Kramer VP-440H2 Bedienungsanleitung

VP-440H2 Enhanced Quick Start (P/N: 2900-300930QS REV 3)

P/N:

2900- 300930QS

Rev:

Scan for full manual

VP-440H2 Quick Start Guide

This guide helps you install and use your VP-440H2 for the first time.

Go to www.kramerav.com/downloads/VP-440H2 to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VP-440H2 4K Presentation Switcher Scaler

1 Power cord

1 Bracket set

1 Power supply (48V DC)

1 Quick start guide

4 Rubber feet

Step 2: Get to know your VP-440H2

Feature

Function

48 V () Slide Switch

Slide up (48V) to select a condenser type microphone; slide down to select a dynamic type

microphone (we recommend that you slide down if a microphone is not connected to the

VP-440H2).

MIC 6.3mm Jack

Connect to the microphone source.

Input Selector

Buttons

HDBT IN

Press to select the HDBT input.

HDMI IN

Press to select the HDMI input (from 1 to 3).

PC IN

Press to select the computer graphics input.

MENU Button

Displays the OSD menu.

Navigation

Buttons



Press to decrease numerical values or selectfrom several definitions.

When not in the OSD menu, press to reduce the output volume.



Press to move up the menu list values.



Press to increase numerical values or select from several definitions.

When not in the OSD menu, press to increase the output volume.



Press to move down the menu list.

ENTER

Press to accept changes and change the SETUP parameters.

RESET TO XGA/1080p Button

Press and hold for about 5 seconds to toggle the output resolution between XGA and 1080p,

alternatively.

PANEL LOCK Button

Press and hold for about 5 seconds to lock/unlock the front panel buttons.

Feature

Function

CONTROL (Tx, Rx, GND) Terminal

Block Connectors

Connect to the PC orthe serial controller to control the device.

HDBT IN (Tx, Rx, GND) Terminal Block

Connectors

Connect to a controller to control peripheral devices that are connected to the HDBT

transmitter (for example, a Blu-ray player connected to WP-20).

HDBT OUT(Tx, Rx, GND) Terminal

Block Connectors

Connect to a controller to control peripheral devices that are connected to the HDBT

receiver (for example, a projector connected to TP-580Rxr).

AUDIO INPUT

Unbalanced

Stereo 3.5 Mini

Jack

HDMI

Connect to the analog audio HDMI source (from 1 to 3).

Connect to the analog audio computer graphics source.

AUDIO OUT 3.5 Mini Jack

Connect to an unbalanced stereo audio acceptor.

ETHERNET Connector

Connects to the PC or other controller through computer networking.

VIDEO INPUT

Connectors

HDBT IN RJ-45

Connect to an HDBT transmitter (for example, WP-20).

Can supply PoE (up to 13W) to the transmitter.

HDMI IN

Connect to the HDMI source (from 1 to 3).

PC IN on15-pin HD

Connect to the computer graphics source.

HDBT OUT RJ-45 Connector

Connect to an HDBT receiver (for example, TP-580Rxr).

HDMI OUT Connector

Connect to the HDMI acceptor.

48V DC Power Terminal Block

+48VDC connector for powering the unit.

Step 3: Install VP-440H2

To mount the VP-440H2 in a rack, use an RK-1 rack adapter. Alternatively, attach the rubber feet to the underside of the

VP-440H2 and place it on a table.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VP-440H2. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to VP-440H2.

RJ-45 Pinout:

Microphone Pinout:

For the Ethernet connector, see the wiring

diagram below

The microphone 6mm jack pinout for a condenser microphone

The microphone 6mm jack pinout for a dynamic microphone.

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

For optimum range and performance use the

recommended Kramer cables available at

www.kramerav.com/product/VP-440H2.

Step 5: Connect the power

Connect the 48V DC power adapter power cord to VP-440H2 and plug it into the mains electricity.

Safety Instructions (DC)

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the Kramer Electronics power supply that is provided with the unit.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Control and operate VP-440H2 via the front panel buttons and via

Web pages:

OSD Menu:

Menu Items

Picture

Adjust contrast brightness and color, and fine-tune the image.

Input

Select input source.

Output

Select method for 4K input to 4K output handling, image size and resolution.

Audio

Select audio source, audio parameters (bass, treble and so on), microphone

settings and volume per input.

OSD

Set OSD position, transparency and so on.

Advanced

Select HDCP on each of the inputs and outputs, manage the EDID and

define IP settings.

Info.

View device information.

Factory

Reset to factory default settings.

Andere Handbücher für VP-440H2

Andere Kramer Medienkonverter Handbücher

Kramer

Kramer VP-451 Bedienungsanleitung

Kramer

Kramer VP-425 Bedienungsanleitung

Kramer

Kramer FC-4 Bedienungsanleitung

Kramer

Kramer VP-421 Bedienungsanleitung

Kramer

Kramer FC-42 Bedienungsanleitung

Kramer

Kramer 103AV Bedienungsanleitung

Kramer

Kramer VP-434 Bedienungsanleitung

Kramer

Kramer VM-1110xl Bedienungsanleitung

Kramer

Kramer VP-505 Bedienungsanleitung

Kramer

Kramer 575 Bedienungsanleitung

Kramer

Kramer KDS-EN6 Bedienungsanleitung

Kramer

Kramer VP-434 Bedienungsanleitung

Kramer

Kramer FC-15 Bedienungsanleitung

Kramer

Kramer VA-256D Bedienungsanleitung

Kramer

Kramer VM-24HDMI Bedienungsanleitung

Kramer

Kramer KDS-EN7 Bedienungsanleitung

Kramer

Kramer PT-1SPDIF Bedienungsanleitung

Kramer

Kramer WP-EN6 Bedienungsanleitung

Kramer

Kramer FC-113 Bedienungsanleitung

Kramer

Kramer FC-46H2 Bedienungsanleitung

Kramer

Kramer PT-101H4 Bedienungsanleitung

Kramer

Kramer FC-4001 Bedienungsanleitung

Kramer

Kramer VP-437N Bedienungsanleitung

Kramer

Kramer VA-1DVI Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung