La Crosse Technology WS-7394U Bedienungsanleitung

WS-7394U

Wireless 433 MHz

Weather Station

Instruction Manual

FCC DISCLAIMER

FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter)

This device complies with part 15 of the FCC rules. Operation is sub-

ject to the following two conditions:

(1)This device may not cause harmful interference.

(2)This device must accept any interference received, including inter

ference that may cause undesired operation.

Contents

Language Page

English 2

French 18

Spanish 36

TABLE OF CONTENTS

Topic Page

Inventory of Contents/ Additional Equipment 3

About WWVB 3

Quick Set Up Guide 4

Detailed Set Up Guide

Battery Installation 5

Start Up Sequence 6

Explanation of LCD Information 7

Function Key Layout 8

Program Mode

Overview of Programming Sequence 8

LCD Contrast Setting 8

Time Zone Setting 9

DST ON/OFF Setting 9

Radio-controlled Time ON/OFF Setting 10

12/24-hour Time Mode Setting 10

Setting the Time/Date Manually 11

Temperature Measuring Units (˚F/˚C) 12

Air Pressure Measuring Units (inHg/hPa) 13

Relative Pressure Setting 13

Forecast Sensitivity Setting 14

Features and Operation

Minimum/Maximum Temperature/Humidity 14

Multiple Remote Temperature/Humidity Sensors 15

Comfort Icon 16

Weather Forecast and Pressure Trend Indicators 16

Weather Icons 17

Weather Tendency Arrows 17

Barometric Air Pressure Reading 18

Air Pressure History Bar Chart 18

Mounting 19

Maintenance and Care 20

Troubleshooting Guide 20

Specifications 21

Warranty Information 22

P.2

INVENTORY OF CONTENTS

1. WS-7394U-indoor weather station

2. TX6U-remote temperature (temperature/humidity) sensor

3. Instruction manual and warranty card

ADDITIONAL EQUIPMENT (not included)

1. Five fresh AA 1.5V alkaline batteries.

2. One wall-mounting screw (optional)

ABOUTWWVB (radio-controlled time)

The NIST (National Institute of Standards and Technology-Time and

Frequency Division) radio station, WWVB, is located in Ft. Collins,

Colorado and transmits the exact time signal continuously throughout

the United States at 60 kHz. The signal can be received up to 2,000

miles away through the internal antenna in the indoor weather station.

However, due to the nature of the Earth’s Ionosphere, reception is

verylimited during daylight hours. The indoor weather station will search

for a signal every night when reception is best. TheWWVB radio sta-

tion derives its signal from the NIST Atomic clock in Boulder, Colorado.

A team of atomic physicists continually measure every second of ev-

ery day to an accuracy of ten billionths of a second a day. These

physicists have created an international standard, measuring a sec-

ond as 9,192,631,770 vibrations of a Cesium 133 atom in a vacuum.

For more information about WWVB please see the NIST website at

http://www.boulder.nist.gov/timefreq/stations/wwvb.htm

QUICK SET-UP GUIDE

Hint:

Use good quality Alkaline Batteries and avoid rechargeable

batteries.

1. Have the indoor weather station and remote temperature sensor 3

to 5 apart.

2. Batteries should be out of both units for 15 minutes.

3. Place the batteries into the remote temperature sensor first then

into the indoor weather station.

(All remote temperature sensors must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES.

In this time the indoor weather station and remote temperature sensor

will start to talk to each other and the indoor weather station will show

both the indoor temperature and humidity and the outdoor temperature.

If the indoor weather station does not display all values after the 15

minutes please retry the set up as stated above. After all values are

displayed for 15 minutes you can place your remote temperature sen-

sor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded

area. The remote temperature sensor has a range of 330 feet. Any

walls that the signal will have to pass through will reduce distance. An

outdoor wall or window will have 20 to 30 feet of resistance and an

interior wall will have 10 to 20 feet of resistance. Your distance plus

resistance should not exceed 330 ft.in a straight line.

NOTE:

Fog and mist will not harm your remote temperature sensor

but direct rain must be avoided.

To complete the set up of your indoor weather station after the 15

minutes have passed please follow the steps in the Detailed Set Up

Guide.

Note:

The remote temperature sensor transmits a signal every 3

minutes; after the batteries have been installed, the indoor weather

station will search for the signal for a duration of 5 minutes. If there is

no temperature reading in the OUTDOOR LCD after 5 minutes, make

sure the units are within range of each other, or repeat the battery

installation procedure.

GB P.3 GB

P.4

DETAILED SET-UP GUIDE

I. Battery Installation

Batteries will fit tightly. To avoid start-up problems, make sure that the

batteries do not spring free. Also be sure to insert alkaline batteries

intothe remote temperature sensor first, thentheindoorweatherstation.

Initial set up should be done with the remote temperature sensor and

indoor weather station in the same room.The units should be perma-

nently mounted only after the signal reception has been verified.

A. RemoteTemperature and Humidity Sensor

1. Remove the mounting bracket. The bracket snaps on and off easily.

2. Remove the battery cover, by sliding the cover down.

3. Observing the correct polarity install 2 AA batteries. The batteries

will fit tightly (to avoid start-up problems make sure they do not

spring free).

4. Replace the battery cover by sliding upwards.Be sure battery cover

is on securely.

B. IndoorWeather Station

1. Remove the battery cover (the cover has white writing on it).

2. Observe the correct polarity, and install two Alkaline AA batteries.

3. Do not press any buttons for at least ten minutes. If a button is

pressed before the indoor weather station has received informa-

tion from the TX6U sensor, no data will be received from that sen-

sor until reset.

4. Replace the battery cover.

II. Start Up Sequence

A. Initial Start

1. Immediately after the batteries have been installed the LCD will

completely light up for a brief moment.

2. All information will then appear in normal mode, with “12:00”as the

default time and “WE.1” as the default date (2004 as the year).

3. The indoor temperature and humidity, and barometric air pressure

(as 29.91 inHg relative RH) will also be displayed.

4. There is a “satellite”icon that appears in the bottom portion of the

LCD, to the left of the outdoor temperature- this icon informs the

user that the indoor weather station is looking for signals from the

remote temperature sensor. Within five minutes the remote tem-

perature should be displayed-if not, remove batteries from all units

and repeat battery installation, the remote temperature sensor first,

then the indoor weather station.

B. WWVB Reception

1. Once the batteries are installed in the indoor weather station it will

automatically search for the WWVB signal. If it receives a good

signal (which is unlikely during daylight hours in most locations),

the WWVB reception indicator (looks like a tower icon) will flash.

The indoor weather station requires five full minutes of good recep-

tion to successfully capture the signal and set to the correct hour,

minute, second, month, day and year.If the signal reception is not

successful within ten minutes, the signal search will be cancelled

and will automatically resume every two hours until the signal is

successfully captured.

2. The signal is sent from Ft. Collins, Colorado only and is similar to

an AM radio signal. Atmospheric interferences such as storms,

sunspots, and even sunlight will cause the signal to not travel as

far.

3. To maximize reception, place the indoor weather station in a win-

dow facing Colorado, at least six feet from any electrical source

(computers, televisions, refrigerators, etc.). Do not move the in-

door weather station while it is searching for the signal.

4. The time and date can be manually set.Once the signal is captured,

it will override any time and date set to the time zone selected.

Battery Cover

GB P.5 GB

P.6

5. Once the time and date are set, the indoor weather station will

conduct a search every night at midnight and correct to the accu-

rate time and date (Daylight SavingTime is automatic).If the signal

has been received in the past 24 hours, the reception indicator will

be displayed.

III. Explanation of LCD Information

A. The below picture highlights the LCD features.

B. There are many different modes the indoor weather station can be

set to.The LCD shown is the normal operating mode, and your

actual data shown will be different based on your local settings and

conditions.

IV.Function Key Layout

A. The below picture shows the four function keys used in program-

ming and operation of your indoor weather station

V. Program Mode

The program mode is laid out in a manner that allows you to program

each function separately, or you can follow the instructions entirely to

program the indoor weather center. Complete programming is usually

done for the initial set-up, and will require you to skip step 1,2 and 3 of

each programming section. The programming mode can be exited at

any time by either pressing the“CH” button, or waiting for the 15-sec-

ond time-out to take effect.

A. Overview of programming mode sequence

1. LCD Contrast 2. Time Zone 3. DST ON/OFF

4. Radio-controlled 5. 12/24-hour 6. Hour

Time ON/OFF time mode

7. Minute 8. Year 9. Month

10. Date 11. ˚F/˚C 12. inHg/hPa

13. Relative pressure setting 14. Forecast sensitivity

B. LCD Contrast Setting

1. Press and hold the “SET”button for five seconds.

Radio-controlled

time

WWVB Reception

Indicator

Date Display

Comfort Icon

Indoor Temperature

Humidity Display

Air Pressure Trend

Indicator

Forecast Icon

Barometric Air

Pressure

12-hour Air

Pressure History

Outdoor

Temperature Display Remote Sensor

Number (Up to 3

Total)

GB P.7 GB

P.8

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “OUT/+” button to select the desired LCD

contrast setting.

4. Press and release the “SET” button to confirm the LCD contrast

setting and continue to theTime Zone setting.

C. Time Zone Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button once more to advance to the

Time Zone setting.

4. A number will flash to the left of the letter “h”at the top of the display

just below the time display.

5. Press and release the “OUT+” button to select the desired time

zone.

6. Press and release the “SET”button to confirm the Time Zone set-

ting and continue to the DST ON/OFF setting.

D. DST ON/OFF Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button twice more to advance to the

DST ON/OFF setting.

4. “DST” will appear above the indoor temperature/humidity display

and “ON”or “OFF”will flash above that.

5. Press and release the “OUT/+”button to select DST ON/OFF.

Note:

Some locations (Arizona and parts of Indiana) do not follow

Daylight Saving Time.

6. Press and release the “SET” button to confirm the DST ON/OFF

setting and continue to the Radio-controlledTime ON/OFF setting.

E. Radio-controlled Time ON/OFF Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button three more times to advance to

the Radio-controlled time ON/OFF setting.

4. “RCC” will appear above the indoor temperature/humidity display

and “ON”or “OFF”will flash above that.

5. Press and release the “OUT/+” button to select Radio-controlled

time ON/OFF setting.

6. Press and release the “SET”button to confirm the Radio-controlled

time ON/OFF setting and continue to the 12/24-hour Time Mode

setting.

F. 12/24-hour Time Mode

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button four more times to advance to

the 12/24-hour time mode setting.

4. “12h” or “24h” will flash above the indoor temperature/humidity

display.

5. Press and release the “OUT/+”button to select 12 or 24-hour time

mode.

GB P.9 GB

P.10

Note:

In 12h mode “PM”will appear to the left of the time during PM

hours. If the time is not within the PM hours nothing will be displayed.

Be sure to set the time to the correct AM/PM time to ensure automatic

reception.

6. Press and release the “SET”button to confirm the 12/24-hour time

mode setting and continue to the Hour setting

G. Setting The Hour Manually

The WWVB signal will override any manual set time and date

information.The time will be based on the time zone selected.

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button five more times to advance to

the Manual Hour setting.

4. The hour will begin to flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired hour.

6. Press and release the “SET”button to confirm the hour setting and

continue to the Minute setting.

H. SettingThe Minutes Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button six more times to advance to

the Manual Minutes setting.

4. The minutes will begin to flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired minutes.

6. Press and release the “SET” button to confirm the minutes and

continue to theYear setting.

I. SettingTheYear Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button seven more times to advance

to the ManualYear setting.

4. The year will begin to flash below the time display.

5. Press and release the “OUT/+”button to select the desired year.

6. Press and release the “SET” button to confirm the year and con-

tinue to the Month setting.

J. SettingThe Month Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button eight more times to advance to

the Manual Month setting.

4. The Month will begin to flash below the time display.

5. Press and release the “OUT/+”button to select the desired month.

6. Press and release the “SET”button to confirm the month and con-

tinue to the Date setting.

K. SettingThe Date Manually

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button nine more times to advance to

the Manual Date setting.

4. The date will begin to flash below the time display.

5. Press and release the “OUT/+”button to select the desired date.

6. Press and release the “SET” button to confirm the date and con-

tinue to the Temperature Measuring Units setting.

L.Temperature Measuring Units Selection (˚F or ˚C)

1. Press and hold the “SET”button for five seconds.

GB P.11 GB

P.12

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET” button ten more times to advance to

the Temperature Measuring Units setting.

4. ˚F or ˚C will flash at the top of the display.

5. Press and release the “OUT/+” button to select the desired tem-

perature-measuring unit.

6. Press and release the “SET” button to confirm the temperature-

measuring unit and continue to the Air Pressure Measuring Units

setting.

M. Air Pressure Measuring Units Selection (inHg/hPa)

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button eleven more times to advance

to the Air Pressure Measuring Units setting.

4. inHg or hPa will flash at the top of the display.

5. Press and release the “OUT/+”button to select the desired air pres-

sure-measuring unit.

6. Press and release the “SET” button to confirm the air pressure-

measuring unit and continue to the Relative Pressure setting.

N. Relative Pressure Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button twelve more times to advance

to the Relative Pressure setting.

4. The barometric air pressure will flash in the middle of the display,

just below the forecast icon

5. Press and release the “OUT/+”or “IN” button to select the desired

air pressure-measuring unit.

6. Press and release the “SET”button to confirm the relative pressure

setting and continue to the Forecast Sensitivity setting.

O. Forecast Sensitivity Setting

1. Press and hold the “SET”button for five seconds.

2. “lcd” will appear at the top of the display and a number will flash

next to it.

3. Press and release the “SET”button thirteen more times to advance

to the Forecast sensitivity setting.

4. The two air pressure tendency arrows will begin flashing on either

side of the forecast icon and a flashing number will appear under

the forecast icon.

5. Press and release the “OUT/+”button to select the desired forecast

sensitivity setting.

Note:

Barometric air pressure is usually reported as “relative air

pressure”.This reading is based on the combination of absolute air

pressure and altitude.In general, an increase in altitude will result in a

decrease in air pressure. Relative air pressure will make readings in

nearby locations relative to each other to allow for proper forecasting.

The absolute air pressure reading in the Weather Center cannot be

calibrated, only the relative air pressure.

6. Press and release the “SET”button to confirm the forecast sensi-

tivity setting.

THE MANUAL SETTING IS NOW COMPLETED

FEATURES AND OPERATIONS

A. Minimum and MaximumTemperature and Humidity

1. Indoor Minimum and MaximumTemperature and Humidity

The indoor weather station automatically stores the minimum and

maximum indoor temperature and humidity. The minimum and maxi-

mum values are updated automatically when a new minimum or maxi-

mum is recorded, or until manually reset.

a. From the normal display mode, press and release the “IN”key

once to view the indoor maximum temperature and humidity

GB P.13 GB

P.14

(“MAX” will be displayed above the indoor temperature and

humidity).

b. Press and release the “IN” key again to view the indoor mini-

mum temperature and humidity.

c. Press and release the “IN” key again to return to the normal

mode (timeout of viewing minimum/maximum values will occur

if no keys are pressed for fifteen seconds).

Note:

To reset the indoor minimum and maximum temperature and

humidity, first display the values you wish to reset (minimum or

maximum). Next press and hold the “SET” key for at least three

seconds. You will see then that the values will reset to the current

temperature and humidity and corresponding time.

2. Outdoor Minimum and MaximumTemperature

The indoor weather station automatically stores the minimum and

maximum outdoor temperature.The minimum and maximum values

are updated automatically when a new minimum or maximum is

recorded, or until manually reset.

a. From the normal display mode, press and release the “OUT/+”

key once to view the outdoor maximum temperature (“MAX”will

be displayed above the outdoor temperature).

b. Press and release the “OUT/+” key again to view the outdoor

minimum temperature.

c. Press and release the “OUT/+”key again to return to the normal

mode (timeout of viewing minimum/maximum values will occur

if no keys are pressed for fifteen seconds).

Note:

To reset the outdoor minimum and maximum temperature, first

display the values you wish to reset (minimum or maximum). Next

press and hold the “SET”key for at least three seconds. You will see

then that the values will reset to the current temperature and corre-

sponding time.

B. Multiple RemoteTemperature Sensors

The WS-7394U is able to receive signals from 3 different remote

sensors.These extra remote sensors can be purchased through the

same dealer as this unit. A TX4U will monitor the temperature and

humidity, a TX3U will monitor temperature and display the tempera-

ture on its LCD, a TX3UP will monitor the temperature via a probe for

measuring soil or water temperatures and a TX6U will monitor the

temperature only.

Note:

When setting up multiple units it is important to insert batteries

first into all the remote sensors, and in numeric sequence. Second

install batteries into the indoor weather station. Transmission prob-

lems will arise if this is not done correctly and if the total time for set-up

exceeds 6 minutes

1. Set Up of Multiple Units

a. It is necessary to remove the batteries from all units currently in

operation.

b. Remove the battery covers to all remote sensors.

c. Place all remote sensors in a numeric sequential order.

d. In sequential order, install batteries following the same battery in-

stallation procedures seen in Detailed Set-Up Guide section of this

manual.

e. Install batteries into the indoor weather station.

f. Follow the Detailed Set-Up Guide for programming and operating

instructions.

2. Viewing and Operating with Multiple Remote Sensors

a. To view the temperature of a different remote sensor press and

release the “CH” button. A shift from one “boxed” number to the

next should be observed in the OUTDOOR LCD.

b. The minimum and maximum temperature of the additional remote

sensor can be displayed by pressing the “OUT/+”button.

c. To reset the minimum and maximum temperature readings press

and hold the “SET”button for 3 seconds and that temperature record

for that remote sensor will be reset only.

Each remote sensor will have its own minimum and maximum values

stored.

C. Comfort Indicator for IndoorTemperature and Humidity

1. The comfort level indicator appears inbetween the indoor

tempearture and humidity.

2. The indicator will display a “happy-face” when the temperature is

between 68˚F and 79˚F (20˚C and 25.9˚C), and the humidity is

between 45% and 64%.

3. A “sad-face” will be displayed when the temperature and humidity

are outside the mentioned ranges.

D. Weather Forecast Icon and PressureTrend Indicators

The weather forecasting feature is estimated to be 75% accurate, and

is based solely upon the change of air pressure over time. The WS-

7394U averages past air-pressure readings to provide an accurate

GB P.15 GB

P.16

forecast-creating a necessity to disregard all weather forecasting for

12-24 hours after the unit has been set-up, reset, or moved from one

altitude to another (i.e.from one floor of a building to another floor). In

areas where the weather is not affected by the change of air pressure,

this feature will be less accurate.

1. Weather Icons

a. There are 3 possible weather icons that will be displayed at various

times in the center of the indoor weather station.

iSunny-indicates that the weather is expected to improve (not

that the weather will be sunny).

ii Sun with Clouds-indicates that the weather is expected to be

fair (not that the weather will be sunny with clouds).

iii Clouds with Rain-indicates that the weather is expected to get

worse (not that the weather will be rainy).

b. The weather icons change when the unit detects a change in air

pressure.

c. The icons change in order, from “sunny” to “sun with clouds” to

“clouds with rain” or the reverse.

d. It will not change from “sunny”directly to “clouds with rain”, although

it is possible for the change to occur quickly.

e. If the symbols do not change, the weather has not changed (or the

change has been slow and gradual).

f. The sensitivity of the change in foreacst icon is set by the user in

section F of the Detailed Set Up Guide.

E. WeatherTendency Arrows

1. Along with the forecast icon there is a pressure tendency arrow.

2. There is one that points up (on the left side of the LCD) and one

that points down (on the right side of the LCD).

3. These arrows reflect current changes in the air pressure.

4. An arrow pointing up indicates that the air pressure is increasing

and the weather is expected to improve or remain good.

5. An arrow pointing down indicates that the air pressure is decreas-

ing and the weather is expected to become worse or remain poor.

6. No arrow means the pressure is stable.

Pressure trend arrow

7. A storm can be expected if there is a drop of 4 hPa or more in less

than 6 hours. The clouds with rain icon will be displayed and the

tendency arrow that points down will be flashing-indicating the storm

warning feature has been activated. The flashing will stop when

the air pressure stabilizes or begins to rise.

F. Barometric Air Pressure Reading

1. The actual barometric air pressure is displayed directly under the

weather forecast icon

2. The relative air pressure is calibrated by the user through the pro-

gramming mode.

3. Please Follow the programming instructions in section F of the De-

tailed Set Up Guide to set this feature.

G. Air Pressure History Bar Chart

1. The bar graph shows in hPa (Hekto Pascal) the recorded air pres-

sure over the past 12-hours.

2. The horizontal axis shows the hours at increments of -12 hours, -9

hours, -6 hours, -3 hours, and 0 hours (current).

3. The vertical axis is set by hPa: the “0” on this axis represents the

current hPa, and + or - 1,3,5, or 7 shows (in hPa) how high or low

the past air pressure was as compared to the current one.

4. The “0”on the vertical axis indicates the current air pressure value.

5. The “0h”on the horizontal axis indicates the current hour, thus the

current air pressure also.

6. Each bar on the bar graph represents a value of 0.03 hPa, and

each bar also has a corresponding value on the verticle axis.

7. Air pressure trends can be determined by simply glancing at the

bar graph.

a. If the bars are rising (higher on the right than the left) then the

air pressure has a rising trend, and the weather should improve.

b. If the bars are dropping (lower on the right than the left) then the

air pressure has a falling trend, and the weather should worsen.

8. Multiply the two values to find past air pressure (note the + or - sign

of values on the verticle axis); i.e. 0.03 hPa x 3 = 0.09 hPa, now

add this value to the air pressure (in LCD 4) to evaluate what past

air pressures have been.

9. The bar chart will constantly scroll to avoid burnout of the LCD.

Note:

This feature cannot be turned off.

GB P.17 GB

P.18

Andere Handbücher für WS-7394U

Inhaltsverzeichnis

Sprachen:

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology S88907V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9023U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9740U-IT-NRC Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1416v2 Installationsanleitung

La Crosse Technology

La Crosse Technology T83653v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology S88785 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009BK-IT Abmessungen

La Crosse Technology

La Crosse Technology C83100 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6812 Bedienungsanleitung

La Crosse Technology

La Crosse Technology V30 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C75747-AU Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8015TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WA-1030U Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9170U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 327-1414Wv2 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology Wireless Weather Station Abmessungen

La Crosse Technology

La Crosse Technology WS-9005TWC-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7095U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1510-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1517 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7032U Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology C84428 Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung