La Crosse Technology WS9132 Bedienungsanleitung

WIRELESS 868 MHz WEATHER STATION

Instruction manual

INTRODUCTION:

Congratulations on purchasing this innovative 868 MHz Weather Station which displays the

weather forecast, time, indoor temperature and up to three outdoor temperature readings.

o enjoy the full benefits of this innovative product, please read this operating manual.

T e Weat er Station

FEATURES:

• DCF Radio controlled time with manual setting option

• ime reception ON/OFF (user selectable)

• 12/24 hour time display

• ime zone option ±12 hours

• Calendar display (day and month)

LCD

Display

Function keys

Battery compartment

Hanging hole

Foldout

Stand

min

• Weather forecasting with weather tendency indicator

• Indoor comfort indicator

• emperature display in ºC/ºF

• Indoor and outdoor temperature display with MIN/MAX records and time of reception

• Indoor humidity display as RH% with MIN/MAX records

• Weather icon sensitivity setting

• LCD contrast selectable

• Can receive up to 3 outdoor temperature transmitters

• Low battery indicator

• able standing or wall mounting

This socket is only for the

external probe. Do not

apply power plug to it.

Optional

external

probe

T e Outdoor Temperature Transmitter

•

Remote transmission of outdoor temperature to

Weather Station by 868 MHz signals

•

Dual channel transmitter*: one internal channel

and one probe channel

•

Shower proof casing

•

Wall mounting and table stand

*DUAL CHANNEL TRANSMITTER -

here is an internal sensor channel and an external probe channel in the transmitter.

Once the transmitter is successfully recognized by the Weather station, Channel 1 of the

Weather station will display the temperature data measured by internal sensor and Channel

2 will display the temperature estimated by the probe.

If the measuring probe is unplugged, the "probe channel" on Weather station (Channel 2)

will show "---", yet the data from the internal sensor will still be shown on Channel 1 .

he probe can be connected to the remote temperature transmitter anytime after initial

setup. here is no need to reset the units, should the probe be unplugged or re-plugged

again. he Weather station will automatically detect the temperature probe data and will

display the temperature data on Channel 2 after the probe is plugged.

SETTING UP:

W en one transmitter is used:

1. First, insert the batteries into the transmitter (see “Install and replace batteries in

t e Temperature transmitter” below).

2. Within 30 seconds of powering up the transmitter, insert the batteries to the Weather

Station (see “Install and replace batteries in t e Weat er Station” below). Once

the batteries are in place, all segments of the LCD will light up briefly. hen the

indoor temperature and the time as 0:00 will be displayed. If they are not shown on

LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before

reinserting them. Once the indoor data is displayed, user may proceed to the next

step.

3. After the batteries are inserted, the Weather Station will start receiving data signal

from the transmitter.

4. If the optional probe has been plugged to the dual channel transmitter, the outdoor

temperature should then be displayed on the Weather Station on channel 1 and 2.

Also, the signal reception icon will be displayed. If this does not happen after 2

minutes, the batteries will need to be removed from both units and reset from step 1.

Note:

Channel 1 will show the reading from the internal sensor of the dual channel transmitter;

Channel 2 will show the reading sensed by the probe. If the probe is not plugged to the

transmitter, " - -" will be shown on Channel 2.

5. In order to ensure sufficient 868 MHz transmission, the final position between the

Weather Station and the transmitter should not be more than 100 meters (see notes

on “Positioning” and “868 MHz Reception”).

6. Once the remote temperature has been received and displayed on the Weather

Station, the DCF time code reception is automatically started. his takes typically

between 3-5 minutes in good conditions—but may take up to 4 nights.

W en two transmitters are used

1. User shall remove all the batteries from the Weather Station and transmitters and wait

60 seconds (if setting has been done with one transmitter before).

2. Insert the batteries into the first transmitter.

3. Within 30 seconds of powering up the first transmitter, insert the batteries into the

Weather Station. Once the batteries are in place, all segments of the LCD will light up

briefly. hen the indoor temperature and the time as 0:00 will be displayed. If they are

not shown on the LCD after 60 seconds, remove the batteries and wait for at least 60

seconds before reinserting them.

4. he outdoor temperature readings from the first transmitter (Channel 1 and 2) should

then be displayed on the Weather Station (if probe sensor has been installed onto the

first transmitter). If this does not happen after 2 minutes, the batteries will need to be

removed from both units and reset from step 1.

5. Insert the batteries into the second transmitter as soon as the outdoor temperatures

from the first transmitter are displayed on the Weather Station.

Note: User must insert the batteries into the second transmitter within 20 seconds of

reception of the first transmitter.

6. he outdoor temperature reading from the second transmitter will be shown on the

LCD and the Channel No. will shift back to "1", indicating that all three channels are

running successfully. If this does not happen after 2 minutes, the batteries will need to

be removed from all the units and reset from step 1.

Note: After the Weather Station has successfully received the second transmitter, Channel 3

will display the data measured by the internal sensor of the second dual channel transmitter.

Yet the probe data from the second transmitter will not be displayed on the Weather Station.

7. Once the remote temperature has been received and displayed on the Weather

Station, the DCF time code reception is automatically started. his takes typically

between 3-5 minutes in good conditions.

IMPORTANT:

•

ransmission problems will arise if the setting for additional transmitters is not

followed as described above. Should transmission problems occur, it is necessary to

remove the batteries from all units and follow the set-up from step 1.

•

If after 10 minutes, the Atomic auto-set time (DCF time) has not been received, press

the SE key to manually enter a time initially.

•

Daily DCF reception is done at 02:00 and 03:00. If the reception at 03:00 is not

successful, then at 04:00 and 05:00 and 06:00 there are other tries, until one is

successful. If the reception at 06:00 is still not successful, then the next try takes place

at 02:00 next day. (Please refer also to notes on “DCF-77 Radio Controlled Time”

and “Manual Time Setting”).

INSTALL AND REPLACE BATTERIES IN THE WEATHER STATION

he Weather Station uses 2 x AA, IEC LR6, 1.5V batteries. o install and replace the

batteries, please follow the steps below:

1. Insert finger or other solid object in the space at the

bottom center of the battery compartment and lift up to

remove the cover.

2. Insert batteries observing the correct polarity (see

marking).

3. Replace compartment cover.

INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER

he temperature transmitter uses 2 x AAA, IEC LR3, 1.5V battery. o install and replace the

batteries, please follow the steps below:

1. Remove the battery compartment cover.

2. Insert the batteries, observing the correct polarity (see marking).

Replace the battery compartment cover.

Note:

In the event of changing batteries in any of the units, all units need to be reset by following

the setting up procedures. his is because a random security code is

assigned by the

transmitter at start-up and this code must be received and stored by the Weather Station in

the first 3 minutes of power being supplied to it

Inhaltsverzeichnis

Andere La Crosse Technology Wetterstation Handbücher

La Crosse Technology

La Crosse Technology 308-1409BTV2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-913 3U-IT-CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology V10-TH Abmessungen

La Crosse Technology

La Crosse Technology C84612 Betriebsanleitung

La Crosse Technology

La Crosse Technology WS-9125U-IT-CA Bedienungsanleitung

La Crosse Technology

La Crosse Technology CA79103v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 308-179OR Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7220U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9035U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C85845 Bedienungs- und Wartungshandbuch

La Crosse Technology

La Crosse Technology 724-1415BL Abmessungen

La Crosse Technology

La Crosse Technology WS-9611U-IT Bedienungsanleitung

La Crosse Technology

La Crosse Technology SW403 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS6828 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9016TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology 327-1414Wv2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Tomorrow's Weather Today TX24U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9160UV2 Abmessungen

La Crosse Technology

La Crosse Technology 308-1415 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Weather Direct WD-3308 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-7212U Bedienungsanleitung

La Crosse Technology

La Crosse Technology T85647 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9004U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-9626U-IT Bedienungsanleitung

Beliebte Wetterstation Handbücher anderer Marken

Auriol

Auriol AHFL 433 A1 Bedienungsanleitung

Hyundai

Hyundai WS 2202 Bedienungsanleitung

NexSens

NexSens G2-HYDROMET Bedienungsanleitung

IROX

IROX HBVR761 UV-X Bedienungsanleitung

ADE

ADE WS 1711 Bedienungsanleitung

Auriol

Auriol z29592 Bedienungsanleitung

Auriol

Auriol 296289 Bedienungsanleitung

Hyundai

Hyundai WS 2266 Bedienungsanleitung

Ventus

Ventus W177 Bedienungsanleitung

National Geographic

National Geographic VA Colour RC Bedienungsanleitung

Levenhuk

Levenhuk Discovery Report WA40 Bedienungsanleitung

Instant Transmission

Instant Transmission MA 10410 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PHB-318 Bedienungsanleitung

WAREMA

WAREMA EWFS Weather station eco Bedienungsanleitung

TFA

TFA 30.3013.IT Bedienungsanleitung

Oregon Scientific

Oregon Scientific RMR966PA Bedienungsanleitung

Alecto

Alecto WS-1200 Bedienungsanleitung

Oregon Scientific

Oregon Scientific Alizé BAR266 Bedienungsanleitung