5
• Warning! High pressure jets can be dangerous when the
machine is not use properly. Do not direct the jet toward
persons, animals, live electrical equipment or the device
itself.
• Do not direct the jet against yourself or others in order to
clean clothes and footwear.
• Children should be supervised to ensure that they do not
play with the machine.
• This machine is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, “High
pressure cleaners shall not be used by children or un-
trained personnel.”
• Warning! Spray gun hoses, fittings and couplings are
important components for the safety of the device. Only
use spray gun hoses, ttings and couplings that are rec-
ommended by the manufacturer.
• In order to ensure the operational safety of the device,
only use genuine manufacturer’s replacement parts or
parts that have been approved by the manufacturer.
• Do not operate the device if the mains cable or other
important parts of device – e.g. safety related elements,
spray gun hose, spray gun – are damaged.
• Do not pull or carry the electric tool by its mains cable.
Protect the mains cable from becoming damaged by oil,
solvents and sharp edges.
• Keep your place of work tidy.
• Ensure that the switch is turned o when connecting the
machine to the power supply.
• Wear the suitable work clothes.
• Check your machine to ensure that it is in good working
order. If it is not functioning properly, have it checked
by our authorized distributor. Have all maintenance and
inspection work carried out only by our authorized dis-
tributor.
• The water jet discharged from the nozzle lance produces
a ‘kickback’ on the spray gun. Therefore, make sure that
you have a solid footing and that you have a rm hold of
the handle grip. In order to protect yourself from possible
ying objects (that are released due to the high pressure).
• The high pressure jet can damage vehicle tyres and tyre
parts. Keep a distance of at least 30 cm from the object
being cleaned.
• If there is a power failure while you are using the machine,
be sure to switch o the machine for safety reasons.
• The electric pump always must be able to draw on a
sucient supply of water. Dry operation causes severe
damage to the seals.
• Disconnect from the power supply before carrying out
user maintenance.
• Only use genuine spare parts from the manufacturer or
approved by the manufacturer.
• If the supply cord is damaged, it must be replaced by our
authorized distributor in order to avoid a hazard.
• Never use the machine in an environment where there
could be a danger of explosion. If any doubt arises,
please contact our authorized distributor.
• It is not allowed to clean asbestos-containing surfaces
with high pressure.
• This machine must not be used at temperatures below
0°C.
• The electric supply connection (for example, connection
the RCD or x wiring) shall be made by a qualied elec-
trician and comply with IEC60364-1: Low-voltage electri-
cal installations.
Safety devices
Safety lock on spray gun
The spray gun features safety lock button (19). When the
lock is activated, the spray gun cannot be operated.
Motor pump protection
The motor is equipped with a motor circuit breaker switch.
When the motor starts to run hot, it is cut out automatically
by this switch. Switch o the machine. Wait 5 ~ 10 minutes
before using the device again. Try to determine the cause
of the fault. If the problem repeats itself, please contact our
service centre.
Operating instructions
Purpose
The machine is designed to clean vehicles, machines,
buildings, facades, etc. in the private sector.
Areas of application
• Never use the machine in potentially explosive areas
under any circumstances!
• The operating temperature must be between 0°C and
+40°C.
• The machine consists of an assembly with a pump,
which is encased in a shock absorbing housing. For
an optimal working position the machine comes with
a lance and a non-slip handle grip, whose shape and
conguration comply with the applicable regulations.
• Do not cover or modify the lance or the spray nozzles in
any way.
• The machine is designed to be used with cold or
lukewarm (max. 40°C); higher temperatures can damage
the pump.
• Do not use water that is dirty, gritty or contains any
chemical products, as these could impair operation and
shorten the life of the machine.
Assembly
*Tools needed for assembly: Water supply hose, Hose
clamp, Phillips screwdriver.
*The water supply hose must have an internal diameter of
at least 13mm (1/2 in.) and must be reinforced. The water
supply must be at least equal to the washer delivery
capacity.
1. Screw the handle (2). (Fig.2)
2. Fit the cord hook (4) into the hook (24). Power cord can
be hung. (Fig. 3)
3. Fit the spray gun holder (3) into the hook (23). Spray
gun (9) can be stored. (Fig. 4)
4. Connect the wheel (5) and wheel cover (6) to the unit.
(Fig.5)
5. Connecting the nozzle lance to the spray gun. (Fig.6)
Fit the nozzle lance (7 and 8) into the spray gun (9) and
rotating it until the two parts are completely locked.
Test the connection by pulling on the nozzle.
6. Connect the spray gun hose (10) to the spray gun (9).
(Fig.7)
WARNING! Water leakage may occur if the hose is not
secured properly or if the connectors are not free from
dirt and debris prior to connecting.
