Kwikset 907 15 SMT Bedienungsanleitung

19701 DaVinci

Lake Forest, CA 92610

1-800-327-5625

www.kwikset.com

A Black & Decker Company

Printed in the USA

Touchpad Electronic Deadbolt

Installation & Learning Instructions

Owner’s Manual

Part No: 40486 / 02

Table of Contents

Enclosed Pieces Page 1

1 Door Preparation Page 2

2 Deadbolt Latch Installation Page 2

3 Strike Installation Page 3

4 Touchpad Electronic Deadbolt Installation Page 4

5 Programming Instructions Page 6

6 Proper Operation of Touchpad Electronic Deadbolt Page 7

Notes and Warranty Page 8

Troubleshooting Tips Page 9

Pieces

Touchpad

Latch

Strike

Keys

Deadbolt

Mounting Plate

Power Strip

Power Board

Access Cover

Important Notes:

Use the components from this

package, make no substitutions.

Consult local building codes for

requirements in your area.

Read all instructions and lay out

parts as shown.

Under normal use it is recom-

mended to replace the batteries in

the Power Board once a year.

D E F

T-TURN

Enclosed Pieces

2. Deadbolt Latch Installation (Piece B)1. Door Preparation

Replacement Installation

Remove all old lock

components.

Use the enclosed template

to verify the following:

Deadbolt face hole needs to

be 2-1/8” (54mm) diameter.

Backset – Distance from

edge of door to center of

lock (2-3/8 or 2-3/4”).

Location to drill the small starter holes for

inside and outside trims.

Make any necessary modiﬁcations.

First-time Installation

Follow instructions on enclosed template.

Preparation for latch with Face Plate

Keeping edges parallel to the face of the door,

outline face plate and remove deadbolt latch

(see illustration below left).

Chisel outline of face plate until it is ﬂush with

door edge, 5/32” (4mm) deep (see illustration

below right).

With bolt extended, insert deadbolt latch in

edge hole. Be sure to keep the word "UP" at

top. Secure with two 5/8” wood screws.

Install Latch

•

For latch with face plate:

To Adjust Backset:

Rotate to a 2-3/4” (70mm)

position, if required.

2. Deadbolt Latch Installation (Piece B) 3. Strike Installation (Piece C)

With bolt retracted, insert deadbolt latch into

edge hole keeping ﬂat edge of bolt parallel to

the edge of door. Be sure to keep the word

"UP" at top.

Using a wood block, tap with hammer until

surface of collar is ﬂush with door edge

Re-extend bolt.

First-time Installation

Draw a horizontal centerline across the door

jamb, the same distance from ﬂoor as is the

centerline of deadbolt latch.

Measure back from door stop, 1/2 the

distance of the door thickness and draw a

vertical centerline. At crosspoint, drill a 1-1/8”

diameter (28.5mm) hole,1-1/4” (29mm) deep,

in the door jamb.

Center strike over hole and trace around

strike. Chisel out door frame until strike is

ﬂush.

Position strike with large holes toward door

stop. Pre-drill large holes 3” (76mm) deep.

Important Note:

Deadbolt latch must enter strike

with no resistance or the Power-

bolt Touchpad Electronic Deadbolt

will not work properly.

U P

Door

Jamb

1/2 of door

thickness

Door

Stop

For Drive-In latch:

Install strike

Install 3” (76mm) screws in large strike holes

and install remaining 5/8” wood screws in

smaller holes.

Close door and ensure bolt extends and

retracts freely.

4. Touchpad Electronic Deadbolt Installation

With bolt of latch in the extended position,

place Touchpad Aon outside of door and

place power strip Gthrough door over top

of latch B. Note: Do not remove backing

from Touchpad.

With key removed, place deadbolt Eagainst

Touchpad A with round of torque blade at top

to enter through crank of latch B.

Attach deadbolt with 2 large black bolts

through mounting plate Fas shown. Power

strip Gshould extend out.

123

Line Touchpad Aup with small holes from

template and attach with two 1” oval head

screws. Do not over-tighten screws.

Round

Crank

4. Touchpad Electronic Deadbolt Installation

Feed power strip Gthrough large square hole

of Power Board Hand plug into the 6 prongs.

Line Power Board Hup to the 3 small holes

drilled from the template. Verify that torque

blade engages with the T-turn and attach

power board with 3 chrome-colored screws.

Remove access cover I from Power Board H.

Hold as shown in photo and twist or pull up

on cover.

5 6 7 Install 4 new AA Alkaline batteries (not

included in package). Battery positions shown

on battery case. A series of quick beeps will

sound when batteries make complete contact.

Low Battery Indicator Light on the Power

Board will be lit when the batteries need to be

replaced.

Do not dispose of in ﬁre, recharge, put in

backwards, disassemble, mix with used or

other battery types. May explode or leak and

cause personal injury.

4. Touchpad Electronic Deadbolt Installation 5. Programming Instructions

Push program button on Power Board H once.1

Retract deadbolt latch Bwith T-turn. Press the lock button on Touchpad A. If motor runs but

latch does not extend: Door handing needs to be changed. To change door handing, remove

jumper (located in the upper right corner of the circuit board) from position "A" and plug it into

position "B". See illustrations.

Verify key works in deadbolt E.

Note: When manually locking or unlocking the deadbolt by turning the key or the T-turn:

The motion will be rm — this resistance is normal.

Enter desired 4 to 8 digit code by pressing

numbers on outer Touchpad A. Press the

Lock button on Touchpad to set your code.

You will hear a 2-second long beep when your

code is accepted.

If unit does not

beep — too much

time has elapsed

between steps

1 and 2. Repeat

steps 1 and 2

faster.

From Exterior:

If hinge is on the left, you

have a left hand door.

If hinge on the right, you

have a right hand door.

Exterior

Right hand

Door

Left hand

Door

•

5. Programming Instructions 6. Proper Operation of Touchpad Electronic Deadbolt

To Enter Second Code

Push program button twice, then repeat steps

2-4.

5Push the Lock button on outside touch pad to

extend latch bolt 1” which locks the door when

you leave.

Enter your desired personal code to retract

the latch bolt completely which unlocks the

door when you return home.

The T-turn on the inside of the door is used to

extend (lock) or retract (unlock) the latch bolt

when you are inside.

Using the key from the outside will also extend

(lock) or retract (unlock) the latch bolt.

This Touchpad Electronic Deadbolt should be

accompanied by a Kwikset Knobset, Leverset,

or Handleset.

Enter your number to verify that it retracts

the latch B.

4Snap access cover I onto power board H.

Align cover to top of power board and press

down at the bottom of the cover (see illustra-

tion below). To coordinate with your home

decorating scheme, the access cover may

be painted to

match your

door.

CAUTION: Prevent unauthorized

entry. This lock can be opened

using two different codes that are randomly

set at the factory. Upon installation and

set-up, replace both of these codes with

your own. Since anyone with access to the

power board can change these codes, you

must restrict access to the power board

and routinely check both codes to assure

they have not been altered without your

knowledge.

Important — Please Read Warranty Manufacture's note.

Under normal use it is recommended to

replace the batteries once a year. When

batteries are low, it will take longer to retract

the bolt. Batteries should be changed im-

mediately!

Lower latch must hold shut allowing deadbolt

latch to enter strike freely with no restrictions.

If door is misaligned, make necessary adjust-

ment to deadbolt strike location and/or hole

in door jamb to allow the deadbolt latch to

retract and extend freely.

Reprogramming of codes should not be

necessary after changing batteries.

If required, key can be used to retract

deadbolt.

If interior trim is exposed to extreme cold

temperatures, the batteries will not operate.

This is typical of all batteries and not a mal-

function of the lock.

•

WARNING: This Manufacturer

advises that no lock can provide complete

security by itself. This lock may be defeated

by forcible or technical means, or evaded

by entry elsewhere on the property. No lock

can substitute for caution, awareness of your

environment, and common sense. Builder’s

hardware is available in multiple performance

grades to suit the application. In order to

enhance security and reduce risk, you should

consult a qualiﬁed locksmith or other security

professional.

Full Lifetime Finish Warranty

Full Lifetime Mechanical Warranty

One Year Limited Electrical Warranty

This Warranty states all mechanical lock

parts will be free from defects in material and

workmanship, including deterioration over time

of ﬁnish on the exterior lock components while

the original purchaser owns the lock.

All electrical components are covered by a

One Year Limited Warranty.

Our warranty excludes locks that have been

damaged by installation contrary to our written

instructions or modiﬁed with non-Kwikset

components. It also excludes incidental

or consequential damages. (Some states

do not allow the exclusion or limitation of

incidental damages so this exclusion may

not apply to you.) To register a warranty

claim, please return the product, freight

prepaid to Attn: Consumer Services, Kwikset

Corporation, 19701 Da Vinci, Lake Forest,

California 92610. Kwikset will repair or replace

the lock or refund the purchase price (if it is

not practical to repair or replace). You will be

responsible for the removal of the old lock and

the installation of the new one.

This Warranty provides you with speciﬁc legal

right and you may also have other rights which

vary from state to state.

Inhaltsverzeichnis

Sprachen:

Andere Kwikset Türschloss Handbücher

Kwikset

Kwikset Camino Pull Bedienungsanleitung

Kwikset

Kwikset Signatures Lisbon 157LSL SQT 26 Bedienungsanleitung

Kwikset

Kwikset 62822/01 Bedienungsanleitung

Kwikset

Kwikset Prismo 740PSK RDT 15 SMT Bedienungsanleitung

Kwikset

Kwikset Smartcode 888 Bedienungsanleitung

Kwikset

Kwikset SMARTCODE Bedienungsanleitung

Kwikset

Kwikset Kevo Bedienungsanleitung

Kwikset

Kwikset Powerbolt 2 Bedienungsanleitung

Kwikset

Kwikset Smartcode 914 Bedienungsanleitung

Kwikset

Kwikset 665 Bedienungsanleitung

Kwikset

Kwikset 00883351666312 Bedienungsanleitung

Kwikset

Kwikset Burbank Bedienungsanleitung

Kwikset

Kwikset SMARTCODE 917 Bedienungsanleitung

Kwikset

Kwikset Powerbolt 2 Bedienungsanleitung

Kwikset

Kwikset CP/BP 49726 / 02 Bedienungsanleitung

Kwikset

Kwikset 69925-001 Bedienungsanleitung

Kwikset

Kwikset SMARTCODE 9260CNT-514S Bedienungsanleitung

Kwikset

Kwikset Aura Bedienungsanleitung

Kwikset

Kwikset Kevo Bedienungsanleitung

Kwikset

Kwikset Smartcode 914 Bedienungsanleitung

Kwikset

Kwikset Smartcode 910 Bedienungsanleitung

Kwikset

Kwikset 818 Bedienungsanleitung

Kwikset

Kwikset Kevo Bedienungsanleitung

Kwikset

Kwikset 62883-002 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung