La Crosse Technology WS-7013U-IT Bedienungsanleitung

WS-7013U-IT

Wireless 915 MHz

Temperature Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents

Quick Setup

Detailed Setup Guide

Battery Installation

Setting the Time

Features

Minimum and

Maximum

Temperatures

Resetting Minimum

and Maximum

Temperatures

Additional remote

temperature sensors

(optional)

Mounting

Troubleshooting

Maintenance and Care

Specifications

Warranty Information

INVENTORY OF CONTENTS

1. The indoor temperature station

(Figure 1)

2. The remote temperature sensor (TX29U-

IT) and mounting bracket. (Figure 2)

3. 3 each, 1/2” Philips screws.

4. One strip of double sided adhesive tape.

5. Instruction Manual and Warranty Card.

INSTANT TRANSMISSION is the state-of-

the-art new wireless transmission

technology, exclusively designed and

developed by LA CROSSE TECHNOLOGY.

INSTANT TRANSMISSION offers you an

immediate update (every 4 seconds!) of all

your outdoor data measured from the

sensors: follow your climatic variations in

real-time!

This product offers:

ADDITIONAL EQUIPMENT

(not included)

1. 1 Philips screwdriver.

2. 2 Fresh AAA 1.5V batteries.

3. 2 Fresh AA 1.5V batteries

QUICK SETUP

Hint: Use good quality Alkaline Batteries

and avoid rechargeable batteries.

1. Have the indoor temperature station and

remote temperature sensor 3 to 5 feet

apart.

2. Batteries should be out of both units for

10 minutes.

Figure 2

Figure 1

3. Place the batteries into the remote

temperature sensor first then into the

indoor temperature station.

(All remote temperature sensors must be

started before the indoor temperature station)

4. DO NOT PRESS ANY BUTTONS FOR

15 MINUTES.

In this time the indoor temperature station and

remote temperature sensor will start to talk to

each other and the display will show both the

indoor temperature and an outdoor

temperature. If the indoor temperature station

does not display both temperatures after the

15 minutes please retry the set up as stated

above. After both indoor and outdoor

temperatures are displayed for 15 minutes

you can place your remote temperature

sensor outdoors and set your time.

The remote temperature sensor should be

placed in a dry, shaded area. The thermo-

hygro sensor has a range of 330 feet. Keep

in mind that the 330 feet is in open air with no

obstructions and that radio waves DO NOT

curve around objects. Actual transmission

range will vary depending on what is in the

path of the signal. Each obstruction (roof,

walls, floors, ceilings, thick trees, etc.) will

effectively cut signal range in half.

Example: A wireless weather station with a

330 feet range is mounted on an interior wall,

so that the signal has to pass through one

interior wall, one exterior wall, and across the

10 feet width of the room between the 2 walls.

The first wall will reduce the range to 165 feet,

and the second wall will reduce the range to

87 feet. Factoring in the 10 foot room, this

leaves a maximum of 77 feet of remaining

signal range.

This allowance is typically enough for a frame

wall with non-metallic siding; however certain

materials can reduce range even further.

Metal siding, stucco, and some types of glass

can reduce signal range by as much as ¾ or

more, compared to the ½ reduction typical of

most obstructions. It is possible to receive a

signal through these materials, however

maximum range will be much less due to their

tendency to absorb or reflect a much larger

portion of the sensor’s signal.

To complete the set up of your indoor

temperature station after the 15 minutes have

passed please follow the steps below.

1. Press and hold the “SET/CH” button for

5 seconds.

Note: A “12h” or “24h” will appear on the

top line. (“12h” for AM/PM, “24h” for

military time)

2. To change between “12h” and “24h”

press and release the “MIN/MAX” button.

3. When you have your choice shown on

the display press and release the

“SET/CH” button once.

Note: if “12h” is selected, the temperature is

displayed in degree Fahrenheit. If “24h” is

selected, the temperature is displayed in

degree Celsius

4. An hour will now be flashing.

5. Press and release the “MIN/MAX” button

until the correct hour is shown.

Note: When in the 12h mode there is

“PM” displayed under the word TIME

when in the PM hours. During the AM

hours this area will be blank.

6.When the correct hour is shown,

press and release the “SET” button

once.

Press and release the SET button once

more and you are done.

DETAILED SETUP GUIDE

BATTERY INSTALLATION - When one

Temperature sensor is being used

1. First, insert the batteries to the

Temperature sensor (see “A.

Temperature sensor” below).

2. Within 2 minutes of powering up the

sensor, insert the batteries to the

Temperature Station (see “B. Indoor

Temperature station” below). Once the

batteries are in place, all segments of

the LCD will light up briefly. Following

the indoor temperature and the time as

12:00 will be displayed. If they are not

shown in LCD after 60 seconds, remove

the batteries and wait for at least 60

seconds before reinserting them. Once

the indoor data is displayed user may

proceed to the next step.

3. After the batteries are inserted, the

Temperature Station will start receiving

data signal from the sensor. The outdoor

temperature and humidity should then be

displayed on the Temperature Station. If

this does not happen after 2 minutes, the

batteries will need to be removed from

both units and reset from step 1 and the

signal reception icon is no longer shown.

A. REMOTE TEMPERATURE SENSOR

Remove the mounting

bracket.

a. Remove battery

cover

b. Observing the

correct polarity,

install 2 AA

batteries—make

sure they do not

spring free, or start-up problems

may occur. Replace cover.

B. INDOOR TEMPERATURE STATION

Note: After the batteries are installed, DO

NOT press any buttons. This may interfere

with the signals, causing temperatures to

Battery

cove

a. Remove the battery cover on the

backside. To do this, push up and

pull out.

b. Observing the correct polarity,

install 2 AAA batteries.

c. Replace battery cover.

d. Wait 15 minutes to allow both the

indoor and outdoor temperatures are

shown on the indoor temperature

station.

Battery

Cover

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology 328-1414 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8025AL Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1510-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2317 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7395U Bedienungsanleitung

La Crosse Technology

La Crosse Technology SW403 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9133BK-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415BWV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Weather History Interval Handbuch

La Crosse Technology

La Crosse Technology WS1600IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7095U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1409 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-8120U-IT Installationsanleitung

La Crosse Technology

La Crosse Technology 308-1711BLV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology S85814 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1415FCT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 724-1415BL Abmessungen

La Crosse Technology

La Crosse Technology 327-1417 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology WS-8120U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 327-1417BW Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 308-1451H Bedienungsanleitung

La Crosse Technology

La Crosse Technology V10v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology T84237 Bedienungs- und Wartungshandbuch

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung