KTI Networks KF-310 Bedienungsanleitung

32-bit PCI-Bus 10/100Mbps

ACPI Fast Ethernet Card

User’s Guide

FCC Statement

This device compiles with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Warning! This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

when the equipment is operated in a commercial

environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference in which case the user will be required to

correct the interference at his own expense.

CE-Mark Warning

In a domestic environment this product may cause radio

interference in which case the user may be required to take

adequate measures.

Document Version: 2.0

All Trademarks and trade names are the properties of their

respective owners.

1. Introduction

Congratulations on the purchasing of your new 10/100

NWay Fast Ethernet PCI adapter. This document describes

the Installation of network adapter. This adapter supports

10BASE-T/100BASE-TX Fast Ethernet and complies with

the electrical and protocol requirements of the PCI Local

Bus Specification, revision 2.2. The Wake-On-LAN feature is

optional for the adapter.

1.1 Features

The 10/100 Fast Ethernet PCI adapter is a cost effective,

high-performance network interface card. It operates in

10BASE-T and 100BASE-TX modes and integrates easily

with Fast Ethernet hub and switch.

ŸIEEE 802.3 10BASE-T and 100BASE-TX standards

Ÿ32-bit bus master for high throughput and low CPU

utilization

ŸWake-On-LANfeature is optional for different

hardware version

ŸFull-duplex operation at both 10Mbps and 100Mbps

ŸSupports10/100Mbps auto-sensing capability

ŸRich diagnostic LED mounted on bracket for easily

viewing and troubleshooting

ŸSingle shield RJ-45 connector for using at either

Speed (Category 3, 4 or 5 UTP cable for 10Mbps

Operation, and Category 5 UTP cable for 100Mbps

Operation)

ŸPlug and Play Installation.

ŸTest program (include Wake-On-LANevents)

ŸNetwork drivers on the diskette for Windows95,98,

ME, NT,2000, XP, NetWare, SCO Unix and Packet

driver.

ŸFCC, CE certification

1.2 System Requirements

To use the adapter, you need the following components:

ŸA PCI master mode expansion slot that is compliant

with PCI bus specifications, revisions 2.2

ŸA 3.5-inch,1.44MB diskette drive

ŸThe following cables:

To operate at 10Mbps, a Category 3, 4, 5 UTP Cable

To operate at 100Mbps, a Category 5 UTP cable

2. Installation

This section describes how to install the adapter. For

connecting to the network, you must have the following:

1. Network adapter card installed to your computer.

2. Cabling (compatible with network topology)

3. Connect the Wake-On-LAN cable to the motherboard (If

the WOL function is supported on the adapter)

4. Software for the adapter card contains both configuration

utilities and drivers

2.1 Unpack and Inspect

Caution:

Under ordinary circumstances, this adapter card

will not be affected by static charge as may be

received through your body during handling of the

unit .In special circumstances where you may

carry an extraordinarily high static charge, it had

better reduce the charge by touching a ground

before handling the adapter card.

Open the shipping gift box and carefully remove all items. In

addition to this User’s Manual, please check the following

items:

ŸOne 10/100 Fast Ethernet PCI Adapter Card

ŸOne WOL cable (If adapter supports WOL function)

ŸOne 3.5”Drivers and Utilities diskette

ŸThis user’s Manual

Note:

If any of the listed items are missing, please

contact your distributor or reseller

2.2 Install the Adapter

1. Turn off the computer.

2. Remove the computer’s cover, in accordance with its

manual.

3. Insert the contact edge of the adapter card into the

connector of any available PCI Bus master expansion

slot. Press the card firmly into the connector to PCI slot.

Please make sure that the card’s contacts are fully

seated in the PCI slot.

4. Install the bracket screw that secures the card to the

Computer chassis.

5. Connect the WOL cable to the motherboard. (If adapter

supports WOL function)

6. Replace the computer’s cover.

7. Connect the CAT3 or CAT5 UTP cable to the RJ-45

network connector.

8. Remove [Drivers and Utilities] diskette from the PC

diskette drive.

9. Turn on the computer.

10. If the BIOS section of your computer’s boot program is

Plug and Play compliant, then at power up the BIOS will

configure any newly installed adapter automatically.

Note:

Due to some Plug-n-Play BIOS programs' problem, it

happens occasionally that a newly installed adapter is

assigned an Interrupt Number which is already used

by another device adapter. In such a case, the conflict

of Interrupt Number will cause faults in the behavior of

both devices. Then it is necessary to run the CMOS

Setup utility, and manually assign a non-conflict

Interrupt Number.

2.3 Connect Fast Ethernet

Category 5 UTP cable is required for Fast Ethernet

operation. The maximum cable run between the adapter and

the supporting hub is 300ft (100m). Make the network

connection by plugging one end of the cable into the RJ-45

receptacle of the adapter, and the other end into one port in

the hub.

2.4 Connect 10Mbps Ethernet

Category 3, Category 4, and Category 5 UTP cable, as well

as EIA/TIA 568 100 ohm STP cable, all qualification under

Ethernet cabling rules. The maximum cable length run

between this adapter and the supporting hub is 300 ft. Make

the network connection by plugging one end of the cable

into the RJ-45 receptacle of this adapter, and the other end

into the hub.

2.5 Drivers and Utilities Diskette

The [Divers and Utilities] diskette contains all the popular

operating system drivers.

ŸNovell NetWare(client /server)

ŸWindows NT 3.5, NT4.0/2000/XP

ŸWindows 95/98/ME

ŸMicrosoft Client (NDIS 2.0 DOS/OS2)

ŸWindows For Workgroup 3.11

Ÿ…. and so on

2.6 Software Installation

Please refer to“Quick Installation Guide”

2.7 Test Program

This test program verifies configuration of the adapter and

assists the isolation of any faults in operation. Test

procedure are optional, and will only be useful in the unusual

event that there is a fault, such as an interrupt number

conflict among your computer’s add on cards, If your

installation provides normal operation, you do not need

these test procedures.

At your DOS prompt, type the following command:

a:\rset8139.exe <Enter>

The opening screen is displayed as following:

View Current Configuration

Set Up New Configuration

Run Diagnostics

Exit RSET8139

Choose<Set Up New Configuration>item allows you to

set up the Network Speed, 10 or 100M, and Transmission

Mode, Full or Half Duplex, and so on. Choose <Run

Diagnostics>item to run the adapter test program.

Adapter test program includes:

<Run EEPROM Test>,

<Run Diagnostics on Board>,

<Run Diagnostics on Network>, and

<Run Power Management Test>.

The <PowerManagementTest>is available for WOL

adapter only.

After choosing the <Run Diagnostics on Board>item, the

screen will display like,

Node ID........: 00 e0 7d c0 00 01

Network Speed..: 100Mbps

I/O Base ......: E000H

Interrupt .....: 11

Full-Duplex ...: Disabled

Pass Count Fail Count

A. I/O Register

B. 100Mbps Loopback

C. 10Mbps Loopback

D. Cable Connection

<Cable Connection>test reminds you that the connection

link might be fail, either the cable isnot connected orthe

cable link fails.

For the <Run Diagnostics on Network>test, it is

necessary to connect your computer with its supporting hub

or anothercomputer. This is a "Ping-Pong" test. This test

cannot becompleted except two computers on the LANfor

sending or receiving the test packets between computers.

For the <Run Diagnostics On Network>test

Master Machine: Master machine sends magic packet or

Wake up frame through the network.

Target Machine: Target machine is notified whenever a

qualified wakeup packet is received.

Network

Ethernet Address

00E07DC00002

TargetMachine

Ethernet Address

00E07DC00001

Master Machine

To wake up Target Machine with Magic Packet

Step1: Target Machine:

Target Machine is necessary to use the WOL cable

link the Wake On LAN connector on adapter with your

motherboard. Check BIOS <POWER MANGEMENT

SETUP> ACPI, Wake On LAN function must be

enable.

Step2: Target Machine:

Select <Target Machine> then the system will setup

wakeup event and wait a magic packet to do system

wakeup

Step3: Master Machine:

Select <Magic Packet> to send a magic packet and

wake up the target machine. The MAC address of

target machine will be asked for key-in, like

00 e0 7d c0 00 02.

Step4: Target Machine:

ACPI Testing events will be show

Device State 1: PASS

Device State 2: PASS

Device State 3: PASS

Step5: Target Machine:

Put the Target Machine to power down mode.

Step6: Master Machine:

Send a magic packet to wake up Target Machine.

Test the Wakeup Frame

Step1: Target Machine:

Select <Target Machine> then the system will setup

wakeup event and wait a magic packet to do system

wakeup

Step2: Master Machine:

Select<WakeUp Frame> to send a wakeup frame.

Step3: Target Machine :

ACPI Testing events will be show

Device State 1: PASS

Device State 2: PASS

Device State 3: PASS

Note:

Adapter testing program can not be used in Windows

95/98 DOS mode. Do not load any device drivers,

memory manager, and anti-virus software. The testing

program only can work in clean DOS prompt.

Quick Installation Guide

Please take the following steps for driver installation.

Microsoft Windows 95/Windows 98/WindowsME

1. Turn off the computer.

2. Insert the adapter into the available PCI slot.

3. Restart the computer.

4. After Microsoft Windows reboot, the PCI Ethernet

Controller will be found.

5. The system will prompt for driver installation.

6. Insert the“Driver and Utilities”diskette into diskette driver

and press <Enter>.

7. For Windows 95, Key in a:\ path to install driver for the

adapter

8. For Windows 98, Key in a:\w98_2000 path to install driver

for the adapter

9.For Windows ME, Key in a:\w inme path to install driver for

the adapter

10. The Windows system will install the driver automatically.

11. Reboot the Windows system.

Windows NT

1. Turn off the computer.

2. Insert the adapter into the available PCI slot.

3. Restart the computer.

4. Click “Start”menu bar and select“Setting”item then

“Control Panel”setting

5. Select“Network”icon

6. If this is the first time to install network on the machine

then the system will ask“YES”or“NO”to install network

adapter. Please select“YES”

7. If the computer already install network before then you

need to select“Interface”->“Add”

8. The system will prompt for driver installation.

9. Insert the“Driver and Utilities”diskette into diskette driver

and press <Enter>.

10. Key in a:\winnt path to install driver for the adapter

11. The Windows system will install the driver automatically.

12. Reboot the Windows system.

Andere Handbücher für KF-310

Inhaltsverzeichnis

Andere KTI Networks PCI-Karte Handbücher

KTI Networks

KTI Networks KE-PCI/T Bedienungsanleitung

KTI Networks

KTI Networks 100Base-FX Fast Ethernet PCI Adapter KF-221FX... Bedienungsanleitung

KTI Networks

KTI Networks KF-221FX series Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

KTI Networks

KTI Networks Gigabit Ethernet PCI Adapter KG-502T Bedienungsanleitung

KTI Networks

KTI Networks KF223TX Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung