Kyocera Ecosys FS-3820N Bedienungsanleitung

Installation Guide

FS-3820N

FS-3830N

Page Printers

FS3830NIG.book 1 ページ２００３年１２月１２日　金曜日　午前１０時０分

Caution

No liability is assumed for any damage caused by improper installation.

Notice on Software

Software used with this printer must support the printer’s emulation mode. The printer is factory-set to emulate

the HP PCL 6. The emulation mode can be changed by following the procedures described in the Operation

Guide contained as an electronic file in the CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be inserted in

future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present

edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No

responsibility is assumed for defects in the printer’s firmware (contents of its read-only memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page

printer, are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this

manual, any copyrightable subject matter without the prior written consent of Kyocera Mita Corporation is pro-

hibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copy-

right notice as the material from which the copying is done.

Table of Contents

STEP 1 Unpacking ......................................................................... 1

STEP 2 Positioning the Printer ..................................................... 2

STEP 3 Installing the Toner Container ......................................... 3

STEP 4 Installing the Waste Toner Box........................................ 5

STEP 5 Connecting the Printer to the Computer ........................ 7

STEP 6 Connecting the Power Cord ............................................ 9

STEP 7 Adding Paper to the Paper Cassette and MP Tray....... 10

STEP 8 Turning the Power Switch On ........................................ 18

STEP 9 Printing a Status Page.................................................... 19

Revision 1.1 January 2004

FS3830NIGTOC.fm 1 ページ２００４年１月１４日　水曜日　午後１時４０分

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is miss-

ing against the list of shipped components below.

List of Shipped Components

STEP

Printer

(E)

(D)

(A)

(B)

(F)

(C)

(for

U.S.A.

only)

Printer

Power Cord (F)

Installation Guide

[this booklet] and

other printed matter

(B)

CD-ROMs (B)

Waste Toner

Box (E)

To n e r

Container (D) Plastic Bag for

Developer Unit (A)

Dust Cover (C)

[for U.S.A. only]

FS3830NIG.book 1 ページ２００３年１２月１２日　金曜日　午前１０時０分

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Be sure to secure enough space

around the printer. Prolonged

usewithoutsufficientclearance

may cause heat to build up

within the printer, resulting in

fire.

Environment

Do not install the printer where temperature or humidity is outside the rec-

ommended range. Print quality may suffer and there will be an increased

chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

• Excessive dust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or

make liberal use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above

sea level

Te m p e r a t u r e 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

STEP

30 cm (11-13/16 inches)

25 cm

(9-7/8

inches)

60 cm

(23-5/8

inches)

30 cm

(11-13/16

inches)

20 cm (7-7/8 inches)

[40 cm (15-3/4 inches) when the option

rear tray is installed]

FS3830NIG.book 2 ページ２００３年１２月１２日　金曜日　午前１０時０分

Installing the Toner Container

Before you can use the printer for the first time, you must prepare it by installing the

toner container, waste toner box, and set up the interfacing with the computer.

1Open the printer top cover all the way.

2Take the toner container from the bag.

3With the label side down, thoroughly

shake the toner container (in the direc-

tion of the arrow) ten times or more to

loosen and mix the toner inside.

4Carefully remove the protective seal.

5Install the toner container into the

printer.

STEP

Top Cover

Toner Container

10 times or

Protective Seal

FS3830NIG.book 3 ページ２００３年１２月１２日　金曜日　午前１０時０分

6Push firmly on the top of the toner con-

tainer at the positions marked PUSH

HERE.

When the toner container fits into place,

it will lock with a clicking sound.

7Close the top cover.

To remove the toner container

Pull the lock lever (blue colored) to the

right and gently lift the toner con-

tainer.

Lock Lever

FS3830NIG1.fm 4 ページ２００４年１月１４日　水曜日　午後１時４１分

Installing the Waste Toner Box

The waste toner box is supplied with the printer. The waste toner box must be installed

in the printer.

1Open the cap of the waste toner box.

2Open the left cover on the left side of the

printer.

3Insert the waste toner box as shown in

the figure. The box will be locked when

it fits into place.

STEP

Cap

Waste Toner

Box

Left Cover

FS3830NIG.book 5 ページ２００３年１２月１２日　金曜日　午前１０時０分

4Ensuring that it is correctly inserted,

close the left cover.

To remove the Waste Toner Box

While holding the waste toner box,

press the lock lever and then gently

remove the waste toner box.

Lock Lever

FS3830NIG.book 6 ページ２００３年１２月１２日　金曜日　午前１０時０分

Connecting the Printer to the Computer

There are various ways of connecting the printer to the computer, such as through the

parallel interface connector, through the USB (Universal Serial Bus) interface connec-

tor, and through the network interface connector. In addition, a serial interface and a

second network interface are optionally available as well.

Printer Connections

Before performing this step, be sure to turn off both the printer and the com-

puter’s power switches and unplug the printer’s power plug from the power

outlet. Failure to do so may result in electrical shock.

The standard Centronics parallel interface connector ( ), USB interface connec-

tor ( ) and network interface connector ( ) are located on the rear of the

printer.

STEP

Printer (Rear)

Power Supply

Option Serial Interface

Board Kit (3.3 V DC)

Serial Interface

Parallel Interface

USB Interface

Network Interface

Connector for option sorter

(See the option sorter’s

user’s manual.)

Network

Option Network Interface Card

(3.3 V DC)

FS3830NIG.book 7 ページ２００３年１２月１２日　金曜日　午前１０時０分

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nector on the rear of the printer.

• Use a parallel printer cable

that complies with the

IEEE1284 standards.

• The printer will work best if it

is installed near the com-

puter. The connecting cable

should be shielded and not be

longer than 3 meters (10 feet).

2Close the clips on both sides to fix the

connector in place.

Plug the other end of the printer cable

into the computer’s parallel interface

connector.

USB (Universal Serial Bus) Interface Connection

1Plug one end of the USB cable into the

USB interface connector on the rear of

the printer.

• Use a cable that complies

with Revision 2.0 of USB stan-

dard. (a rectangular Type A

plug or a square Type B plug).

• The connecting cable should

be shielded and not be longer

than 5 meters (16 feet).

2Plug the other end of the USB cable into

the computer’s USB interface connec-

tor.

Network Interface Connection

1Plug one end of the network cable (not

included) into the network interface

connector on the rear of the printer.

Use an Ethernet cable (10Base-

T or 100Base-TX) as the net-

work cable.

2Plug the other end of the network cable

into the network hub.

ParallelPrinter

Cable

Clip Clip

USB Cable

Network Cable

FS3830NIG.book 8 ページ２００３年１２月１２日　金曜日　午前１０時０分

Andere Handbücher für Ecosys FS-3820N

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kyocera Drucker Handbücher

Kyocera

Kyocera FS-600 Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C5150DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS P4140dn Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C5350DN Bedienungsanleitung

Kyocera

Kyocera PA2001w Bedienungsanleitung

Kyocera

Kyocera ECOSYS P6235cdn Bedienungsanleitung

Kyocera

Kyocera FS-1040 Bedienungsanleitung

Kyocera

Kyocera KM-3035 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3051ci Bedienungsanleitung

Kyocera

Kyocera 4004i Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-3140MFP Bedienungsanleitung

Kyocera

Kyocera DP-3600 Handbuch

Kyocera

Kyocera TASKalfa 2320 Bedienungsanleitung

Kyocera

Kyocera FS FS-1920 Bedienungsanleitung

Kyocera

Kyocera FS-2000DN Bedienungsanleitung

Kyocera

Kyocera Ai3010 Bedienungsanleitung

Kyocera

Kyocera Ecosys FS-3820N Bedienungsanleitung

Kyocera

Kyocera ECOSYS P2135dn Bedienungsanleitung

Kyocera

Kyocera EcoLAN 3000E Bedienungsanleitung

Kyocera

Kyocera ECOSYS P4035dn Bedienungsanleitung

Kyocera

Kyocera TASKalfa 306cl Bedienungsanleitung

Kyocera

Kyocera Ci1000 Bedienungsanleitung

Kyocera

Kyocera FS-1020MFP Bedienungsanleitung

Kyocera

Kyocera FS-8000C Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Lexmark

Lexmark Infoprint 1332 Bedienungsanleitung