Kyocera RYOBI AJP-800 Bedienungsanleitung

69800384-00 KAP

04-20

AJP-800

2 3 4

18 8

7 8 9

10 12

Preparation

Before starting up your machine, we advise you to carefully

read through this instruction manual. Follow all instructions

to minimize the risk of injuries when using the machine.

Prior to operation

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine and

contact your distributor.

Especially check:

The insulation of the electric cable should be faultless and

without any cracks. If the electric cable is damaged, it should

be replaced by our authorized distributor.

Mains power supply connection

The following should be observed when connecting the

machine to the electric installation:

• Check before operation that the local power supply is the

same as the specications on the rating label.

• This machine is equipped with universal motor with double

insulation. It is not necessary to have earth connection.

• The electric installation shall be made by a certified

electrician.

• It is strongly recommended that the power supply to the

machine should include a residual current device (RCD).

• Product protection degree:IPX5

General safety regulations and accident

prevention

It is essential that you read the safety regulations and

operating instructions in their entirety and follow the

information contained therein in order to eliminate the

possibility of an accident or potentially dangerous situation

from occurring while working with the machine.

• The power plug must be plugged into a properly installed

socket. The power supply should include a residual

current device for max. 30 mA.

• Always check the device, the mains cable and the plug

before using the machine. Only operate the device when

it is in good working order and has not been damaged in

any way. Damaged parts must be immediately replaced

by a qualied electrician.

• Always pull the power plug out of the socket outlet before

doing any work on the machine, before changing the

nozzle and whenever it is not being used.

• Warning! Inadequate extension cords can be dangerous.

• If an extension cord is used, it shall be suitable for outdoor

use, and the connection has to be kept dry.

• Only use suitable extension cable when working outdoors.

Extension cable must have a minimum cross-section of

1.5 mm2.

• Warning! This device was developed to be used with

cleaning agents supplied or recommended by the

manufacturer. The use of any other cleaning agents or

chemicals can negatively a󰀨ect the safety of the device.

• Cable connections should be kept dry and o󰀨 the ground.

Always uncoil the extension cable completely to avoid

heat damage to the cable.

• Warning! Do not use the device when other persons or

animals are in the near vicinity unless they are wearing

appropriate protective clothing.

Carefully read and understand these instructions

before operating this high pressure washer.

Package Contents (Fig.1)

1. Main unit

2. Variable nozzle lance

3. Mid nozzle lance

4. Spray handle

5. Spray handle hose (5m)

6. Water connector

7. Hose joint

8. Nozzle cleaning pin

9. Foam nozzle

Technical data

Power rating input 800 W

Rated pressure 60 bar (6.0 MPa)

Allowable pressure 90 bar (9.0 MPa)

Rated ow 4.8 L / min

Max. inlet water pressure 1.0 MPa

Max. temperature: 40℃

Adding water From a faucet

Weight 3.8 Kg

Sound pressure level

Uncertainty

LpA=76dB(A)

KPA=3dB

Sound power level LwA=92dB(A)

Vibration Value aH=1.8m/s2

Kah=1.5m/s2

Name of Parts:

1. Main unit

2. Variable nozzle lance

3. Mid nozzle lance

4. Spray handle

5. Spray handle hose

6. Water connector

7. Hose joint

8. Nozzle cleaning pin

9. Foam nozzle

10. Water supply hose (option)

11. Hose clamp (option)

12. Main switch

13. Safety lock button

14. Trigger

15. Power cord

16. Filter

17. Water inlet

18. Release button

• Warning! High pressure jets can be dangerous when the

machine is not use properly. Do not direct the jet toward

persons, animals, live electrical equipment or the device itself.

• Do not direct the jet against yourself or others in order to

clean clothes and footwear.

• Children should be supervised to ensure that they do not

play with the machine.

• This machine is not intended for use by persons (including

children) with reduced physical, sensory or mental capa-

bilities, or lack of experience and knowledge, “High pres-

sure cleaners shall not be used by children or untrained

personnel.”

• Warning! Spray handle hoses, ttings and couplings are

important components for the safety of the device. Only

use spray handle hoses, fittings and couplings that are

recommended by the manufacturer.

• In order to ensure the operational safety of the device,

only use genuine manufacturer’s replacement parts or

parts that have been approved by the manufacturer.

• Do not operate the device if the mains cable or other

important parts of device – e.g. safety related elements,

spray handle hose, spray pistol – are damaged.

• Do not pull or carry the electric tool by its mains cable.

Protect the mains cable from becoming damaged by oil,

solvents and sharp edges.

• Keep your place of work tidy.

• Ensure that the switch is turned o󰀨 when connecting the

machine to the power supply.

• Wear the suitable work clothes.

• Check your machine to ensure that it is in good working

order. If it is not functioning properly, have it checked by

an our authorized distributor. Have all maintenance and

inspection work carried out only by our authorized dis-

tributor.

• The water jet that emerges from the high pressure nozzle

produces a ‘kickback’ on the spray handle. Therefore,

make sure that you have a solid footing and that you have

a rm hold of the handle grip. In order to protect yourself

from possible ying objects (that are released due to the

high pressure).

• The high pressure jet can damage vehicle tyres and tyre

parts. Keep a distance of at least 30 cm from the object

being cleaned.

• If there is a power failure while you are using the machine,

be sure to switch o󰀨 the machine for safety reasons.

• The electric pump always must be able to draw on a

sufficient supply of water. Dry operation causes severe

damage to the seals.

• Disconnect from the power supply before carrying out

user maintenance.

• Only use genuine spare parts from the manufacturer or

approved by the manufacturer.

• If the supply cord is damaged, it must be replaced by our

authorized distributor in order to avoid a hazard.

• Never use the machine in an environment where there

could be a danger of explosion. If any doubt arises, please

contact our authorized distributor.

• It is not allowed to clean asbestos-containing surfaces

with high pressure.

• This machine must not be used at temperatures below 0℃

• The electric supply connection (for example, connection

the RCD or x wiring) shall be made by a qualied electri-

cian and comply with IEC60364-1: Low-voltage electrical

installations.

Safety devices

Safety lock on spray handle

The spray handle features safety lock button (13). When the

lock is activated, the spray handle cannot be operated.

Motor pump protection

The motor is equipped with a motor circuit breaker switch.

When the motor starts to run hot, it is cut out automatically

by this switch. Switch o󰀨 the machine. Wait 5 ~ 10 minutes

before using the device again. Try to determine the cause

of the fault. If the problem repeats itself, please contact our

service center.

Operating instructions

Purpose

The machine is designed to clean vehicles, machines, build-

ings, facades, etc. in the private sector.

Areas of application

• Never use the machine in potentially explosive areas

under any circumstances!

• The operating temperature must be between 0℃and +40℃.

• The machine consists of an assembly with a pump, which

is encased in a shock absorbing housing. For an optimal

working position the machine comes with a lance and

a non-slip handle grip, whose shape and configuration

comply with the applicable regulations.

• Do not cover or modify the lance or the spray nozzles in

any way.

• The machine is designed to be used with cold or

lukewarm (max. 40℃); higher temperatures can damage

the pump.

• Do not use water that is dirty, gritty or contains any

chemical products, as these could impair operation and

shorten the life of the machine.

Assembly

Tools needed for assembly: Water supply hose, Hose

clamp, Phillips screwdriver

*The water supply hose must have an internal diameter

of at least 13mm (1/2 in.) and must be reinforced. The

water supply must be at least equal to the washer delivery

capacity.

1. Connecting the nozzle lance to the spray handle. (Fig.2)

Fit the nozzle lance (2 and 3) into the spray handle (4)

and rotating it until the two parts are completely locked.

Test the connection by pulling on the nozzle.

2. Connect the spray handle hose (5) to the spray handle

(4). (Fig.3)

WARNING! Water leakage may occur if the hose is not

secured properly or if the connectors are not free from

dirt and debris prior to connecting.

3. Connecting the spray handle hose to the water

discharge nozzle (Fig.4)

Secure the spray handle hose (5) directly onto the water

discharge nozzle and turn the hose link clockwise to

connect.

Turn the hose link until it is secure.

WARNING! Jiggling the spray handle hose to the right

or left when connecting, may cause water to leak from

the connection area.

4. Screw the water connector (6) onto the water inlet (17).

(Fig. 5)

5. Attach the water supply hose (10) to the faucet (Fig. 6)

WARNING! Remove dirt and debris from the faucet and

from the outside and inside of the hose.

Allow the water from the faucet to run for a short time

before attaching the hose.

Dirt or debris entering the unit may cause damage to the

pump.

WARNING! Be sure to use water directly from the

water faucet. Hot water (over 40℃) and water from hot

springs may damage the unit.

Attach the water supply hose (10) to the water faucet

with the hose clamp (11).

Tighten the clamp screw to secure the hose to the

faucet.

6. Attaching the hose joint to the water supply hose (Fig.7)

Loosen and remove the hose link from the hose joint

(7).

Insert the water supply hose (10) through the hose link.

Insert the end of the water supply hose securely into the

connecting portion of the hose joint.

Securely tighten the hose link onto the hose joint by

turning the hose link clockwise.

WARNING! There is a valve attached to the hose joint.

Water will not ow out of the hose until it is attached to

the water connector.

7. Connecting the hose joint to the water connector

(Fig.8)

Push the hose joint (7) onto the water connector (6) until

you hear a 'click' sound.

WARNING! Jiggling the water supply hose to the right

or left when attaching may cause water to leak from the

connection area.

Operating the Switch (Fig.9)

Turning the main switch (12) clockwise to the "ON" position

starts the unit. Returning the switch to the "OFF" position

cuts electrical power to the unit.

Using the Spray Handle (Fig.10)

Pulling the spray handle trigger (14) releases a highly

pressurized water ow. Releasing the trigger stops the ow.

The spray handle safety lock button (13) prevents accidental

operation.

When locked, the trigger cannot be depressed.

Nozzle Lance (Fig. 11)

Changing the spray di󰀨usion (narrow ⇔wide)

Change the spray di󰀨usion by turning the end of the variable

nozzle lance clockwise for narrow spray diffusion and

counterclockwise for wide spray di󰀨usion.

Narrow spray … Water is sprayed in a concentrated direct

ow. The narrow spray setting is useful for

removing stubborn grime.

Wide Spray …… Water is sprayed in a widely diffused

flow. The wide spray setting is useful for

removing dirt from large areas, washing

cars, etc.

Attaching the Foam Nozzle (Fig. 12)

1. Fill the foam nozzle container with manufacturer

recommended detergent.

2. Insert the foam nozzle (9) so that it ts securely into the

slotted mid nozzle lance (3).

3. Insert the foam nozzle completely into the mid nozzle

lance and turn the mid nozzle lance clockwise until it

stops.

4. Test the connection by pulling on the foam nozzle. Keep

hands clear of the nozzle when testing the connection.

Use the foam nozzle in the position shown in Figure 12.

Operating the Unit

1. Ensure that the main switch (12) is in the OFF position.

Plug in the power cord.

2. Turn on the water faucet to the full on position.

3. Release the spray handle safety lock button (13).

4. Water is sprayed from the nozzle when the spray handle

trigger is depressed.

Before turning the main switch to the ON position,

release all accumulated air from inside the hose and

pump by depressing the trigger.

WARNING! Failure to remove the accumulated air from

the hose and pump before turning on the main switch

may result in decreased pressure and/or damage to the

pump and motor.

5. Turn the main switch to the ON position after water

begins to ow smoothly from the nozzle while depressing

the spray handle trigger.

6. Operate the spray by depressing the spray handle

trigger.

The motor stops when the spray handle trigger is

released.

When the trigger is depressed, the motor resumes and

pressurized spray is ejected from the nozzle.

WARNING!

• Maneuver the spray handle hose carefully over rough

surfaces such as gravel, broken concrete, or crushed stone.

• Avoid excessive friction that could damage the spray

handle hose when moving around objects such as

fences, blocks, or bricks.

• Ensure that the spray handle hose is straight and free of

any kinks or twists before using.

• During initial use, the spray stream may be intermittent

and erratic while air is being dispelled from within the

pump and hose. When this occurs, continue to depress

the trigger until the spray stream stabilizes.

• Be sure to turn the main switch to the OFF position

when leaving the unit unattended.

• When spraying, ensure that the spray handle trigger

is always depressed and released for intervals lasting

longer than 2 seconds in duration.

Malfunction of the pressure switch may occur from spray

intervals lasting less than 2 seconds.

After Use

1. Turn the main switch to the OFF position.

2. Turn the water faucet o󰀨.

3. Depress the spray handle trigger until all water has

stopped owing from the nozzle.

4. Pull the hose joint coupler forward to release the water

supply hose from the water connector.

5. Depress the spray handle safety lock button to lock the

trigger.

6. Remove the spray handle hose from the main unit.

7. Remove remaining water from the main unit

Turn the main switch to the ON position for 1-2 seconds

to discharge excess water from the spray handle hose

connection port.

WARNING! Exercise caution as the released of excess

water is highly pressurized

WARNING! Leaving the main switch on for longer than 2

seconds may damage the unit. Be sure to turn the main

switch o󰀨 immediately.

8. Unplug the power cord.

9. Remove the water supply hose from the faucet.

10. Press the release button (18) to remove the spray

handle hose (5) from the spray handle (4). (Fig. 13)

WARNING!

Remove all excess water from the main unit, spray handle

hose, spray handle and nozzles especially in cold weather.

Storing the unit in cold temperatures without removing all

excess water may damage the unit and cause malfunction.

Maintenance and storage

WARNING! Always disconnect the plug form the socket prior

to maintenance or cleaning.

To ensure a long and problem free working life, please take

the following advice:

• Wash o󰀨 water hose, spray handle hose, spray lance and

accessories before mounting.

• Clean the connectors of dust and sand.

Any repair should always be made by our authorized

distributor with genuine spare parts.

Nozzle Cleaning and Maintenance (Fig.14)

• Use the nozzle cleaning pin (8) to regularly clean inside

the nozzle.

• Insert the nozzle cleaning pin (8) into the nozzle and

remove any foreign matter lodged in the nozzle by tapping

the nozzle onto a desk or table with the nozzle opening

pointed downward.

If the nozzle is clogged, low spray pressure and/or

malfunction of the pressure switch may result.

WARNING! Confirm that the nozzle is free of debris by

removing it from the spray handle and visually inspecting

inside the opening. Always clean the nozzle opening after

removing it from the spray handle.

Cleaning the Filter (Fig.15)

1. Loosen the water connector (6) and remove it from the

unit.

2. Remove the lter (16) in the water connector (6).

3. Rinse away any accumulated debris from the filter's

mesh.

4. Return the lter to its original position.

5. Reconnect the water connector to the unit.

Ensure that the water connector is threaded straight

onto the water connection port before gently rotating it

in a clockwise direction. (If the connector is not threaded

correctly onto the port, leaking may occur.)

Cleaning of machine vents

The machine should be kept clean so as to let cooling air

pass freely through air vents.

Storing the Unit

• The hoses, nozzles, and spray handle may be stored on

the main unit as shown in Figure 16.

Storage

Pump, hose and accessories should always be emptied of

water prior to storing as follows:

1. Long periods of nonuse: If the machine is going to be

stored for longer periods of time (i.e. over three months)

in a room where frost could develop, it is recommended

that the machine be filled with an antifreeze solution

(similar to the antifreeze solutions used for vehicles).

2. When the device is not used for an extended period of

time, lime deposits begin to form in the motor pump,

which in turn can lead to starting di󰀩culties.

NEVER START UP A FROZEN MACHINE.

Frost damages are not covered by the guarantee!

Environmental protection

Recycle unwanted materials instead of disposing

of them as waste. All tools, hoses and packaging

should be sorted, taken to the local recycling centre

and disposed of in an environmentally safe way.

WARNING: Do not use appliance without reading

the instruction sheet

Machine not suitable for connection to the potable

water mains

To reduce the risk of injury, user must keep all

bystanders at least 15m away.

High pressure jets can be dangerous if subject to

misuse. The jet must not be directed at persons,

live electrical equipment or the machine itself.

Troubleshooting

Fault Cause Remedy

The machine does not run when the

ON/OFF switch and spray handle lever

are pressed.

The plug is damaged.

There is insu󰀩cient voltage.

The pump is locked.

The thermal relay has triggered.

Check the plug and fuses to see if they

are okay.

Manually turn over the motor.

Let the motor cool down.

The machine runs, however only weak

pressure is generated.

The intake lter is clogged.

Air is being drawn in at the connectors.

The inlet and outlet valves are clogged

or worn.

The diameter of the nozzle hole is too

large.

Clean the lter.

Check the intake connection tting and

the hose connectors.

Clean or replace.

Check and replace.

The operating pressure is irregular.

Air is being drawn in.

The valves are clogged and worn.

The seals are worn.

Check the intake connectors.

Clean and replace.

Check and replace.

The machine suddenly stops. The thermal relay has triggered due to

overheating.

Check the voltage.

Turn off the switch and let the motor

cool down for a few minutes.

Water drop from connect pars. The seals are worn. Check and replace (professional repair

shop)

There is a loss of pressure.

The nozzle is worn.

The valves are dirty or clogged.

The valve seals are worn.

The seals are worn.

The lter is clogged.

Change the nozzle.

Check, clean, exchange.

Check and /or exchange.

Check and /or clean.

There is excess noise.

Air is being drawn in.

The valves are worn, dirty or clogged.

The bearings are worn.

The water temperature is too high.

The lter is dirty.

Check intake lines.

Check, clean, exchange.

Check and /or exchange.

Lower the temperature to below 40℃.

Check and /or exchange.

Expelled water is mixed with oil. The sealing rings (water + oil) are worn. Check and /or exchange.

Water leaks from the pump head. The seals are worn.

The O-ring of the seal set is worn.

Exchange the seal.

Exchange the O-ring.

When the switch is pressed, the motor

hums but does not start.

The mains voltage is lower than that

specied.

The pump is blocked or frozen.

The extension cable is insu󰀩cient (cross

section too small, cable too long)

Check to see that the extension cable

is su󰀩cient.

Exchange the extension cable for one

that is su󰀩cient.

Discarding the machine

Carry out the following safety measures immediately, if you are no longer going to use the machine:

• Pull out the plug and make the machine inoperable.

• Store the machine in an area that cannot be reached by children.

• Do not use any parts from the used machine as replacement parts.

• Disassemble the machine and discard the individual parts in accordance with the regulation neforced in your area.

SAVE THESE INSTRUCTIONS

Hati-hati membaca dan memahami petunjuk ini

sebelum menoperasikan Mesin Cuci Bertekanan

Tinggi.

Isi paket (Gbr 1)

1. Unit utama.

2. Variabel nozzle lance

3. Sambungan Tengah Nozzle

4. Gun

5. Selang (5m)

6. Konektor Air

7. Penyambung Selang

8. Pin pembersih Nozzle

9. Nozzle Sabun

Data Teknis

Daya Input 800 Watt

Rata-rata Tekanan 60bar (6.0 Mpa)

Maksimal Tekanan 90bar (9.0 Mpa)

Rata-rata Air Mengalir 4.8 L/Menit

Tekanan air masuk Maks. 1.0 Mpa

Maksimal Temperatur Air 40ºC

Menambahkan Air Dari Keran

Berat 3.8kg

Level Tekanan Suara

Uncertainty

LpA=76dB(A)

KPA=3dB

Level Kekuatan Suara LwA=92dB(A)

Nilai getaran aH=1.8m/s2

Kah=1.5m/s2

Nama Bagian

1. Unit utama.

2. Variabel nozzle lance

3. Sambungan Tengah Nozzle

4. Gun

5. Selang (5m)

6. Konektor Air

7. Penyambung Selang

8. Pin pembersih Nozzle

9. Nozzle Sabun

10. Selang Air

11. Klem Selang

12. Saklar

13. Pengaman Kunci Tombol

14. Pelatuk

15. Kabel Daya

16. Filter

17. Inlet Air

18. Tombol Melepaskan Selang

Persiapan

Sebelum memulai mesin Anda, kami menyarankan Anda

untuk hati-hati

Baca petunjuk ini. Ikuti semua petunjuk untuk meminimalkan

risiko cedera ketika menggunakan mesin.

Sebelum operasi

Sebelum memulai mesin Anda, silahkan cek dengan hati-

hati untuk setiap cacat. Jika Anda menemukan apapun,

Jangan mulai mesin Anda dan

Hubungi distributor Anda.

Pemeriksaan Utama :

Isolasi kabel listrik harus sempurna dan tanpa ada yang

retak. Jika kabel listrik rusak, itu harus digantikan oleh pusat

layanan resmi kami.

Sambungan Listrik

Berikut yang harus diperhatikan saat menghubungkan

mesin ke instalasi listrik:

• Memeriksa daya sebelum mengoperasikan agar sasuai

dengan spesikasi yang tertera pada label.

• Mesin ini dilengkapi dengan motor universal dengan

insulasi ganda. Hal ini tidak perlu menggunakan koneksi

bumi (Ground).

• Instalasi listrik sudah bersetikat.

• Sangat dianjurkan bahwa listrik mesin harus sudah

mencakup dengan perangkat saat ini(RCD).

• Level Keamanan Produk : IPX5

Peraturan Keselamatan Umum dan

Pencegahan Kecelakaan

Ini Penting bahwa Anda membaca peraturan keselamatan

dan instruksi pengoperasian secara keseluruhan dan

mengikuti informasi yang terkandung di dalamnya untuk

menghilangkan kemungkinan kecelakaan atau berpotensi

situasi berbahaya yang terjadi saat bekerja dengan mesin.

• Konektor daya harus dipasang ke soket diinstal dengan

benar. Kekuatan daya untuk perangkat saat ini max. 30

mA.

• Selalu periksa perangkat, kabel listrik dan steker sebelum

menggunakan mesin. Gunakan alat ini hanya dalam

keadaan dan tidak rusak dengan cara apapun. Bagian-

bagian yang rusak harus segera diganti oleh teknisi

distributor.

• Selalu menarik konektor daya dari stopkontak soket

sebelum melakukan pekerjaan pada mesin, sebelum

mengubah nosel dan setiap kali mesin tidak sedang

digunakan.

• Peringatan! Perpanjangan kabel yang tidak

direkomendasikan dapat berbahaya.

• Jika kabel digunakan, itu akan cocok untuk penggunaan

outdoor dan koneksi harus selalu disimpan tempat yang

kering.

• Hanya menggunakan kabel Sambungan yang cocok

ketika bekerja di luar ruangan. Kabel Sambungan harus

memiliki minimal berukuran 1,5 mm2.

• Peringatan! Perangkat ini dikembangkan untuk

digunakan dengan pembersihan bentuk yang disediakan

atau direkomendasikan oleh produsen. Penggunaan

lain pembersihan bentuk atau bahan kimia negatif dapat

mempengaruhi keamanan perangkat.

• Kabel sambungan harus disimpan kering dan dari tanah.

Selalu luruskan kabel sambungan yang benar-benar lurus

untuk menghindari kerusakan panas kabel akibat terlilit.

• Peringatan! Jangan gunakan perangkat ketika orang atau

hewan lain di sekitarnya kecuali mereka mengenakan

pakaian pelindung yang sesuai.

• Peringatan! Mesin dapat berbahaya ketika mesin tidak

digunakan dengan benar. Jangan hadapkan langsung

mesin terhadap orang, hewan, peralatan listrik hidup atau

perangkat itu sendiri.

• Jangan hadapkan langsung mesin terhadap diri sendiri

atau orang lain untuk membersihkan pakaian dan alas

kaki.

• Anak-anak harus diawasi untuk memastikan bahwa

mereka tidak bermain dengan mesin.

• Mesin ini tidak dimaksudkan untuk digunakan oleh

orang-orang (termasuk anak-anak) dengan keterbatasan

fisik, indera atau kecakapan mental, atau kurangnya

pengalaman dan pengetahuan, "High pressure cleaners

akan tidak dapat digunakan oleh anak-anak atau terlatih

personil."

• Peringatan! Selang Mesin, tting dan kopling merupakan

komponen penting untuk keselamatan perangkat. Hanya

menggunakan Selang Mesin, fitting dan kopling yang

direkomendasikan oleh produsen.

• Untuk memastikan keamanan operasional perangkat,

hanya menggunakan suku cadang asli produsen atau

bagian yang telah disetujui oleh produsen.

• Tidak beroperasi perangkat jika kabel listrik atau bagian

penting lain dari perangkat-misalnya keamanan terkait

elemen, semprot menangani selang, pistol semprot-

rusak.

• Tidak menarik atau membawa alat listrik oleh kabel listrik

nya. Melindungi kabel listrik dari kerusakan oleh logam,

pelarut yang tajam.

• Menjaga tempat kerja rapi.

• Memastikan bahwa saklar dimatikan saat

menghubungkan mesin.

• Mengenakan pakaian cocok saat bekerja.

• Periksa mesin Anda untuk memastikan bahwa itu adalah

dalam rangka kerja yang baik. Jika tidak berfungsi

dengan baik, segear diperiksa oleh pusat layanan resmi

kami. Memiliki semua pemeliharaan dan inspeksi bekerja

dilakukan hanya oleh pusat layanan resmi kami.

• Air jet yang muncul dari nozzle tekanan tinggi

menghasilkan 'kickback' pada pegangan semprot. Oleh

karena itu, pastikan bahwa Anda memiliki pijakan yang

kuat dan bahwa Anda memiliki memegang teguh dari

cengkeraman pegangan. Untuk melindungi diri dari

mungkin terbangnya objek (yang dirilis berkat tekanan

tinggi).

• Tinggi tekanan jet dapat merusak badan kendaraan dan

bagian kendaraan lainnya. Menjaga jarak minimal 30 cm

dari objek yang dibersihkan.

• Jika terjadi kegagalan daya ketika Anda menggunakan

mesin, pastikan untuk mematikan mesin untuk alasan

keamanan.

• Komponen Pompa listrik harus selalu dapat pasokan air

yang cukup. Komponen Pompayang kering menyebabkan

kerusakan parah pada komponen Pompa.

• Lepaskan dari catu daya sebelum melaksanakan

pemeliharaan Perangkat.

• Jika kabel rusak, itu harus diganti oleh pusat layanan

resmi kami untuk menghindari bahaya.

• Jangan menggunakan mesin dalam lingkungan dimana

dapat menjadi bahaya ledakan. Jika timbul keraguan,

silakan hubungi pusat layanan resmi kami.

• Hal ini tidak diperbolehkan untuk membersihkan

permukaan yang mengandung asbes dengan tekanan

tinggi.

• Mesin ini tidak boleh digunakan pada suhu dibawah 0ºC

• Sambungan pasokan listrik (misalnya, koneksi kabel

RCD atau memperbaiki) dilakukan dengan kualikasi dan

mematuhi IEC60364-1: instalasi listrik tegangan rendah.

Keamanan Perangkat

Keamanan Kunci pada Penyemprot

Pada penyemprotan terdapat tur keamanan kunci tombol

(13). Apabila kunci diaktifkan, pegangan semprot tidak dapat

dioperasikan.

Perlindungan Motor Pompa

Motor dilengkapi dengan saklar motor circuit breaker. Ketika

motor mulai menjalankan panas, adalah akan mati secara

otomatis yang diputus oleh switch ini. Mematikan mesin.

Menunggu 5 ~ 10 menit sebelum menggunakan perangkat

lagi. Cobalah untuk menentukan penyebab kesalahan. Jika

masalah berulang dengan sendirinya, silakan hubungi pusat

layanan resmi kami.

Instruksi operasi

Tujuan

Mesin dirancang untuk membersihkan kendaraan, mesin,

bangunan, fasad, dll di sektor swasta.

Area Kerja

• Jangan pernah menggunakan mesin di daerah-daerah

yang berpotensi meledak dalam keadaan apapun!

• Temperatur operasi harus antara 0ºC dan + 40ºC.

• Mesin terdiri dari Komponen dengan pompa, yang

terbungkus busa sebagai peredam. Untuk posisi kerja

yang optimal mesin dilengkapi dengan karet pada tombak

dan pegangan non slip, bentuk dan konfigurasi yang

sesuai dengan persyaratan yang berlaku.

• Jangan menutup atau memodifikasi Nosel atau spray

Nozzle dengan cara apapun.

• Mesin ini dirancang untuk digunakan dengan suhu dingin

atau hangat (maks 40ºC); suhu yang lebih tinggi dapat

merusak pompa.

• Jangan menggunakan air yang kotor, berpasir atau

berisi produk kimia, hal ini bisa mengganggu operasi dan

mempersingkat masa pakai mesin.

Perakitan

*alat yang diperlukan untuk perakitan: pasokan air selang,

Klem selang, obeng Phillips

*selang air harus memiliki diameter dalam setidaknya

13mm (1/2 in.) dan harus diperkuat. Pasokan air harus

sama dengan kapasitas penyampaian mesin.

1. Menyambung lance nosel semprot. (Gbr.2)

Sambungkan dengan lance nozzle (2 dan 3) dengan

sambungkan Semprotan (4) dan putar sampai dua

bagian benar-benar terkunci. Tes sambungan dengan

cara menarik nozzle.

2. Hubungkan selang semprot (5) untuk menangani

semprot (4). (Gambar.3)

Peringatan! Kebocoran air dapat terjadi jika selang tidak

diamankan dengan baik atau jika konektor tidak bebas

dari kotoran dan puing-puing sebelum menghubungkan.

3. Menghubungkan selang spray nozzle masuk air (Fig.4:

perubahan) Menghubungkan semprot selang (5)

langsung ke nozzle masuk air dan memutar baut selang

searah jarum jam untuk terhubung. Mengubah baut

selang sampai kencang.

PERINGATAN! Baut sealng kuarng kencang, dapat

menyebabkan air bocor dari daerah koneksi.

4. Pasang dan putar konektor air (6) ke dalam pipa

pemasukan air (17). (Gambar 5)

Inhaltsverzeichnis

Sprachen:

Andere Kyocera Hochdruckreiniger Handbücher

Kyocera

Kyocera AJP-1100 Bedienungsanleitung

Beliebte Hochdruckreiniger Handbücher anderer Marken

Shark

Shark RG-232637 Bedienungsanleitung

Shakti Technology

Shakti Technology S3 Bedienungsanleitung

Kärcher

Kärcher K 4 Pure Bedienungsanleitung

Porter-Cable

Porter-Cable D25806-025-2 Bedienungsanleitung

REM POWER

REM POWER HDEm 662 Bedienungsanleitung

Landa

Landa HS-3000 Bedienungsanleitung

Craftsman

Craftsman 580.752270 Bedienungsanleitung

HIKOKI

HIKOKI AW 100 Bedienungsanleitung

Delco

Delco DC 1302 Bedienungsanleitung

Kärcher

Kärcher K 3 Full Control Bedienungsanleitung

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Bedienungsanleitung

ARKSEN

ARKSEN 014-HG-14141-HR Bedienungsanleitung

Black & Decker

Black & Decker PW1700SPX Bedienungsanleitung

Kärcher

Kärcher 595 - SPARE Leitfaden

Kranzle

Kranzle B 10 200 Bedienungsanleitung

Stihl

Stihl RE 90 Bedienungsanleitung

PowR-Quip

PowR-Quip PQ-2600 Bedienungsanleitung

Hotsy

Hotsy 5645 Bedienungsanleitung