La Crosse Technology WS-9016U Bedienungsanleitung

WS-9016U

Wireless 433 MHz

Radio-controlled

Sun/Moon Weather Station

Instruction Manual

Topic Page

Inventory of Contents/Additional Equipment 3

About WWVB 4

Quick Set-Up Guide 5

Detailed Set-Up Guide

Battery Installation 6

Program Mode

Function Keys 7-8

LCD Screen 9

Manual Settings Sequence 9

LCD Contrast Setting 10

City Location Setting 10

Time Zone Setting 11

Daylight Saving Time (DST) Setting 11

WWVB On/Off Setting 12

12/24 Hour Setting 12

Manual Time Setting 13

Calendar Setting 14

Snooze Setting 15

ºF/ºC Setting 15

Weather Forecast Icon Sensitivity Setting 16

Features

Alarm Setting 16-17

Sunrise/set – Moonrise/set Information 17-18

Moon Phase Symbols 18

Indoor Temperature and Humidity 18

Weather Forecast and Tendency 19-20

Outdoor Temperature 20-21

Adding Remote Temperature Sensors 21-22

Set-up of Multiple Remote Temperature Sensors 22

Mounting 22-24

City List 25

Troubleshooting 26

Maintenance & Care 27

Specifications 28

Warranty Information 29-30

Table Of Contents

INVENTORY OF CONTENTS

1. The indoor weather station (Figure 1).

2. One TX6U remote temperature sensor with mounting bracket

(Figure 2).

3. Three each, ½” Philips screws.

4. One strip double-sided adhesive tape.

5. Instruction manual and warranty card.

ADDITIONAL EQUIPMENT (not included)

1. Two, fresh AA 1.5V batteries for indoor weather station.

2. Two, fresh AA 1.5V batteries for remoter temperature sensor.

3. One, Philips screwdriver for mounting.

Time LCD

Sun/moon

LCD

Forecast LCD

Indoor LCD

Outdoor LCD

Figure 1

Hanging hole

Battery

compartment

Removable

stand

Figure 2

Mounting

Bracket

Battery

compartment

ABOUT WWVB (Radio Controlled Time)

The NIST (National Institute of Standards and Technology—Time and Frequency

Division) WWVB radio station is located in Ft. Collins, Colorado and transmits the

exact time signal continuously throughout the United States at 60 kHz. The signal

can be received up to 2, 000 miles away through the internal antenna in the weather

station. However, due to the nature of the earth’s ionosphere, reception is very

limited during daylight hours. The weather station will search for a signal every

night when reception is best. The WWVB radio station derives its signal from the

NIST Atomic clock in Boulder, Colorado. A team of atomic physicists is

continually measuring every second, of every day, to an accuracy of ten billionths of

a second per day. These physicists have created an international standard measuring

a second as 9,192,631,770 vibrations of a Cesium-133 atom in a vacuum.

QUICK SET-UP GUIDE

Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries.

1. Have the indoor weather station and remote temperature sensor 3 to 5

feet apart.

2. Batteries should be out of both units for 10 minutes.

3. Place the batteries into the remote temperature sensor first then into

the indoor weather station.

(All remote temperature sensors must be started before the indoor

weather station)

4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.

In this time the indoor weather station and remote temperature sensor will start to

talk to each other and the indoor weather station will show both the indoor

temperature and an outdoor temperature. If the indoor weather station does not

display both temperatures after the 10 minutes please retry the set up as stated above.

After both indoor and outdoor temperatures are displayed for 10 minutes you can

place your remote temperature sensor outdoors and set your time.

The remote temperature sensor should be placed in a dry, shaded area. The remote

temperature sensor has a range of 80 feet. Any walls that the signal will have to pass

through will reduce distance. An outdoor wall or window will have 20 to 30 feet of

resistance and an interior wall will have 10 to 20 feet of resistance. Your distance

plus resistance should not exceed 80 ft. in a straight line.

NOTE: Fog and mist will not harm your remote temperature sensor but direct rain

must be avoided.

To complete the set up of your indoor weather station after the 10 minutes have

passed please follow the steps starting on page 6.

Note: The remote temperature sensor transmits a signal every 3 minutes;

after the batteries have been installed, the indoor weather station will

search for the signal for a duration of 5 minutes. If there is no temperature

reading in the OUTDOOR LCD after 5 minutes, make sure the units are

within range of each other or repeat the battery installation procedure.

DETAILED SET-UP GUIDE

I. Battery Installation

A. Remote Temperature Sensor

1. Remove the mounting bracket. The bracket

snaps on and off easily.

2. Remove the battery cover, by sliding the cover

down.

3. Observing the correct polarity install 2 AA

batteries. The batteries will fit tightly (to avoid

start-up problems make sure they do not spring

free).

4. Replace the battery cover by sliding upwards. Be

sure battery cover is on securely.

B. Indoor Weather Station

1. Remove the battery cover. To do this,

insert a solid object in the space provided

at the lower-central position of the battery

cover, then push up and pull out on the

battery cover.

2. Observe the correct polarity, and install 2 AA batteries.

3. Replace the battery cover.

Note: Immediately after the batteries have been installed, each LCD

(Liquid Crystal Display) will flash and a tone will sound. Within a few

seconds the indoor temperature, indoor relative humidity and the weather

icons (sun and clouds) will be displayed. If not, then remove batteries for

10 seconds and reinstall. If the outdoor temperature is not displayed within

four minutes, remove batteries from both units, wait 10 seconds, and

reinstall. The time will show -:-- and start searching for the signal. If it

successfully receives the time signal (usually at night), it will display the

correct time (default is Eastern).

II. Program Mode

Programming Note: If 30 seconds are allowed to pass or either the IN or the OUT

button is pressed during programming modes, the unit will set the last information

entered—the display will stop flashing and return to normal time-date readings.

A. Function Keys

Weather Station:

The Weather Station has 8 easy to use function buttons; 6 behind the right

front panel of the Weather Station and 2 on the front:

1. SET button

•Enter manual setting modes: LCD contrast, city location, time

zone, DST ON/OFF, WWVB ON/OFF, 12/24 hour display,

SET button

PLUS (+) button

MINUS (-) button

SUN/MOON button

LARM SET button

34 preset city name

for Sun/moon data

CHANNEL button

MAX/MIN R

button

LARM ON/OFF button

manual time setting, calendar, snooze function, temperature °C or

°F, and weather icon sensitivity setting

•Stop the alarm during alarm ringing

2. PLUS (+) button

•Increase value in all setting modes

•Increase the digits

•Stop the alarm during alarm ringing

3. MINUS (-) button

•Decrease value in all setting modes

•Decrease the digits

•Stop the alarm during alarm ringing

4. SUN/MOON button

•Enter the sun/moon setting mode

•Start the sun/moon time calculation of the selected city

•Stop the alarm during alarm ringing

5. ALARM SET button

•Enter the alarm setting mode

•Stop the alarm during alarm ringing

6. ALARM ON/OFF button

•Activate/de-activate the alarm time

•Stop the alarm during alarm ringing

7. CHANNEL button

•Toggle between the outdoor transmitters 1, 2 and 3 (if more than

one transmitter is used)

•Pressed together with “MAX/MIN R” button for 3 sec allows

temperature channel reset

•Exit any set mode anytime during setting and to return to the

normal display mode

•Stop the alarm during alarm ringing

8. MAX/MIN R button (Max/min Reset)

•Press shortly to toggle between maximum, minimum and current

temperature value for selected outdoor temperature channel.

•Press and hold for 4 seconds to reset the maximum and minimum

records for selected temperature channel.

•Press to activate snooze function during alarm if snooze time is

valid in setting mode.

•Stop the alarm if snooze time is off in setting mode

•Pressed together with the “CHANNEL” button allows temperature

channel reset

B. LCD Screen

The LCD screen is split into 5 sections displaying the information for time

and date, sun/moon data, indoor data, weather forecast and outdoor data.

C. Manual Setting Sequence

The following manual settings can be changed when pressing the “SET”

button:

•LCD contrast setting

•City location setting

Sunset time

Moon icon/Moon

phases icon

Moonset time

Weather tendency

indicator

Time

Date display

Indoor relative

humidity in RH%

Sun icon

City location light

Time reception icon

(for WWVB time)

larm icon

Moonrise time

Sunrise time

Indoor temperature in

°C or ºF

Weather forecast icon

Outdoor data signal

reception indicator Outdoor Temperature in

°C or ºF

Outdoor transmitter

identification number

•Time zone setting

•DST (Daylight Saving Time) setting

•WWVB ON/OFF setting

•12/24-Hour setting

•Manual time setting

•Calendar setting

•Snooze setting

•°C/°F setting

•Weather forecasting icon sensitivity setting

LCD Contrast Setting

The LCD contrast can be set within 8 levels, from LCD 0 to LCD7

(the default setting is LCD 5):

1. Press and hold the “SET” button until the digit starts flashing in the LCD.

2. Press and release the PLUS (+) or MINUS (-) button to view all levels of

contrast.

3. Select the desired LCD contrast.

4. Press and release the “SET” button to confirm and enter in the City location

setting.

City Location Setting

Open the left side panel on the Weather station to see the 45 preset city names list.

Any city can be selected in order to view the sun/moon data (the default city is

Washington D.C.). To select a city:

1. Open the left panel on the weather station. List of cities are displayed.

2. Use the PLUS (+) or MINUS (-) to select a city.

3. A small dot displayed on the left side of the LCD will light up next to the city

name.

Flashing

Last digit flashing

Flashing

4. When a city is selected the city’s time zone will be displayed on the 4-time zone

map located on the right side of the LCD.

5. Press and release the “SET” button to confirm and enter in the Time zone

setting.

For a list of cities please see page 25 please.

Time Zone Setting

The default (factory set) time zone of the indoor weather station is EST –5 (the

default time zone for the default city, Washington D.C.). To set a different time

zone:

1. The current time zone value starts flashing on the LCD.

2. Press and release PLUS (+) or MINUS (-) button to set the time zone.

3. The range runs from 0 to +12 and then runs from -12 back to 0 in consecutive 1-

hour intervals.

4. The LCD also displays a US time zone map and highlights the selected time

zone for –5hr(EST), -6hr(CST), -7hr(MST) and –8hr(PST) zones.

5. Press and release the “SET” button to confirm and enter the DST (Daylight

Saving Time) setting.

DST (Daylight Saving Time) Setting

Note: The DST default is “ON”, meaning that the received time will automatically

be adjusted according to Daylight Saving Time in the spring and fall. For areas that

do not recognize DST changes (Arizona and parts of Indiana) turn the DST “OFF”.

1. The digit “ON” will start flashing on the LCD.

2. Press and release the PLUS (+) or MINUS (-) button to turn OFF the DST

function.

Flashing

Andere Handbücher für WS-9016U

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology WS-9125U-IT-CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7075U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-1611 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009-IT Betriebsanleitung

La Crosse Technology

La Crosse Technology Wireless Weather Station Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9151U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7047TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7078TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology Wireless 433 MHz Temperature Station... Bedienungsanleitung

La Crosse Technology

La Crosse Technology WW85777v2 Installationsanleitung

La Crosse Technology

La Crosse Technology C85845V3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9018U Bedienungsanleitung

La Crosse Technology

La Crosse Technology TX233RW Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-2814U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology C79790 Abmessungen

La Crosse Technology

La Crosse Technology WS-1516-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WA-1340U Bedienungsanleitung

La Crosse Technology

La Crosse Technology KCombo3 WS-9080U-IT WS-9640U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1415BWV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7047TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9009BK-IT Abmessungen

La Crosse Technology

La Crosse Technology WS-7058U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-1425B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WD-3102U Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung