La Crosse Technology WS-7078UF Bedienungsanleitung

WS-7078UF

Wireless 433 MHz

Radio-controlled Weather Station

Instruction Manual

TABLE OF CONTENTS

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 4

Quick Set-Up Guide 5

Detailed Set-Up Guide

Battery Installation 6

Program Mode

Function Keys 7

12/24 hour Time Setting 8

Time Zone Setting 8-9

Daylight Saving Time Setting 9

Time Setting (WWVB & Manual) 10-11

Setting Day, Date, and Year 11-12

Selecting °F or °C 12

Setting the LCD Contrast 12

Features

Weather Forecast Icons 13-14

Indoor Temperature, Humidity, & Comfort

Level Indicator 15

Outdoor Temperature & Humidity 15

Minimum & Maximum Records (Indoor,

Outdoor, & Resetting) 15-16

Alarm (Setting, Snoozing, & Stopping) 17-18

Additional Remote Thermo/hygro Sensors

(Set-Up, Viewing, & Operation) 18-19

Mounting 20-21

Troubleshooting 22

Maintenance & Care 23

Specifications 24

Warranty Information 25-26

INVENTORY OF CONTENTS

1. The indoor weather station (Figure 1).

2. One TX4U remote thermo/hygro sensor with mounting bracket (Figure

2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1. Four, fresh AA 1.5V batteries.

3. One, Philips screwdriver.

4. One, Flat screwdriver.

Figure 1

Time LCD

Date LCD

Forecast LCD

Indoor LCD

Outd

oor LCD

Figure 2

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal

can be received up to 2, 000 miles away through the internal antenna in the weather

station. However, due to the nature of the Earth’s Ionosphere, reception is very

limited during daylight hours. The weather station will search for a signal every

night when reception is best. The WWVB radio station derives its signal from the

NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is

continually measuring every second, of every day, to an accuracy of ten billionths of

a second per day. These physicists have created an international standard,

measuring a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

For more information about WWVB please see the NIST website at

http://www.boulder.nist.gov/timefreq/stations/wwvb.htm

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote thermo/hygro sensor 3 to 5

apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote thermo/hygro sensor first then into

the indoor weather station.

(All remote thermo/hygro sensors must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the indoor weather station and remote thermo/hygro sensor will start to

talk to each other and the indoor weather station will show both the indoor

temperature and humidity and the outdoor temperature and humidity. If the indoor

weather station does not display all values after the 10 minutes please retry the set up

as stated above. After all values are displayed for 10 minutes you can place your

remote thermo/hygro sensor outdoors and set your time.

The remote thermo/hygro sensor should be placed in a dry, shaded area. The remote

thermo/hygro sensor has a range of 80 feet. Any walls that the signal will have to

pass through will reduce distance. An outdoor wall or window will have 20 to 30

feet of resistance and an interior wall will have 10 to 20 feet of resistance. Your

distance plus resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote thermo/hygro sensor but direct rain

must be avoided.

To complete the set up of your indoor weather station after the 10 minutes

have passed please follow the steps in the Detailed Set Up Guide

Note: The Thermo Hygro Sensor transmits a signal every 3 minutes; after

the batteries have been installed, the Weather Station will search for the

signal for a duration of 5 minutes. If there is no temperature reading in the

OUTDOOR LCD after 5 minutes, make sure the units are within range of

each other, or repeat the battery installation procedure.

DETAILED SET-UP GUIDE

BATTERY INSTALLATION

A. Remote Thermo/hygro Sensor

1. Pull the cylindrical rain cover off the remote

thermo/hygro sensor.

2. Remove the battery cover (located on the backside

of the remote thermo/hygro sensor, above the

mounting post and bracket).

3. Press the arrow and slide the battery cover off.

4. Observing the correct polarity install 2 AA

batteries.

5. Replace battery cover, and place rain cover snugly onto the remote

thermo/hygro sensor.

B. Indoor Weather Station

1. Remove the battery cover. To do this, insert a

solid object in the space provided at the lower-

central position of the battery cover, then push

up and pull out on the battery cover.

2. Observe the correct polarity, and install 2 AA

batteries.

Replace the battery cover.

Note: Immediately after the batteries have been installed, each LCD

(Liquid Crystal Display) will flash, and a tone will sound. Within a few

seconds the indoor temperature, indoor relative humidity, and the

weather icons (sun and clouds) will be displayed. If these items are not

displayed remove the batteries for 10 seconds and reinstall. If the

outdoor temperature is not displayed within four minutes, remove the

batteries from both units, wait 10 seconds, and reinstall. The time will

show -:-- and start searching for the signal. If it successfully receives

the time signal (reception is achieved easiest at night), it will display the

correct time (factory setting is Eastern time zone).

Battery

Cover

PROGRAM MODE

Programming Note: If 30 seconds is allowed to pass, or either the “IN” or

the “OUT” buttons are pressed during programming modes the unit will

confirm/set the last information entered—the display will stop flashing and

return to normal time-date readings. If you don’t leave the program

sequence during the programming of sections “A” through “G”, you can

advance to step 4 of the next program section. If you do leave the program

sequence (or want to program a specific setting) follow each instructional

step to program that setting. The programming sequence is as follows:

•12 or 24 Hour Time Setting

•Time Zone Setting

•Daylight Saving Time(DST) Setting

•Time Setting

•Day, Date and Year Setting

•

F or

C Setting

•LCD Contrast Setting

FUNCTION KEYS

The Secondary Buttons are located directly below the Primary Buttons, and

behind the La Crosse Technology shield on the face of the unit. To access

the Secondary Buttons: place a solid object in the slot (above the shield)

and gently pull out and down.

Primary Buttons

Secondary Buttons

A. 12 or 24 Hour Time Setting

1. Press and hold the “SET” button for 3 seconds or until “12h”

or “24h” flashes in the DATE LCD.

2. Press and release the “CH” button to toggle between 12 and

24-hour time.

3. Press and release the “SET” button to confirm the 12/24-hour

time setting and to advance to Time Zone Setting.

B. Time Zone Setting

The default time zone is EST, “-5hr” (Eastern Standard Time), to

change this setting:

1. Press and hold the “SET” button for 3 seconds or until “12h”

or “24h” flashes in the DATE LCD.

2. Press and release the “SET” button 1 time to enter the Time

Zone setting mode.

3. The default Time Zone “-5” will flash in the DATE LCD.

4. Press and release the “CH” button to select your appropriate

time zone. During selection of the Time Zone, the 3 letter

abbreviations for the time zones found in North America will

flash across the top of the TIME LCD. Observe the chart

below showing the corresponding abbreviations, time zones,

and codes.

TIME ZONES

GMT 0

Atlantic -4

EST Eastern -5

CST Central -6

MST Mountain -7

PST Pacific -8

ALA Alaska -9

HAW Hawaii -10

Note: There are more time zones represented by numbers than

there are represented by 3 letter abbreviations. If you live in

North America you need only be concerned with the ones in the

chart above.

5. Press and release the “SET” button to confirm your selection

and advance to the Daylight Saving Time setting.

C. Daylight Saving Time(DST) Setting

1. Press and hold the “SET” button for 3 seconds or until “12h”

or “24h” flashes in the DATE LCD.

2. Press and release the “SET” button 2 times to reach the DST

selection mode.

3. “DST 1” is the default (factory) setting and will be flashing in

the DATE LCD.

4. Press and release the “CH” button to select “DST 0” or “DST

1.”

“DST 0” indicates that the feature is off and the indoor weather

station will not change times at the daylight saving time changes

automatically. “DST 1” indicates that the feature is on and the

indoor weather station will change times at the daylight saving

time changes automatically.

Note: Some locations (Arizona and parts of Indiana) do not

follow Daylight Saving Time, and should select “DST 0.”

5. Press and release the “SET” button to confirm your selection

and advance to the Time setting mode.

D. Time

There are two methods by which the time can be set:

1. Automatically via WWVB reception, or

2. Manually.

1. WWVB (Remote Control Time)

This method requires you to do nothing, except wait for the signal

to be received and to select a time zone. Reception usually takes

approximately 6-10 minutes during optimal conditions. The best

conditions for reception is at night, between midnight and 6:00

am—when there is less atmospheric interference. To keep your

time as accurate as possible, the indoor weather station conducts a

WWVB search every night between these hours and overrides any

manually set time. The WWVB tower icon (appearing in the TIME

LCD) will flash when a signal-search is in progress, will remain

steady when the signal has been received, and nothing will be

displayed in all other situations. If the WWVB time has not been

received 10 minutes after battery installation you may manually set

the time or wait for WWVB reception. Once the WWVB time

signal is received it will override the manually set time.

2. Manual Time Setting

a. Press and hold the “SET” button for 3 seconds or

until “12h” or “24h” flashes in the DATE LCD.

b. Press and release the “SET” button 3 times.

c. The hour digit will be flashing in the TIME LCD.

d. Press and release the “CH” button to change the

hour – increasing the hours by increments of 1 with

each press of the “CH” button.

e. Press and release the “SET” button to confirm the

hour setting and to advance to the minute setting

mode.

f. The minute digits should be flashing. Press and

release the “CH” button to change the minutes—

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS9123IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1417BLV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9043U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2210 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-805 Installationsanleitung

La Crosse Technology

La Crosse Technology WS-7025U Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX233RW Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7097U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7078TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84612 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7136U Bedienungsanleitung

La Crosse Technology

La Crosse Technology T83653v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V10-TH Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9410TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84612 Betriebsanleitung

La Crosse Technology

La Crosse Technology 308-1409BTV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415BW Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7212U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-2513U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6818 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1451v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-62U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7208TWC Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung