input, digital

output, or analog input.

33 RELAY 2-pin Terminal Block Connectors (1 to 2) Connect to a relay controllable device, (for example, a motorized

projection screen).

34 Mains Power Connector, Fuse, and Switch Connect to the mains supply.

Step 3: Install VS-622DT

Install VS-622DT using one of the following methods:

•Remove the three screws from each side of the unit, reinsert those screws through the

rack ears and mount on a 19" rack.

•Attach the rubber feet and place the unit on a flat surface.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-622DT. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-622DT.

RJ-45 Pinout:

Audio output pinout:

For the Ethernet connector, see the wiring diagram below: To a balanced stereo

audio acceptor:

To an unbalanced

stereo audio

acceptor:

PIN EIA /TIA 568B

PIN Wire Color

1 Orange / White

2 Orange

3 Green / White

4 Blue

5 Blue / White

6 Green

7 Brown / White

8 Brown

For optimum range and performance use the recommended Kramer

cables available at www.kramerav.com/product/VS-622DT.

DIP-switch setup

A switch that is down is on; a switch that is up is off. By default, all the switches are up (off).

# Feature Description

1 HDCP support on inputs On (down)—Disable HDCP support on all inputs.

Off (up)—Enable HDCP support which is defined by P3000

commands.

2 Video mode switching

Output 1

On (down)—Auto.

Off (up)—Manual.

3 Last connected/Priority

mode Output 1

When DIP-switch 2 is set to Auto (ON):

On (down)—Enable Last Connected mode.

Off (up)—Enable Priority mode where the priority of each input

is defined by the input number, (1 is the highest priority).

4 Video mode switching

Output 2

On (down)—Auto.

Off—Manual.

5 Last connected/Priority

mode Output 2

When DIP-switch 4 is set to Auto (ON):

On (down)—Enable Last-connected mode.

Off (up)—Enable Priority mode where the priority of each input

is defined by the input number, (1 is the highest priority).

N/A

7 Range mode for

HDBT IN 1

On (down) – HDBaseT Ultra-long range (provides increased

range at a reduced bandwidth).

Off (up) – Normal range (default).

8 Range mode for

HDBT IN 2

On (down) – HDBaseT Ultra-long range (provides increased

range at a reduced bandwidth).

Off (up) – Normal range (default).

Step 5: Connect the power

Connect the power cord to VS-622DT and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operate the VS-622DT

Web pages:

-232 and Ethernet:

RS-232/Ethernet

Baud Rate: 115,200 Parity: None

Data Bits: 8 Command Format: ASCII Protocol 3000

Stop Bits:

Example (Route input 1 to output 1):

#VID1> 1<cr>

Ethernet Parameters

IP Address:

192.168.1.39

Default UDP Port #:

50000

Subnet Mask: 255.255.0.0

Default Gateway: 192.168.0.1

Full Factory Reset

OSD: Front panel buttons: power off the device, press and hold the

RESET button for 3 seconds while powering the device, and

then release.

Protocol 3000:

“#factory” command.

Web Pages:

In the Device Settings page, General tab, click Factory reset.

Technical Specifications

Inputs

2 HDBT

On female RJ-45 connectors

4 HDMI

On female HDMI connectors

Outputs

1 HDBT

On a female RJ-45 connector

1 HDMI

On a female HDMI connector

2 Stereo Balanced Audio

On 5-pin terminal block connectors

1 Stereo or 1 Mono Speaker

On a 4-pin large terminal block

Ports 1 Ethernet

On an RJ-45 female connector

2 RS-232

On 3-pin terminal blocks

1 USB

On a mini USB connector

4 IR

On 2-pin terminal block connectors

2 GPI/O

On 2-pin terminal block connectors

2 Relays

On 2-pin terminal block connectors

Video

Max Resolution

Up to 4K@60Hz UHD (4:2:0)

Compliance

HDMI 1.4 and HDCP 1.4

Reach Extended

Up to 130m (430ft)

Controls

Front Panel

Input selection buttons, swap, EDID, lock and audio control buttons

Power, RS-232, IR, GPI/O and relay indication LEDs

Remote

RS-232

Ethernet

Web pages

IR remote control transmitter

Power

Consumption

100-240V AC, 210VA max.

Cooling

Fan Ventilation

Environmental

Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory

Compliance

Safety

Environmental

RoHs, WEEE

Enclosure

Size

19”, 1U

Type

Aluminum

General

Net Dimensions (W, D, H)

43.64cm x 23.7cm x 4.36cm (17.18" x 9.3" x 1.72")

Shipping Dimensions (W, D, H)

52.5cm x 33cm x 10.7cm (20.7" x 13" x 4.21")

Net Weight

2.6kg (5.7lbs) approx.

Shipping Weight

3.7kg (8.2lbs) approx.

Accessories

Included

Power cord

Andere Handbücher für VS-622DT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kramer Matrix-Umschalter Handbücher

Kramer

Kramer Sierra Video 3232SXL Bedienungsanleitung

Kramer

Kramer VP-4x4K Bedienungsanleitung

Kramer

Kramer VS-44H2A Bedienungsanleitung

Kramer

Kramer VS-81HD Bedienungsanleitung

Kramer

Kramer VS-3232Vxl Bedienungsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Kramer

Kramer VS-1616D Bedienungsanleitung

Kramer

Kramer VS-42H Bedienungsanleitung

Kramer

Kramer VS-211H Bedienungsanleitung

Kramer

Kramer 88V3 Bedienungsanleitung

Kramer

Kramer VS-88H Bedienungsanleitung

Kramer

Kramer VS-3232DN-EM Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1208V3S Bedienungsanleitung

Kramer

Kramer VS-6464DN-EM Bedienungsanleitung

Kramer

Kramer VS-88HDCPxl Bedienungsanleitung

Kramer

Kramer Sierra Pro XL 1608V5 Bedienungsanleitung

Kramer

Kramer VP-81SID Bedienungsanleitung

Kramer

Kramer Sierra Video 1208V3 Bedienungsanleitung

Kramer

Kramer VS-62H Bedienungsanleitung

Kramer

Kramer VS-42HN Bedienungsanleitung

Kramer

Kramer VS-48HDxl Bedienungsanleitung

Kramer

Kramer VS-1616D Bedienungsanleitung

Kramer

Kramer VS-1604 Bedienungsanleitung

Kramer

Kramer XL 3232V Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte

Lindy

Lindy 38042 Bedienungsanleitung

Extron electronics

Extron electronics MTPX Plus Series Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Shinybow USA

Shinybow USA SB-8811 Bedienungsanleitung

Optimus

Optimus Compact Bedienungsanleitung