La Crosse Technology Wireless Temperature Station WS-7013TWC Bedienungsanleitung

Quick Start for your WS-7013U

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor station and outdoor remote 3 to 5 apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the outdoor remote first then into the indoor station.

(All outdoor remotes must be started before the indoor station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the display and sensor will start to talk to each other and the display will show both the indoor

temperature and an outdoor temperature. If the station does not display both temperatures after the 10

minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed

for 10 minutes you can place your sensor outdoors and set your time.

The remote sensor should be placed in a dry, shaded area. The remote sensor has a range of 80 feet. Any

walls that the signal will have to pass through will reduce distance. An outdoor wall or window will have

20 to 30 feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your distance plus

resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote sensor but direct rain must be avoided.

To complete the set up of your temperature station after the 10 minutes have passed please follow the steps

below.

1. Press and hold the SET button for 5 seconds.

A 12h or 24h will appear on the top line. (12h for AM/PM, 24h for military time)

a. To change between 12h and 24h press and release the MIN/MAX button.

When you have your choice shown on the display press and release the SET button

once.

2. Degree Fahrenheit will now show.

a. To change between Fahrenheit and Celsius, press and release the MIN/MAX button.

When you have your choice shown on the display press and release the SET button

once.

3. An hour will now be flashing.

a. Press and release the MIN/MAX button until the correct hour is shown.

NOTE: When in the 12h mode there is “PM” displayed under the word TIME when in the PM

hours. During the AM hours this area will be blank.

When the correct hour is shown press and release the SET button once.

4. A minute will now be flashing.

a. Press and release the MIN/MAX button until the correct minutes are displayed.

Press and release the SET button once more and you are done.

7,0(

WS-7013U

Wireless 433 MHz

Temperature Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents 1

Quick Setup 2

Detailed Setup Guide

Battery Installation 3-4

Setting the Time 5

Selecting Units of

Measurement 6

Features

Minimum and Maximum

Temperatures 6-7

Resetting Minimum and

Maximum Temperatures 7

Additional remote control

senders (optional) 7-10

Mounting 10-11

Troubleshooting 12-14

Maintenance and Care 14-15

Specifications 15-16

Warranty Information 17-19

INVENTORY OF CONTENTS

1. The Indoor Temperature Station (Figure

2. The Remote Control Sensor (TX2U)

and mounting bracket. (Figure 2)

3. 3 each, 1/2” Philips screws.

4. One strip of double sided adhesive tape.

5. Instruction Manual and Warranty Card.

ADDITIONAL EQUIPMENT

(not included)

1. 1 Philips screwdriver.

2. 2 Fresh AAA 1.5V batteries.

3. 2 Fresh AAA 1.5V batteries.

Figure 2

7,0(

ure 1

QUICK SETUP

1. Insert two AAA batteries into the

Remote Control Sender.

2. Insert two AAA batteries into the

Indoor Temperature Station.

3. Wait 5-6 minutes, or until the outdoor

temperature is displayed in the

OUTDOOR LCD of the Temperature

Station.

4. Set the Time

5. Mount units.

(See complete instructions for details).

Note: The Remote Control Sender transmits

a signal every 3 minutes. After the batteries

have been installed, the Indoor Temperature

Station searches for these signals for a

duration of 6 minutes. If there is no

temperature reading in the OUTDOOR LCD

after 6 minutes, make sure the units are

within range of each other, or repeat battery

installation process.

DETAILED SETUP GUIDE

I. BATTERY INSTALLATION

A. REMOTE CONTROL SENDER

1. Remove the mounting bracket.

2. Remove battery cover

3. Observing the correct polarity, install

2 AAA batteries—make sure they do

not spring free, or start-up problems

may occur. Replace cover.

B. TEMPERATURE STATION

Note: After the batteries are installed, DO

NOT press any buttons. This may interfere

with the signals, causing temperatures to

Battery cover

Battery compartment

7,0(

1. Remove the battery cover on the

backside. To do this, push up and pull

out.

2. Observing

the correct

polarity,

install 2 AA

batteries.

3. Replace

battery

cover.

4. Wait 5-6 minutes or until both indoor

and outdoor temperatures are shown

on the Indoor Temperature Station.

5. The Temperature

Station should now

show: “-:- -” in the

TIME LCD, and

temperatures in the

INDOOR and

OUTDOOR

LCD’s.

Battery

Cover

II. TIME

A. SETTING THE TIME

1. Press and

hold the SET

button for 1

second. “12h”

will appear in the TIME LCD.

2. Use the MIN/MAX button to select

either 12h time (am/pm) or 24h time

3. Press the SET button 2 times, the hour

will flash in the upper left corner.

4. Press the MIN/MAX button to set the

hours, press the SET button, and press

the MIN/MAX button to set the

minutes.

5. Press the SET button to activate the

clock.

Note: When in 12h mode, there is only a

“PM” display, which appears under “TIME.”

If there is no display here it is AM. Make

sure you set the time accordingly.

III. UNITS OF TEMPERATURE

MEASURE

A. SELECTING UNITS OF

MEASUREMENT

1. Press and hold the SET button for 1

second.

2. Press the SET button again. “°F” will

appear in the TIME LCD.

3. Press the MIN/MAX button to shift

between °F and °C.

4. Press the SET button twice to activate

settings.

IV. FEATURES

A. MINIMUM AND MAXIMUM

TEMPERATURES

1. Press the MIN/MAX button. “MIN”

appears in the temperature LCD’s and

the recorded minimum temperatures

are displayed.

2. Press the MIN/MAX button to toggle

to the maximum temperatures. The

time of occurrence of the value for

outdoor temperature will also flash.

B. RESETTING THE MINIMUM AND

MAXIMUM TEMPERATURES

1. To reset both the minimum and

maximum temperatures—press and

hold the RESET/+ button for 4

seconds.

C. ADDING ADDITIONAL

REMOTE CONTROL SENDERS

(OPTIONAL)

1. The WS-7013U is able to receive

signals from 3 different Remote

Control Senders. Following are some

brief instructions for the basic set-up

of Remote Control Sender units with

the WS-7013U. These extra sensors

can be purchased through the same

dealer as this unit, or by contacting

La Crosse Technology directly. A

TX2U will monitor temperature only,

a TX3U will monitor temperature and

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology C85845 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8158U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 327-1417BW Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1414Bv3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7076U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415C Bedienungsanleitung

La Crosse Technology

La Crosse Technology V50 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V61 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1912 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-2316 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9060U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1516-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2801-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9035U Bedienungsanleitung

La Crosse Technology

La Crosse Technology V50EU Installationsanleitung

La Crosse Technology

La Crosse Technology S88907V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V15-AU Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8120U-IT Installationsanleitung

La Crosse Technology

La Crosse Technology WS-1613-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1517U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9006U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1451 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9117U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology C85845v4 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung