Lanner FW-7580 Bedienungsanleitung

Network

Application Platforms

Hardware platforms for next generation networking infrastructure

FW-7580

User's Manual

Publication date:2010-04-15

About

Network Application Platforms

Overview

Icon Descriptions

The icons are used in the manual to serve as an indication

of interest topics or important messages. Below is a

description of these icons:

NOTE: This check mark indicates that

there is a note of interest and is something

that you should pay special attention to

while using the product.

WARNING: This exclamation point

indicates that there is a caution or

warning and it is something that could

damage your property or product.

Online Resources

The listed websites are links to the on-line product

information and technical support.

Resource Website

Lanner http://www.lannerinc.com

Product Resources http://assist.lannerinc.com

RMA http://eRMA.lannerinc.com

reserved. The original manufacturer reserves the right to

make improvements to the products described in this

manual at any time without notice.

No part of this manual may be reproduced, copied,

translated or transmitted in any form or by any means

without the prior written permission of the original

manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original

manufacturer assumes no responsibility for its use, nor for

any infringements upon the rights of third parties that

may result from such use.

Acknowledgement

Intel, Pentium and Celeron are registered trademarks of

Intel Corp.

Microsoft Windows and MS-DOS are registered trademarks

of Microsoft Corp.

All other product names or trademarks are properties of

their respective owners.

Compliances

This product has passed the CE test for environmental

specifications. Test conditions for passing included the

equipment being operated within an industrial enclosure.

In order to protect the product from being damaged by

ESD (Electrostatic Discharge) and EMI leakage, we strongly

recommend the use of CE-compliant industrial enclosure

products.

FCC Class A

This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required

to correct the interference at his own expense.

TTaTTable of Contentsbeable of Contents

Chapter 1: Introduction 1

System Specication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Front Panel Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rear Panel Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2: Hardware Setup 5

Preparing the Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the System Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the Hard Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing a CompactFlash Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CPU and the Heat Sink Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Riser Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Chapter 3: Motherboard Information 8

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Chapter 4: BIOS Settings 12

Updating the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Accessing the BIOS menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Navigating the BIOS menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

The Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Boot Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Exit Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Appendix A: Programming Watchdog Timer 36

Appendix B: Setting up Console Redirections 37

Appendix C: Digital Input/Output Control on the GPIO port 38

Appendix D: Programming LAN Bypass 39

Introduction

Chapter 1

Network Application Platforms

Chapter 1:

Introduction

Thank you for choosing the FW-7580. The Fw-7580 is a 1U

network communication appliance that is designed to

meet your demand for high quality network application

platform with its high port density. The FW-7580 comes

with 1 FE and 6 Gb Ethernet ports with one pair capable

to be an abnormal state packet bypass.

This network appliance is an ideal platform for applications

such as load balancing and UTM management.

Please refer to the following chart below for a summary of

the system’s specifications.

System Specification

FEATURES DESCRIPTION

Form Factor 1U Rackmount

Platform

Processor

Supports Intel Core 2 Duo,

Pentium D, Celeron proces-

sors, LGA 775

Chipset Intel G41 + ICH7R

Front Side Bus 1333/1066/800 MHz

Max Speed 3.0 GHz

System Memory

Technology Dual-channel DDR2

800/667 MHz

Max Capacity 8GB

Socket 240P DIMM x 2

OS Support Windows, Linux, OpenBSD,

FreeBSD

Storage

HDD Bay(s) 2.5” x 1

Storage Interface Serial ATA x 2

CompactFlash (type II) x 1

Networking

Ethernet Port Density

7 onboard (RJ45 x 7)

1 pair support by-pass

function

Controller Intel 82574L GbE x 6,

Intel 82562ET FE x 1

I/O Interface

Console RJ45 x 1

USB 2.0 2

Expansion* PCI-E (x)8 x 1

Cooling

Processor 1U CPU passive heatsink

with duct to 2 fans

System Cooling fan x 1 with Smart

Fan

Environmental

Parameters

Temperature, ambient

operating / storage 0ºC ~40ºC / -20ºC~60ºC

Humidity (RH), ambient op-

erating and non-operating 5 ~ 95%, non condensing

Miscellaneous

LCD Module 2 x 20 character

Watchdog Yes

Internal RTC with Li Battery Yes

Physical

Dimensions

Dimensions (WxHxD) 431x44.4x276 mm

(17x1.7x10.9 in)

Weight 7 kg (15.4 lbs)

Power

Type / Watts 1U ATX SPS / 220W

Input AC 100~240V@50~60Hz

Output +3.3V 16.8A, +5V 12A, +12V

10A, -12V 0.8A, +5VSB 2A

Approvals &

Compliance

CE Emission, FCC Class

A, RoHS

Introduction

Chapter 1

Network Application Platforms

Package Contents

Your package contains the following items:

FW-7580 Network Security Platform•

Power cable•

1 crossover Ethernet cable (1.8 meter)•

1 straight-through Ethernet cable (1.8 meter)•

1 RJ-45 to DB-9 female console cable•

Serial-ATA hard drive cable•

1 threaded-screw set•

1 ear bracket set•

Drivers and user’s manual CD.•

Introduction

Chapter 1

Network Application Platforms

F1 Power/Status/HDD LED

Power: If the LED is on it indicates that the system is powered on. If it is off, it indicates that the system is powered off.

Status: If the LED is green, it indicates that the system’s operational state is normal. If it is red, it indicates that the system is

malfunctioning.

HDD: If the LED is on, it indicates that the system’s storage is functional. If the LED blinks, it indicates data access activities.

If it is off, it indicates that there is no hard disk present or functional.

F2 System Panel: LCD System Panel

The LCD System Panel can be programmed to display operating status and configuration information. For more details or

sample programming code, please refer to Appendix B Programming the LCM.

F3 Reset Switch

The reset switch can be used to reboot the system without turning off the power.

F4 Console Port

By using suitable rollover cable or RJ-45 to DB-9 Female (Cisco console cable), you can connect to a computer terminal for

diagnostic or configuration purpose. Terminal Configuration Parameters: 115200 baud, 8 data bits, no parity, 1 stop bit , no

flow control.

F5 Two USB 2.0 Ports

It connects to any USB devices; for example, a flash drive.

F6 Management Port

This FastEthernet port can be connected for configuration or troubleshooting purpose. Or it can be used as a WAN port.

6 Gigabit LAN ports

Left LED:If the LED is green, it indicates that the connection speed is 100Mbps. If the LED is orange, it indicates that it

indicates that the connection speed is 1000Mbps.

Right LED: If the LED is on, it indicates that the port is active. If it blinks, it indicates there is traffic.

Using suitable RJ-45 cable, you can connect FW-7580 System to a computer, or to any other piece of equipment that has

an Ethernet connection; for example, a hub or a switch. Moreover, 1 pair (LAN5-LAN6) can be configured as LAN Bypass

when failure events occur. This feature is implemented in hardware using watch dog timer functionality. Refer to Appendix

D Programming Lan Bypass for a sample implementation of this feature.

Note:

The number of LAN ports varies depending on the model.1.

The availability of LAN Bypass varies depending on the model.2.

Manage LAN1 LAN2 LAN3 LAN4 LAN5 LAN6

F3 F4 F5

F1 F2

Front Panel Features

Introduction

Chapter 1

Network Application Platforms

Rear Panel Features

R3R1 R2 R4 R5 R6 R7

R1 AC Power-in socket: A 100/240VAC Switching Single Power Supply.

R2 Power-on Switch: A switch to turn on or off the power.

R3 Chassis Fans 1, 2 and 3

R4 VGA Port: A VGA connector for connecting the monitor.*

R5 RS-232 Serial Port: It can be connected to a terminal computer for diagnostic purpose.*

R6 USB2.0 Port: It connects to any USB devices; for example, a flash drive.*

R7 Low profile PCI-E slot: A slot for connecting the extended PCI-E card

The slot is for installing an additional adapter card which is connected to the main board via a riser card.

Note: The ports marked with * are optional.

Introduction

Chapter 2

Network Application Platforms

Chapter 2:

Hardware Setup

Preparing the Hardware Installation

To access some components and perform certain service

procedures, you must perform the following procedures

first.

WARNING: To reduce the risk of personal injury,

electric shock, or damage to the equipment,

remove the power cord to remove power from the

server. The front panel Power On/Standby button

does not completely shut off system power.

Portions of the power supply and some internal

circuitry remain active until AC power is removed.

Unpower the FW-7580 and remove the power cord.1.

Unscrew the 3 threaded screws from the top cover of2.

the FW-7580 System.

Slide the cover backwards and open the cover3.

upwards.

Installing the System Memory

The motherboard supports DDR2 memory that features

data transfer rates of 667 and 800 MHz to meet the higher

bandwidth requirements of the latest operating system

and Internet applications. It comes with two Double

Data Rate(DDR2) Dual Inline Memory Modules (DIMM)

sockets.

Open the DIMM slot latches.1.

Install the DIMM.2.

Note:

All DIMMs installed must be the same speed1.

(DDR2 667 or 800). Do not install DIMMs

supporting different speeds.

The motherboards can support up to 8 GB2.

memory capacity in maximum. However, due

to the memory address limitation on 32-bit

Windows OS, when you install 4GB or more

memory on the motherboard, the actual usable

memory for the OS can be about 3GB or less. For

effective use of memory, we recommend that you

do any of the following:

Use a maximum of 3GB system memory if you are

using a 32-bit Windows OS.

Install a 64-bit Windows OS when you want to

install 4GB or more on the motherboard.

For more details, refer to the Microsoft© support

site.

Installing the Hard Disk

The system can accomdate two Serial-ATA disks. Follow

these steps to install a hard disk into the FW-7580:

Unsrew the 4 screws on the hard disk tray to take out1.

the hard disk tray from the system.

Place hard disk on the hard disk tray and align the holes2.

of the hard disk with the mounting holes on the tray.

Secure the hard disk with 4 mounting screws on the3.

hard disk tray.

Connect the Serial-ATA power and hard disk cables to4.

the hard disk’s connectors respectively.

Plug the Serial-ATA cable to the Serial-ATA Connector5.

on the main board.

Repeat steps 2 to 5 to install a second disk (if there is6.

one).

Put the hard disk tray with the installed hard disk back7.

to the system and secure it with the mounting screws.

Introduction

Chapter 2

Network Application Platforms

Remove the CPU socket cap.1.

Press the load lever and release it from the retention2.

tab.

Lift the load lever and then the plate.3.

Align the cut-out of the CPU and the notch on the4.

socket. The CPU should fit perfectly into the socket.

Note that the CPU fits in the socket in only one

direction.

Close the plate and push the load lever to lock it back5.

to the retention tab.

Peel off the sticker on the CPU to expose the thermal6.

compound.

Put the heat sink on top of the installed CPU, match7.

the screws with the screw holes on the board. Fasten

two screws which are opposite to each other at a time

and then the other two. It is easier this way because of

the springiness of the bracket.

Place the heat sink cover on top of the installed heat8.

sink and screw the two screws to fasten it on the case.

Note:

The CPU heat sink could only be installed in only1.

one direction as shown in the picture.

To protect the CPU socket pins, retain the CPU2.

cap when the CPU is not installed.

Installing a CompactFlash Card

FW-7580 provides one CompactFlash slot(CF1). Follow the

procedures bellow for installing a CompactFlash card.

Align CompactFlash card and the card slot with the1.

arrow pointing toward the connector.

Push the card to insert into the connector.2.

Note: The Compact Flash Card has a jumper

setting (J2) to set itself as a primary or slave device It is

only useful when there are other storage devices such as

a CD-ROM installed in the system which is not applicable

in the FW-7580. For more details, please refer to Chapter 3

Motherboard Information.

CPU and the Heat Sink Installation

The FW-7580 sever system is powered by the MB-75807580

sever board, which comes with one ZIF type LGA775 CPU

socket.

Follow the procedures bellow for installing a CPU

Introduction

Chapter 2

Network Application Platforms

Riser Card Installation

To provide a PCI-E connector for installing an additional

adaptor in a compact system lke the FW-7580, a riser card

has to be installed.

Align the riser card with the PCI-E golden finger1.

connector.

Insert the card into the connector firmly.2.

Fasten the screws to fix the card to the board.3.

Inhaltsverzeichnis

Andere Lanner Netzwerk-Hardware Handbücher

Lanner

Lanner EAI-I130 Bedienungsanleitung

Lanner

Lanner ECA-4027 Bedienungsanleitung

Lanner

Lanner NCA-4030 Bedienungsanleitung

Lanner

Lanner HTCA-6400 Bedienungsanleitung

Lanner

Lanner NCA-6520 Bedienungsanleitung

Lanner

Lanner NCA-5540 Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Lanner

Lanner NCA-1040SE Bedienungsanleitung

Lanner

Lanner FX-3230 Bedienungsanleitung

Lanner

Lanner IIOT-I530 Bedienungsanleitung

Lanner

Lanner NCA-2512 Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Lanner

Lanner NCA-1513 Bedienungsanleitung

Lanner

Lanner ECA-4025 Bedienungsanleitung

Lanner

Lanner NCA-1515 Bedienungsanleitung

Lanner

Lanner R6S Bedienungsanleitung

Lanner

Lanner HCP-72i1 Bedienungsanleitung

Lanner

Lanner NCA-2523 Bedienungsanleitung

Lanner

Lanner uCPE NCA-4020 Bedienungsanleitung

Lanner

Lanner NCA-1611A Bedienungsanleitung

Lanner

Lanner NCA-4220 Bedienungsanleitung

Lanner

Lanner FW-7551 Bedienungsanleitung

Lanner

Lanner FW-8756 Bedienungsanleitung

Lanner

Lanner NCA-5230 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung

Cantek

Cantek NR310-4 Bedienungsanleitung