Lantronix WiPort Kurzanleitung zur Einrichtung

WiPort™ Integration Guide

Part Number 900-333

Revision G June 2006

be transmitted or reproduced in any form or by any means without the written

permission of Lantronix. Printed in the United States of America.

WiPort, with its patent-pending technology, is a trademark of Lantronix.

Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of

The Open Group. Windows 95, Windows 98, Windows 2000, Windows NT, and

Windows XP are trademarks of Microsoft Corp. Netscape is a trademark of Netscape

Communications Corporation.

Contacts

Lantronix Corporate Headquarters

15353 Barranca Parkway

Irvine, CA 92618, USA

Phone:949-453-3990

Fax: 949-453-3995

Technical Support

Phone: 800-422-7044 or 949-453-7198

Fax: 949-450-7226

Online: www.lantronix.com/support

Email [email protected]

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix

web site at www.lantronix.com/about/contact/

WiPort™ Integration Guide 3

Disclaimer

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

This device is intended only for OEM Integrators. The OEM integrator should be

aware of the following important issues.

Labeling of the End Product

The end product to integrate this module has to be clearly identified on the label that

this end product contains an FCC approved RF module. The format of such

statement could be "Contains Transmitter with FCC ID: R68WIPORTG" or similar.

Integration Note

a) This module is authorized under limited module approval specified to mobile host

equipment. So, the antenna must be installed such that 20cm is maintained between

the antenna and users.

b) The transmitter module may not be co-located with any other transmitter or

antenna.

As long as the 2 conditions above are met, further transmitter testing will not be

required. However, the OEM integrator is still responsible for testing their end-product

for any additional compliance requirements required with this module installed (for

example, digital device emission, PC peripheral requirements, etc.)

Note: In the event that these conditions can not be met (for example certain

laptop configurations, general purpose PCMCIA or similar cards, or co-

location with another transmitter), then the FCC authorization is no longer

considered valid and the FCC ID can not be used on the final product

(including the transmitter) and obtaining a separate FCC authorization.

Note: Changes or modifications to this device not explicitly approved by Lantronix will

void the user's authority to operate this device.

WiPort™IntegrationGuide 4

Contents

1: Introduction 6

About the Integration Guide________________________________________________6

Additional Documentation _________________________________________________6

2: Description and Specifications 7

WiPort Overview ________________________________________________________7

WiPort Block Diagram ____________________________________________________8

PCB Interface __________________________________________________________9

Mating Connector ______________________________________________________10

Serial Input/Output______________________________________________________10

Sample Layouts for RS-485 Connectivity ____________________________________12

WLAN Input/Output _____________________________________________________13

Ethernet Input/Output ___________________________________________________13

Power, Ground, and Reset _______________________________________________14

Absolute Maximum Ratings_______________________________________________14

Recommended Operating Conditions _______________________________________14

Ethernet PHY Receiver Input Characteristics (RX+, RX-) ________________________15

100Base-TX Transceiver Characteristics (TX+, TX-) ___________________________15

Wireless Specifications __________________________________________________15

Technical Specifications _________________________________________________17

Dimensions ___________________________________________________________18

Recommended PCB Layout ______________________________________________19

Product Information Label ________________________________________________20

3: Development Kit 21

Contents of the Kit ______________________________________________________21

Evaluation Board Description _____________________________________________21

Serial Interfaces________________________________________________________21

Power Supply _________________________________________________________22

General Control PLD ____________________________________________________22

Configuration Switch Bank _______________________________________________22

Evaluation Board Layout _________________________________________________23

Evaluation Board Schematics _____________________________________________24

Compliance Information__________________________________________________28

Warranty _____________________________________________________________29

WiPort™ Integration Guide 5

List of Figures

Figure 2-1. WiPort Block Diagram...........................................................................................8

Figure 2-2. Combined RS-232/485 Transceiver ...................................................................12

Figure 2-3. Separate RS-232/485 Transceivers ...................................................................12

Figure 2-4. Separate RS-485 Transceivers for 2-Wire and 4-Wire Setups...........................13

Figure 2-5. Side Views..........................................................................................................18

Figure 2-6. Top View.............................................................................................................18

Figure 2-7. Bottom View........................................................................................................19

Figure 2-8. PCB Layout.........................................................................................................19

Figure 2-9. Product Label......................................................................................................20

Figure 3-1. WiPort Evaluation Board Layout.........................................................................23

Figure 3-2. Evaluation Board Schematics.............................................................................24

List of Tables

Table 2-1. PCB Interface Signals............................................................................................9

Table 2-2. Mating Connectors...............................................................................................10

Table 2-3. Channel 1 Connections........................................................................................11

Table 2-4. Channel 2 Connections........................................................................................11

Table 2-5. Channel 2 RS-422/485 4-Wire Connections........................................................11

Table 2-6. Channel 2 RS-485 2-Wire Connections...............................................................11

Table 2-7. WLAN Signals......................................................................................................13

Table 2-8. Ethernet Signals...................................................................................................13

Table 2-9. Power, Ground, and Reset Pins ..........................................................................14

Table 2-10. Absolute Maximum Ratings ...............................................................................14

Table 2-11. Operating Conditions, Serial Ports, & Configurable Pins...................................14

Table 2-12. Ethernet Input Characteristics............................................................................15

Table 2-13. 100Base-TX Transceiver Attributes ...................................................................15

Table 2-14. Wireless Specifications......................................................................................15

Table 2-15. Technical Specifications ....................................................................................17

Table 3-1. RS-232 Signals....................................................................................................22

Table 3-2. Channel 2 RS-485 4-Wire Connector ..................................................................22

Table 3-3. Channel 2 RS-485 2-Wire Connector ..................................................................22

Table 3-4. Jumper Configurations.........................................................................................22

Table 3-5. Configurable Pin Configurations ..........................................................................23

WiPort™IntegrationGuide 6

About the Integration Guide

This guide provides the information needed to integrate the WiPort device server

within another product. The intended audiences are the engineers responsible for

integrating the WiPort into their product.

Additional Documentation

The following guides are available on the product CD and the Lantronix Web site

(www.lantronix.com)

WiPort™ Development Kit

Quick Start Guide

Briefly explains the basics to get the WiPort up

and running.

WiPort™ User Guide Provides information needed to configure, use,

and update the WiPort firmware.

WiPort™IntegrationGuide 7

The WiPort wireless embedded device server is a complete network-enabling

solution based on the IEEE 802.11b/g wireless standard, with WPA and WEP

capabilities. WiPort allows Original Equipment Manufacturers (OEMs) to add

wireless connectivity to their products by incorporating it onto a circuit board with

minimal engineering.

The WiPort functions independently of a PC, providing an integrated solution that

combines a processor, memory, 802.11b/g transceiver and dual high-speed serial

ports into a single compact module. It includes a wireless connection, an operating

system, an embedded Web server, and a full TCP/IP protocol stack. In addition, the

WiPort sends email alerts and supports numerous other network communication

protocols, including ARP, UDP, TCP, ICMP, Telnet, AutoIP, DHCP, HTTP and

SNMP.

WiPort Overview

The WiPort contains Lantronix’s own DSTni controller with 256 Kbytes of internal

zero wait state SRAM, 16 Kbytes of boot ROM, and integrated 10/100 PHY.

The WiPort also contains the following:

 Two 3.3-volt v24 serial interfaces (5V tolerant)

 Up to 921600 Baud

 16 or 32Mbit flash memory (with optional additional 8Mbit SRAM)

 88 MHz clock

 802.11b interface

 11 configurable pins

 10/100 Ethernet interface

The WiPort requires +3.3-volt power and is designed to operate within a temperature

range of -30ºC to +70ºC.

Description and Specifications

WiPort™ Integration Guide 8

WiPort Block Diagram

The following drawing is a block diagram of the WiPort showing the relationships of

the components.

Figure 2-1. WiPort Block Diagram

Description and Specifications

WiPort™ Integration Guide 9

PCB Interface

Table 2-1. PCB Interface Signals

Pin Number WiPort Pin

Function

Notes

1 3.3V Power Supply input

2 3.3V Power Supply input

3 RTS0 Request “to send” hardware

flow control output (logic

level), serial port 0

4 TXD0 Transmit data output (logic

level), serial port 0

5 RXD0 Receive data input (logic

level), serial port 0

6 CP2 Configurable pin

7 CP3 Configurable pin.

8 CTS0 Clear “to send” hardware flow

control input (logic level),

serial port 0

9 CP10 Configurable pin

10 CP8 Configurable pin

11 Signal Ground

12 Signal Ground

13 Reset In Resets the WiPort unit. Reset

In is low active. Minimum

reset pulse width is 2ms at IIL

= -500 µA

14 CP0 Configurable pin

15 RTS1 Request “to send” hardware

flow control output (logic

level), serial port 1

16 TXD1 Transmit data output (logic

level), serial port 1

17 RXD1 Receive data input (logic

level), serial port 1

18 CP9 Configurable pin

19 CP4 Configurable pin

20 CTS1 Clear “to send” hardware flow

control input (logic level),

serial port 1

21 Reserved Reserved for future use

22 Reserved Reserved for future use

23 Signal Ground

24 Signal Ground

25 Reserved Reserved for future use

26 Reserved Reserved for future use

27 Ethernet Status

LED2

Ethernet activity

28 Ethernet Status

LED1

Ethernet link

29 Ethernet TX- Output

30 Ethernet TX+ Output

Description and Specifications

WiPort™ Integration Guide 10

Pin Number WiPort Pin

Function

Notes

31 Ethernet RX Center

Tap

32 Ethernet TX Center

Tap

33 Ethernet RX- Input

34 Ethernet RX+ Input

35 CP1 Configurable pin

36 WLAN Power LED

(WiPort B only)

High active output, tristated in

Ethernet mode

37 CP6 Configurable pin

38 CP5 Configurable pin.

39 WLAN Activity LED High active output, tristated in

Ethernet mode

40 CP7 Configurable pin

Note: For all the configurable pins, see the WiPort User Guide for selectable

functions.

Mating Connector

Table 2-2. Mating Connectors

Mating Connector Description

Recommended: Samtec FTMH-120-03-F-DV-ES (shrouded

header)

Alternative: Samtec FTMH-120-03-F-DV (not shrouded)

Alternative: Oupiin 2411-2X20GDN/017 (not shrouded)

The mating connector is

a 1mm micro header,

40 pins,

2 x 20.

Serial Input/Output

The unit has two serial ports compatible with V24 serial standards at data rates up to

921Kbps. The serial I/O signals are 3.3V CMOS logic level and pins are 5V tolerant.

Serial signals connect to an internal device, such as a UART. For evaluation and

prototype work, it is convenient to have an external RS-232 interface that can

connect to the serial port on a PC. The WiPort Evaluation Board has one RS-232

and one RS-232/422/485 transceiver (level shifters) to implement this external

interface (only the WiPort 485 supports the RS-422/485 interface).

If desired, use the CPs to create a DTE or DCE-style interface using any 3 available

CPs. To create these interfaces, connect the signals according to Table 2-3 and

Table 2-4.

Note: CPx, CPy, and CPz are any of the available CPs.

Andere Handbücher für WiPort

Inhaltsverzeichnis

Andere Lantronix Server Handbücher

Lantronix

Lantronix xPico Bedienungsanleitung

Lantronix

Lantronix CoBox E2 01 Bedienungsanleitung

Lantronix

Lantronix MSS Bedienungsanleitung

Lantronix

Lantronix MatchPort b/g Pro Installationshandbuch

Lantronix

Lantronix WiBox Bedienungsanleitung

Lantronix

Lantronix XPress-DR Plus Bedienungsanleitung

Lantronix

Lantronix EDS4100 Bedienungsanleitung

Lantronix

Lantronix EDS3000PR Bedienungsanleitung

Lantronix

Lantronix EDS-MD Series Bedienungsanleitung

Lantronix

Lantronix Device Server MSS 485 Bedienungsanleitung

Lantronix

Lantronix MSS1-T Bedienungsanleitung

Lantronix

Lantronix XPress DR Bedienungsanleitung

Lantronix

Lantronix SLC8 Bedienungsanleitung

Lantronix

Lantronix XPort Bedienungsanleitung

Lantronix

Lantronix XPress DR+ Bedienungsanleitung

Lantronix

Lantronix xDirect Bedienungsanleitung

Lantronix

Lantronix SLM Bedienungsanleitung

Lantronix

Lantronix MatchPort AR Kurzanleitung zur Einrichtung

Lantronix

Lantronix Device Installer Bedienungsanleitung

Lantronix

Lantronix MSS100 Bedienungsanleitung

Lantronix

Lantronix Micro125 Bedienungsanleitung

Lantronix

Lantronix SLC8 Bedienungsanleitung

Lantronix

Lantronix SCS100 Bedienungsanleitung

Lantronix

Lantronix xport pro Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung