La Crosse Technology WS-1913IT Technisches Datenblatt

Cable connection between the wind sensor and

the thermo-hygro transmitter

OPTIONAL

Wireless

transmission–Self-

Emptying Rain sensor

to weather centre

Wireless transmission -

Thermo-hygro transmitter

to weather centre

Weather Centre

Wind Sensor

Rain Sensor (sold separately)

Thermo-hygro

Transmitter

QUICK SET UP MANUAL –

PROFESSIONAL WEATHER CENTRE

INITIAL SETUP:

Note: When putting the Weather Centre into operation,

it is important to have them in close proximity (e.g. on a

table) while completing wiring and set-up of the system.

This step is important to allow testing of all components

for correct function before placing and mounting them at

their final destinations (See Positioning below).

1. Unwind the cables of the Wind sensor. Connect

the Wind sensor to the Thermo-hygro transmitter

by plugging the connector head into the socket of

the Thermo-hygro sensor.

2. First insert the batteries into the Thermo-hygro sensor and optional rain sensor

(purchased separately) (See How to install and replace the batteries into the

Thermo-hygro sensor and How to install and replace the batteries into the rain

sensor below).

3. Then insert the batteries into the Weather Centre (See How to install and replace

the batteries into the Weather Centre below). Once the batteries are installed, all

segments of the LCD will light up. It will then display the time as 12:00, the date as

1.1.09, the weather icons, and air pressure value. "- - -" will be shown for outdoor

data.

4. The Weather Centre will start receiving data from the transmitter. The transmission

reception icon will be blinking to indicate that the centre is trying to get the thermo-

hygro transmitter data. The outdoor temperature, humidity and wind data should

then be displayed on the Weather Centre. If this does not happen after 135 seconds,

the batteries will need to be removed from all units. You will have to start again from

step 2.

5. The transmitter reception icon is now blinking again to indicate that the centre is

trying to get the rain sensor data. It will stop blinking once the rain sensor has been

detected. If this does not happen after 135 seconds, you will need to start again from

step 2.

6. You may need to check the cable for correct connection and all the components for

correct function by manually turning the wind-gauge by moving the wind-vane; tilting

the rain sensor to hear the impact of the internal moving seesaw, etc. (see

Positioning below).

7. Time and date must be manually set.

8. After the Weather Centre has been checked for correct function with regard to the

above points and found fit, the initial set up of the weather centre system is finished

and the mounting of the system components can take place. It must be ensured

Socket for wind

sensor

however that all components work properly together at their chosen mounting or

standing locations.

Note: After batteries are installed in the transmitter, install the batteries in the weather

centre to receive the signal from the transmitters as soon as possible. If the weather

centre is powered more than 5 hours after the transmitter is powered, the weather centre

will never receive the signal successfully from the transmitters. In this case, you will need

to reinstall the batteries for all the transmitters to redo the setup procedure.

After the batteries are installed, there will be synchronization between weather centre and

the transmitters. At this time, the signal reception icon will be blinking. When the signal

is successfully received by the Weather Centre, the icon will be switched on. (If it is not

successful, the icon will not be shown in LCD) This allows you to see whether the last

reception was successful (icon on) or not (icon off). Short blinking of the icon shows that a

reception is in progress.

If the signal reception is not successful on the first frequency (921MHz) for 45 seconds,

the frequency is changed to 926MHz and the learning is tried another 45 seconds. If still

not successful, the reception is tried for 45 seconds on 916MHz. This will also be done for

re-synchronization.

Transmitter signal reception icon

HOW TO INSTALL AND REPLACE THE BATTERIES INTO THE THERMO-

HYGRO TRANSMITTER

The outdoor Thermo-hygro transmitter works with 2 x AA IEC LR6,

1.5V batteries. To install and replace the batteries, please follow the

steps below:

1. Uninstall the rain cover of the transmitter.

2. Remove the battery compartment cover.

3. Insert the batteries, observing the correct polarity (see the

marking in the battery compartment).

4. Replace the battery cover and the rain cover onto the unit.

Note: When changing batteries in any of the units, all units need to be reset by following

the setup procedure. This is because the thermo-hygro sensor will assign a random

security code at start-up and this code must be received and stored by the weather centre

in the first several minutes of power being supplied to it.

HOW TO INSTALL AND REPLACE THE BATTERIES IN THE WEATHER

CENTRE

The Weather Centre works with 2 x C, IEC LR14, 1.5V batteries. When the batteries need

to be replaced, the low battery symbol will appear on the LCD.

To install or replace the batteries, please follow

the steps below:

1. Remove the battery compartment cover.

2. Insert the batteries observing the correct

polarity (see the marking in the battery

compartment).

3. Replace the battery cover.

HOW TO INSTALL AND REPLACE BATTERIES INTO THE RAIN SENSOR

(OPTIONAL- SOLD SEPERATELY)

To install and replace the batteries, please follow the steps below:

1. Unlock the main cover from the rain sensor base and remove the cover.

2. Remove the battery cover at the top of the rain sensor.

3. Insert 2 x AAA IEC LR3 1.5V batteries into the battery compartment, observing the

correct polarity.

4. Replace the battery cover and the main cover on the unit.

Note: When changing batteries in any of the units, all units need to be reset by following

the setting up procedure. This is because the thermo-hygro sensor and rain sensor

(optional) assign a random security code at start-up and this code must be received and

stored by the Weather Centre in the first 135 seconds of power being supplied to it.

Note: The stored history records will not be retained after battery change or whenever

battery is removed from the Weather Centre.

FUNCTION KEYS:

Weather Centre:

The Weather Centre has 4 easy-to-use function keys.

MIN/MAX key

SET key

+ key

HISTORY key

Figure 1

Figure 2

Figure 3

SET key

Press and hold for 3 seconds to enter manual setting modes: LCD contrast, Manual

time setting, 12/24 hour time display, Calendar setting, ºC/ ºF temperature unit, Wind

speed unit, Rainfall unit, Pressure unit, Relative pressure reference setting, Weather

tendency threshold setting

Press to toggle between the display of Mode 1 or Mode 2:

Mode1: "Wind speed + outdoor temp + rel. pressure"

Mode 2: "Gust + Dew Point temp + rainfall data (only if there is a rain sensor-

optional)"

Note: (Mode 2 displayed will be shown for 30 seconds. Then it will return to normal

display.

Press to activate the reset mode when MAX or MIN record is shown

+ key

In display Mode 1, press to toggle the date, weekday, + date, Indoor temp, or sec

In display Mode 2, press to toggle the Relative Pressure, 24 hour rainfall and Total

rainfall (if there is a rain sensor- optional).

Press to adjust (increase) the level of different settings

Press to confirm to reset the MIN/MAX record

HISTORY key

Press to display the weather data history records or exit manual setting mode

MIN/MAX key

Press to display MIN/MAX records of various weather data or adjust (decrease) the

level of different settings

LCD SCREEN

The LCD screen is split into 3 sections displaying the following information:

1. Time and date/ indoor temp/ second

2. Wind data, outdoor temperature and humidity, dew point, weather forecast icon,

tendency indicator and battery indicators.

3. Air pressure history, relative air pressure, rainfall data (optional)

*When the Weather Centre successfully receives the transmission signals, the icon will

be switched on. (If not successful, the icon will not be shown on the LCD). User can

therefore easily see whether the last reception was successful (“ON” icon) or not (“OFF”

icon). On the other hand, the short blinking of the icon shows that a reception is

being done at that time.

Wind speed / gust in

mph, km/h, m/s

Calendar / indoor

temperature / seconds

display

Weather tendency

indicator

Time display

Air pressure

history histogram

Outdoor relative

humidity in %

Weather forecast

Icon

Relative air pressure /

24 hr rainfall / Total

rainfall display* (only if

there is a rain sensor

being used)

Wind Chill in

C or F

Low battery indicator

(weather centre)

Transmitter signal

reception icon*

Low battery

indicator

(transmitter)

Outdoor

temperature

/ dew point

in C or F

MI/MAX icons

HISTORY

icon

Low battery

indicator (rain

sensor - optional)

In normal display user may press the SET key shortly to toggle between Mode1 and Mode

2 display:

Mode 1: Wind speed, outdoor temperature and relative air pressure are shown.

Mode 2: Wind gust, dew point, and rainfall (optional) readings are shown.

Note: To view the rainfall data, press the +key after entering Mode 2 display.

Wind gust icon

Dew point icon

Rainfall icon

In Mode 2, this reception

icon is showing the

condition of the reception

of the signal from Rain

sensor (only if a rain

sensor is being used)

Wind speed icon

Outdoor temp

icon

Rel. Air Pressure icon

In Mode 1, this reception icon is showing the condition of the

reception of the signal from Thermo-hygro transmitter

Transmitter signal reception icon

POSITIONING:

Using 915MHz wireless transmission gives users little restriction on placement because all

units can be positioned virtually anywhere within a 330 ft / 100 meters radius of the base

station. Please ensure that the cable included in this set meets your distance

requirements (see accessories in the main user manual for adding extension cables).

Important: Ensure all signals can be received and/or all cable distances meet with your

requirements at the point of fixing particularly before you start drilling any mounting holes.

Wind sensor

Secure the main unit to the shaft of the mast holder using the single screw provided with

the front of the sensor (marked E) facing in the East-West direction otherwise wind

direction will not be accurate. Now fix the entire unit to a suitable mast using the U-bolt,

washers and nuts found in this set.

Note: For best results mount the wind sensor onto a mast to allow the wind to freely travel

from all directions to enable an accurate reading (ideal mast size should be from Ø 5/8” to

11/4”). Ensure that the cable of the wind sensor meets your distance requirements

Thermo-hygro Sensor

To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall (2 screws

are supplied), plug the sensor firmly into the wall holder and then carefully replace the rain

cover back over the thermo-hygro sensor.

Note: After mounting the units, should the weather data not be received, user may need to

remove the batteries from all units and redo the set-up procedures after about 5 minutes.

Rain sensor (optional)

The rain sensor should be mounted horizontally about 2-3ft off from the ground (or higher)

in an open area away from trees or other coverings to allow rain to fall naturally for an

accurate reading.

Note: For best results ensure the base is horizontal to allow maximum drainage of any

collected rain

or duplicated or processed using electronic, mechanical or chemical procedures without

written permission of the publisher.

This handbook may contain mistakes and printing errors. The information in this

handbook is regularly checked and corrections made in the next issue. We accept no

liability for technical mistakes or printing errors, or their consequences.

All trademarks and patents are acknowledged.

EJMA1913T910

Printed in China

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-7075U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-179ORV2 Abmessungen

La Crosse Technology

La Crosse Technology WS-8035 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WW85777 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-2317U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3102U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2801-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425C Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1416v2 Installationsanleitung

La Crosse Technology

La Crosse Technology 308-1711BLV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6206 Bedienungsanleitung

La Crosse Technology

La Crosse Technology M82738V2 Abmessungen

La Crosse Technology

La Crosse Technology C87030 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology V40-PRO Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1612 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9031U Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA76669 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009-IT Betriebsanleitung

La Crosse Technology

La Crosse Technology WS-3610 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2315 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WEATHER DIRECT WD-3103U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C80758-UK Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Renkforce

Renkforce 1208067 Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung