SIIG SC2475 Bedienungsanleitung

Introducing Your Fast SCSI Pro

Your Fast SCSI Pro is a high performance, Plug-and-Play PCI-bus

master SCSI host adapter which supports connectivity to up to

sevenexternalSCSIdevices.Thesedevicesinclude:harddisks,tape

drives, removable/MO drives, optical drives, CD-ROMs, CD-R/

RWs, scanners and more.

Designed for use in PCs and MACs with PCI-bus slots. Your

Fast SCSI Pro supports 32-bit data transfer across the PCI bus at

speeds up to 133 MBytes per second. It supports synchronous data

transfer rates up to 10 MBy/sec, and is fully backward compatible

with all SCSI-1 devices.

The Fast SCSI Pro isdesignedfor addingonly externalSCSI devices

toyoursystem. Itdoesnotincludeanon-boardBIOStosupportthe

boot-up function; therefore, it must coexist with an IDE or other

hard disk controller.

Key Features and Benefits

•Supports up to 7 external SCSI devices simultaneously

including: jaz/zip drives, SyJet/ezflyer drives, CD-R/RW

drives, scanners, tape drives, MO drives, removable drives,

optical drives, WORM drives, jukeboxes and more

•Supportsburstdatatransferrates(synchronous)upto10MB/

sec

•Non-BIOS Fast SCSI-2 host adapter--designed for external

SCSI device connections

•Supports 133MB/sec burst data transfer rate on the PCI bus

•Works with various types of external Fast SCSI-2 devices

including hard disks, tape drives, removable/MO drives,

optical drives, CD-ROMs, CD-R/RWs, scanners, and more

•Full multitasking and multithreading support

•Bus Mastering achieves greater performance than PIO data

transfer method

•Advanced scatter/gather, disconnect/reconnect and tag

command queuing features maximize system performance

Fast SCSI Pro

Quick Installation Guide

04-0177A

•Active termination ensures error-free data transfer

•Connector type:

- External: One high-density 50-pin

System Requirements

For PCs:

•Pentium-Class computers with one available PCI slot

•Windows 3.1x/95/98/98SE/2000/NT4.0

For MACs:

•Power MacTM G3 or Mac®computer with one available PCI

slot

•MAC OS 8.1 or higher

Software Installation

Thefollowingsectionsdescribetheproceduresforinstallingdrivers

to enable your Fast SCSI Pro to operate properly under specific

operating system environments.

The Fast SCSI Pro is designed for adding only external SCSI devices

toyoursystem. Itdoesnotincludeanon-boardBIOStosupportthe

boot-up function; therefore, it must coexist with an IDE or other

hard disk controller. Drivers support for DOS, Windows 3.1x,

Windows 95, Windows 98/98SE, Windows 2000, Windows NT4.0,

and MAC OS are provided.

Driver Installation for PC Systems

IMPORTANT

It is important that the SCSI bus hardware and

operating system are installed correctly before

proceeding further.

DOS/Windows 3.1 Driver Installation

Perform the following steps to install the driver for the MS-DOS/

Windows 3.1x operating system:

1. Insert the Driver & Utility CD into your CD-ROM Drive.

(Assuming D: is your CD-ROM drive).

2. Goto the folder "D:\AP-10_20\DOSWIN31" and copy all of the

files in that folder (except the "image" folder) onto a floppy

diskette.

3. Turn on your computer to boot to the DOS prompt.

4. Insert the floppy diskette you have just made into the floppy

drive.

5. At the a:> prompt, type: install and press <Enter>.

6. Press<Enter>tocontinueand press<Enter>again toauto intall

the driver on your hard disk.

(“Automatic Installation” is the default setting for driver

installation and is highly recommended on most cases)

Thedriverinstallationis complete. Removethedisketteand follow

the screen instruction to reboot the system.

Windows 95 Driver Installation

Follow the procedures listed below to install Windows 95 drivers:

1. WhenWindowsfirstrestartsafterinstallingtheSCSIcontroller,

it will inform you that New Hardware Found. Insert the Drivers

and Utility CD-ROM into the CD-ROM drive.

2. Click “Next” for Update Device Driver and click on the "Other

Locations" button.

3. Type in the path: "D:\AP-10_20\WIN95" and press "Enter".

(Assuming D: is your CD-ROM drive).

4. Click “OK”, type in the installation path from Step 3 again

when prompted, click on “OK”, and “Finish”.

5. Select “YES” to restart your system.

Windows 95 driver installation complete, the controller is now

ready for device connection.

Windows 98/98SE Driver Installation

Windows98and98SE willauto-detect thecontroller andinstall the

correct driver automatically. Please insert your Windows 98 CD

into your CD-ROM drive when prompted.

Windows 2000 Driver Installation

Windows 2000 will auto-detect and install the correct driver for the

Fast SCSI Pro controller. Insert Windows 2000 CD into your CD-

ROM drive when prompted.

Restart your system if prompted by Windows. Driver installation

is complete, the controller is now ready for device connection.

Windows NT 4.0 Driver Installation

Thefollowinginstructionswillguideyouthroughtheinstallationof

Windows NT driver for computer systems that boot from an IDE

drive or other SCSI host adapters.

1. Once a Windows NT session is established, perform the

following steps:

• Select “My Computer” from the Main Desktop.

• Select “Control Panel”from the My Computer group.

• Select “SCSI Adapters” from the Control Panel group.

2. Select the “Drivers” tab and click on “Add…”

3. From the Install Driver window, click “Have Disk...”.

4. Insert the Driver and Utility CD into your CD-ROM drive.

5. Type in the path: "D:\AP- 10_20\WINNT" and click "OK".

Select the driver name: "AdvanSys PCI SCSI Host Adapter"

and click "OK". Type in the path: "D:\AP-10_20\WINNT"

again and click "Continue..." to install the driver into your

Windows NT 4.0 system.

(Assuming D: is your CD-ROM drive).

6. Select "Yes" to re-start your system.

Windows NT 4.0 driver installation is complete. The controller is

now ready for device connection.

Driver Installation for MAC Systems

AnubisdiskmountingandCD-ROMutilitiesareincludedtomount

the hard disks and the CD-ROMs.

Perform the following steps to install the drives:

1. Start up your MAC computer.

2. InserttheDriversandUtilityCD-ROMintotheCD-ROMdrive.

3. Double click on "SIIG_SCSI" CD-ROM Icon

4. Double click on "Anubis Extension Installer" program icon

5. Click on "Install" to begin the installation process

6. Oncethe"Installationwassuccessful"screenisdisplayed,click

on "Quit" to complete the process

7. The installation program will prompt you to install the

AutoCache and CD-ROM Extension Installer.

- If you are attaching a CD-ROM/R/RW to the SCSI controller,

click on "Install" to continue and proceed to Step 8.

- If you are NOT attaching a CD-ROM/R/RW to the SCSI

controller, click on "Quit" and proceed to Step 10.

8. Once the "Installation was successful" screen is displayed,

click on "Quit" to complete the process.

9. TheinstallationprogramwillpromptyoutoinstalltheAcrobat

Reader Installer. Click on "Continue".

- If you already have Acrobat Reader installed, click on

"Decline" and proceed to Step 10.

- Otherwise, click on "Accept" and follow the on-screen

instructions to complete installation for Acrobat Reader.

Then proceed to the next step.

10. Double click on "SIIG_SCSI" CD-ROM icon located on your

MAC OS desktop.

11. Locate the file "AdvanSIM" and copy it to the "Extensions"

folder.

Note The"Extensions"foldercanbefoundinthe"System"folder

under your Main Hard Drive.

12. Restart the MAC computer for the new settings to take affect.

The software installation is now complete.

Using the Utility

The following utilities are located on the "SIIG_SCSI" CD-ROM. If

you need further information on the bundled utilities, please refer

to the Anubis_Manual.pdf file.

a) AnubisUtilityv3.07-A: Thisisa fullfeaturedutilitythat allows

you to format, partition, mount, and initialize SCSI devices.

b) Anubis Mounter v3.07-A: This utility allows you to mount,

unmount, and perform limited configurations on the selected

drive or bus.

c) Reader 3.1 Installer: This utility installs the Acrobat Reader.

Connecting External SCSI Devices

You can connect up to seven external SCSI devices to your

Fast SCSI Pro board.

NOTES

•Do not connect differential SCSI devices; use only

single-ended SCSI devices. (Unless specified, SCSI

devices you see in the store are all single-ended).

•Itisimportantthatyoualwaysusehigh-qualitydouble

shielded twisted-pair external cable.

The combined length of all cables is limited to up to 6

meters (19.8 feet).

1. ConfigureeachSCSIdevice,suchasascannerorCD-R/RW

drive according to the manufacturer’s instructions.

a. Follow the rules for terminating SCSI devices. The

Fast SCSI Pro and the last device connected on the

SCSI bus chain should be terminated.

b. Verify that the default SCSI ID number set on each

device is unique. If there is a conflict, reset it to an

available ID (0-6, assuming board default of ID 7)

following by the manufacturer’s instructions.

2. Attach one end of a SCSI cable to the external connector

on the Fast SCSI Pro and the other end to your SCSI

device.

Note TheFastSCSIProrequiresacablewithamalehigh-

density50-pin (HD50)connectoron oneend.The typeof

connector on the other end depends on the external

device you plan to connect.

If you are connecting more than one device, connect the cables

between the SCSI devices in a daisy-chained configuration.

ABP940

Host Adapter

Card

End of SCSI Bus

TERMINATION

AUTOMATICALLY

ENABLED

End of SCSI Bus

TERMINATION

ENABLED

TERMINATION

Maximum 7 SCSI

Periperal Devices

Installable With One

ABP940

Device

External SCSI

Devices

Device

Termination

OFF

Termination

OFF

End of SCSI Bus

Termination ON

Fast SCSI Pro

Factory Set

Termination ON

Figure 1. Connecting External Devices

Return Merchandise Authorization (RMA)

SIIGwarrants totheoriginal buyerof theproduct thatthehardware is

freeof defectsin materials andworkmanship fora periodof fiveyears

from the date of purchase. If your product fails to be in good working

order during the warranty period, you may return it to SIIG for repair

or replacement at SIIG's option. To return a product:

Step 1: Call SIIG's RMA Department

Call the RMA Department at (510)413-5333 for a Return Merchandise

Authorization(RMA)number.TogetaRMAnumber,youmusthave

yourproductserialnumber.Theserialnumberislocatedontheside

of the box it came in and on the back of the product.

Step 2: Complete the RMA form

• Fill out the RMA form and include it with the product.

• Properly pack the product for shipping. All software, cable(s) and

accessories that came with the original package must be included.

• ClearlywriteyourRMAnumberonthetopofthereturnedpackage

andontheaccompanyingRMAform.SIIGwillrefuseanyshipping

package,and notbe responsiblefor aproductreturnedwithouta

RMA number posted on the outside of the shipping carton.

Step 3: Ship the product

You are responsible for the shipping cost to SIIG at the following

address: SIIG, Inc. RMA#_______________

6078 Stewart Ave.

Fremont, CA 94538

SIIGwillshiptherepairedorreplacedproductviaUPSGroundor US

Mail at no cost to you.

Technical Support & RMA

Questions? SIIG’s Online Supporthas the answers! Simply visit our

web site at www.siig.com and click on the ONLINE SUPPORT icon

for instant technical support. You may also e-mail us onlineat:

http:\www.siig.com/technical_support_form.html

If you need additional help, Tech Support Specialists are available

from 8:00 a.m. to 5:00 p.m. Mon. – Fri., PST at (510) 353-7542.

In order for SIIG’s Technical Support to give you prompt service, you

will need the following information.

Part Number: ______________________________________

Computer Configuration: ____________________________

PRODUCTNAME MODELNUMBER

Fast SCSI Pro SC2475

FCC RULES: TESTED TO COMPLYWITH FCC PART 15, CLASS B

OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a

ClassB digital device,pursuanttopart15ofthe FCC Rules.Theselimitsare

designed to provide reasonable protection against harmful interference in a

residentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio

frequency energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticular

installation. If this equipment does cause harmful interference to radio and

television reception, which can be determined by turning the equipment off

andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormore

of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio or TV technician for help

Caution:

Any changes or modifications not expressly approved by the party

responsibleforcompliancecouldvoidtheuser'sauthoritytooperate

this equipment

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

(510) 657-8688

Fast SCSI Pro is a trademark of SIIG, Inc.

Microsoft and Windows are registered trademarks of Microsoft Corporation .Mac is a

registered trademark of Apple Corporation. Pentium is registered trademark of Intel

Corporation. All other trademarks belong to their respective holders.

Inhaltsverzeichnis

Andere SIIG PCI-Karte Handbücher

SIIG

SIIG NN-400M12-S6 Bedienungsanleitung

SIIG

SIIG SC-SA2012-S1 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCIe Bedienungsanleitung

SIIG

SIIG SIIG 2S1P Combo-Value Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Bedienungsanleitung

SIIG

SIIG JJ-P02D11-S6 Bedienungsanleitung

SIIG

SIIG CyberPro PCI 4S Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

SIIG

SIIG Duet Parallel PCI Bedienungsanleitung

SIIG

SIIG JU-P40112-S1 Bedienungsanleitung

SIIG

SIIG DP 4-Port USB 3.0 PCIe i/e Bedienungsanleitung

SIIG

SIIG PCI-to-PC Card Pro Bedienungsanleitung

SIIG

SIIG SC-SA1012-S1 Bedienungsanleitung

SIIG

SIIG JJ-P02012 Bedienungsanleitung

SIIG

SIIG SC-SAE212-S2 Bedienungsanleitung

SIIG

SIIG RS232 Serial Bedienungsanleitung

SIIG

SIIG JJ-P00212-S6 Bedienungsanleitung

SIIG

SIIG Low Profile USB 2.0 Bedienungsanleitung

SIIG

SIIG Low Profile PCI I/O Bedienungsanleitung

SIIG

SIIG Serial ATA PCI Bedienungsanleitung

SIIG

SIIG SoundWave 5.1 PCI-LP Bedienungsanleitung

SIIG

SIIG 1394 PCI Adapter Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 4-Port PCI Bedienungsanleitung

SIIG

SIIG Cyber 1S1P PCI Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung

Alpha Networks

Alpha Networks WMP-A13V Bedienungsanleitung