Larson Electronics EPL-SL-4-50X-50LED-RT-MBC-EPP Bedienungsanleitung

EPL-SL-4-50X-50LED-

RT-MBC-EPP

INSTRUCTION MANUAL

200W Explosion Proof LED String Light - (4)

50W Fixtures Daisy Chained - Adjustable

Magnetic Mount

Instruction Manual

Thank you for your purchase of the EPL-SL-4-50X-50LED-RT-MBC-EPP from Larson Electronics.

WARNING

Standard Warning (General)

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

Standard Warnings (LIGHTS)

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EPL-SL-4-50X-50LED-RT-MBC-EPP MUST BE WIRED INACCORDANCE WITH

NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING ISREQUIRED

FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT ANELECTRICIAN. THERE ARE NOSERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK – DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY – FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN – ALLOW FIXTURE TO COOL BEFORE SERVICING.

Larson Electronics, LLC Phone: 877-348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 1 of 3

EPL-SL-4-50X-50LED-RT-MBC-EPP

Explosion Proof Warnings (General)

WARNING

TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL

APPLICABLE ELECTRICAL CODES.

TO AVOID ELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING

CONDUCTOR.

Larson Electronics, LLC Phone: 877-348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 2of 3

EPL-SL-4-50X-50LED-RT-MBC-EPP

TO AVOIDEXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

Magnetic Warning

•PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE.

ELECTROMAGNETIC FIELDS IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE

PACEMAKER INTERFERENCE OR PACEMAKER FAILURE.

•KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR.

Exp Cord Cap

Position device near work area for operation. Run cable to nearby power

source. Insert and twist-lock explosion-proof plug into a compatible receptacle

within the hazardous environment. See plug operation below.

PLUG OPERATION

Electrical connection between plug and compatible receptacle is accomplished

after plug fully inserts into receptacle and rotated clockwise.

1. Lift receptacle door and locate polarization on mating plug pin and

receptacle face. Insert plug straight all the way into receptacle until it

cannot go further.

2. Rotate plug clockwise limit (37º), this closes internal contacts and

completes circuit. This also mechanically locks plug into receptacle so it

cannot be pulled out.

3. To remove plug, push plug inward and turn to counterclockwise, pull plug

straight out.

MOUNTING

Each explosion proof LED light features an adjustable swivel bracket constructed of 3/8" aluminum.

This aluminum mounting bracket has three 200 lb grip magnetic bases which provide a total of 600 lb

of grip and allows operators to mount the unit to ceilings, walls and any flat metallic surfaces. Users

simply attach the magnetic mounting bracket to the desired surface, then hang the lamp assembly from

the bracket.

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

Larson Electronics, LLC Phone: 877-348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 3of 3

EPL-SL-4-50X-50LED-RT-MBC-EPP

To replace driver, disconnect power running to fixture. Dismount fixture and remove the back

cover. Disconnect bad driver and remove the single screw holding it in place. Place new driver

and replace screw. Connect power cord and route wires as needed. Replace back cover plate.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPL-SL-4-50X-50LED-RT-MBC-EPP is designed to provide years of reliable performance. Should the need for

replacement parts arise, please contact Larson Electronics.

1. Perform visual,mechanical and electrical inspections on a regular basis.We recommend routine

checks to be made on a yearly basis. Frequency of use and environment shoulddetermine this. It

is recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA

70B: Recommendedpractice for Electrical Equipment.

2. The lens should be cleaned periodically as neededto ensure continued photometric performance.

Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e.excessivedust build-up). Clean with a non-abrasive clothif needed.

4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics EXP-EMG-2L-LE6 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-LB-50LED-RT-180B Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-FL1524-25-1523 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-AMB-150LED-50-140DB Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-150LED-RT-SP0010-200C Series Bedienungsanleitung

Larson Electronics

Larson Electronics LED10W-1X4LT Bedienungsanleitung

Larson Electronics

Larson Electronics SLEDB-110V-MS Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-DL-12-25-1523 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-48-33W-LED-1227-70C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-FL26-LED Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Bedienungsanleitung

Larson Electronics

Larson Electronics HID-35-RC-W Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-48-100LED-AMB Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-TL-3XTL-C-SOL-100C Bedienungsanleitung

Larson Electronics

Larson Electronics IND-DHA-FUVC-EX-48-3L-V2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPP-3P4W-30A-N7 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-SL-10-20X-LED Bedienungsanleitung

Larson Electronics

Larson Electronics IND-LP-SS-24-2X2-2L-UVC Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-50W-120x12-50 Bedienungsanleitung

Larson Electronics

Larson Electronics LEDWP-600E-M-E2E Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-120-150-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-EB Bedienungsanleitung

Larson Electronics

Larson Electronics IND-RL-HDB-BX9-120V Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung