La Crosse Technology WS-9006U Bedienungsanleitung

WS-9006U

Wireless Temperature Station

Instruction Manual

FEATURES:

Four digit time display

12-hour or 24-hour selectable time

Indoor temperature (°F or °C)

Outdoor temperature (°F or °C)

Minimum and Maximum temperature

Four level RF strength indicator

Wall hanging or free standing

Low battery indicator for receiver and transmitter

100 foot wireless transmission range (open air)

RF reception

indicator

Indoor

Temperature

Outdoor

Temperature

Time

MIN/MAX/+ Button

CF / SET Button

Outdoor

Temperature

Sensor TX43U

INITIAL SET UP:

IMPORTANT:- Do Not Mix Old and New Batteries

- Do Not Mix Alkaline, Standard, or Rechargeable Batteries

NOTE: This temperature station can receive one transmitter only.

First, insert fresh 2x AA, IEC LR6, 1.5V alkaline batteries into the TX43U transmitter, observing the

correct polarity (see marking inside battery compartment). Keep transmitter 5-10 feet from the

temperature station.

Within 30 seconds of powering up the transmitter, insert 2x AAA, IEC LR3, 1.5V batteries into the

Temperature Station, observing the correct polarity (see marking inside battery compartment). Once

the batteries are in place, all segments of the LCD will light up briefly. Following, the indoor

temperature will display. If the indoor temperature does not show in the LCD after 60 seconds,

remove the batteries and wait for at least 60 seconds before reinserting them. Once the indoor data is

displayed, proceed to the next step.

After the batteries are inserted, the Temperature Station will start receiving outdoor temp data from

the transmitter. The outdoor temperature should be displayed on the Temperature station. If this does

not happen after 2 minutes, remove the batteries from both units and start again from the beginning.

In order to ensure sufficient 433 MHz transmission, place the outdoor transmitter a distance of no

more than 100 feet (30 meters) from the Temperature Station and the transmitter.

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER

The Temperature transmitter uses 2 x AA, IEC LR6, 1.5V batteries. When batteries will

need to be replaced, the low battery icon will appear on the LCD in front of the outdoor

temperature. To install and replace the batteries, please follow the steps below:

1. Remove the battery compartment cover. (Slide to the bottom and then lift straight off).

2. Insert the batteries, observing the correct polarity (see marking).

3. Replace the battery cover to the unit.

NOTE: When changing batteries in any of the units, all units need to be reset by

following the set up procedures. The transmitter at start-up, assigns a random security

code and this code must be received and stored by the Temperature Station in the first

few minutes of power supplied.

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION

The Temperature Station uses 2 x AAA, IEC LR3 1.5V batteries. When batteries

need to be replaced, the low battery icon will appear in front of the indoor

temperature.

To install and replace the batteries, please follow the steps below:

1. Remove the battery compartment cover.

2. Insert batteries observing the correct polarity (see marking).

3. Replace battery compartment cover.

LOW BATTERY:

Replace the batteries in all units every 12 months to ensure optimum accuracy of these units. A low

battery icon will display next to the outdoor temperature when the transmitter batteries are low and next to

the indoor temperature then the batteries in the temperature station are low.

SET TIME:

12/24-HOUR TIME: Hold the CF/SET button until 12hr or 24hr flashes in the lower

right hand corner. Press and release the MIX/MAX/+ button to switch between 12-hour

and 24-hour time. Press the CF/SET button once to continue.

HOUR: The Hour will flash. Press and release the MIX/MAX/+ button to change the

hour. Press the CF/SET button once to continue.

MINUTES: The minutes will flash. Press and release the MIX/MAX/+ button to change

the minutes.

NOTE: Hold the MIX/MAX/+ button to move quickly through the numbers. Press

CF/SET once to confirm and exit.

TEMPERATURE SELECTION:

FAHRENHEIT/CELSIUS: Press and release the CF/SET button once to switch from Fahrenheit to

Celsius.

FOUR LEVEL RF INDICATORS: The temperature station will indicate strength of signal

reception from the outdoor transmitter by the number of bars on the RF indicator icon.

4-bars: Shows after initial set up and stays when reception is at full strength.

3-bars: Indicates one reception failure from the outdoor transmitter.

2-bars: Indicates two reception failures from the outdoor transmitter.

1-bar: Indicates three reception failures from the outdoor transmitter.

0-bars: Indicates four reception failures from the outdoor transmitter.

The antenna symbol will flash on initial set while searching for the signal. If it fails to receive a signal after

63 minutes the temperature station will display dashes (“--.-“). The temperature station will search again

for a signal for 3 minutes every next hour.

MIN/MAX RECORDING:

VIEW MIN/MAX: Press the MIN/MAX/+ button view indoor and outdoor MAX, MIN and Current

temperature.

RESET MIN/MAX: Hold the MIN/MAX/+ button for 3 seconds to reset all MIN/MAX readings to current

temperatures.

OUTDOOR TRANSMITTER RESET BUTTON:

The Temperature Transmitter has a RESET button. Use a small pointed object to gently press and

release to send a signal. Follow the instructions for in SET UP regarding the display.

NOTE: Removing power from the transmitter and display negates the need for the RESET button.

POSITIONING THE TEMPERATURE STATION:

Stand the Temperature Station on a tabletop, counter or desk, or mount on a wall. Ensure that the

Temperature Station continuously receives the 433MHz signal from the Sensor before mounting it in the

desired location.

WALL MOUNT

Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an

inch (5mm) extended from the wall.

Place the Temperature Station onto the screw, using the hanging hole on the

backside. Gently pull the Temperature Station down to lock into place.

NOTE: Always ensure that the Temperature Station locks onto the screw before

releasing the station.

TABLE STAND: The Temperature Station has a wide base to stand on a desk or table.

POSITIONING THE REMOTE TEMPERATURE TRANSMITTER:

Wall mount using the hole on the back of the sensor. Best location is under the eave (12-18 inches) on

the North side of the home.

WALL MOUNT:

1. Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an

inch (5mm) extended from the wall.

2. Place the temperature transmitter onto the screw, using the hanging hole on the

backside. Gently pull the transmitter down to lock into place

NOTE: Always ensure that the transmitter locks onto the screw before releasing.

TABLE STAND: Not recommended as the transmitter may be blown over and

damaged.

NOTE:The mounting surface can affect the transmission range. If, for instance, the transmitter is

attached to a piece of metal, it may reduce the transmitting range. For this reason, we recommend not to

place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in

the immediate vicinity (garage doors, double-glazing, etc.). Before securing in place, please ensure that

the Temperature Station can receive the 433MHz signal from the temperature transmitter at the positions

that you wish to place them.

Place the remote temperature transmitter outside in a dry, shaded area. The remote temperature

transmitter has a range of 100 feet (30 meters). Keep in mind this distance is in open air with no

obstructions and that radio waves DO NOT curve to go around objects. Real-world transmission range

will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings,

thick trees, etc.) will effectively cut signal range in half.

MAINTENANCE:

Keep the temperature station in a dry place.

Do not expose the display to extreme temperatures, vibration or shock.

Clean it with a soft damp cloth. Do not use solvents or scouring agents.

If the unit does not work properly, change the battery.

Do Not Mix Old and New Batteries

Do Not Mix Alkaline, Standard, or Rechargeable Batteries

SPECIFICATIONS:

Indoor Temperature:

Range: 32° F to 122° F (0° C to 50° C)

Resolution: 1° F/C

Interval: 57 seconds

Outdoor Temperature:

Range: -22° F to 140° F (-30° C to -60° C)

Resolution: 1° F/C

Interval: 57 seconds

Power:

Receiver: 2-AAA, IEC, LR3 alkaline batteries.

Transmitter: 2-AA, IEC, LR6 alkaline batteries.

Dimensions:

Receiver: 2 ½” W x 1” D x 3 ¾” H

Transmitter: 1 ¾” W x 1” D x 4” H

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing

defects in materials and workmanship.

This limited warranty begins on the original date of purchase, is valid only on products purchased and

used in North America and only to the original purchaser of this product. To receive warranty service, the

purchaser must contact La Crosse Technology, Ltd for problem determination and service

procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service

center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse

Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.

La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated

herein, with new or reconditioned parts or products if found to be defective during the limited warranty

period specified above. All replaced parts and products become the property of La Crosse Technology,

Ltd and must be returned to La Crosse Technology, Ltd.

Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever

is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered

by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which

is not in need or repair, you will be charged for the repairs or examination.

The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to

a La Crosse Technology, Ltd authorized service center.

Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the

following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including

the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must

be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4)

damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage

resulting from the performance of repairs or alterations by someone other than an authorized La Crosse

Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and

uses that this product was not intended or (8) the products inability to receive a signal due to any source

of interference.

This warranty covers only actual defects within the product itself, and does not cover the cost of

installation or removal from a fixed installation, normal set-up or adjustments, claims based on

misrepresentation by the seller or performance variations resulting from installation-related

circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL,

CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE

OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR

MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT

OF CHILDREN’S REACH.

This warranty gives you specific legal rights. You may also have other rights specific to your

State. Some States do no allow the exclusion of consequential or incidental damages therefore the

above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology

2817 Losey Blvd. S.

La Crosse, WI 54601

The complete instruction manual is available at:

www.lacrossetechnology.com/9006

Le manuel d'instruction complet est disponible sur:

www.lacrossetechnology.com/9006

El manual de instrucciones completo está disponible en:

www.lacrossetechnology.com/9006

Contact Support: 1-608-782-1610

Product Registration: www.lacrossetechnology.com/support/register.php

FCC ID: OMO-M-13 (transmitter)

FCC DISCLAIMER

Statement according to FCC part 15.19:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Statement according to FCC part 15.21:

Modifications not expressly approved by this company could void the user's authority to operate the

equipment.

Statement according to FCC part 15.105:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

processed using electronic, mechanical or chemical procedures without written permission of the

publisher.

This handbook may contain mistakes and printing errors. The information in this handbook is regularly

checked and corrections made in the next issue. We accept no liability for technical mistakes or printing

errors, or their consequences.

All trademarks and patents are acknowledged.

EJMA9006L210#

Printed in China

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-7091UD Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9021U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6818 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8120U-IT Installationsanleitung

La Crosse Technology

La Crosse Technology Professional Remote Weather Station Kurzanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9620U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7075UF Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6862 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6835 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8035U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7049-Mah Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417BL Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1409 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-1913U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2801-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology S88907V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1414MBv2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology CA76669 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1414M Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2317 Technisches Datenblatt

La Crosse Technology

La Crosse Technology 327-1417 Abmessungen

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung