Larson Electronics HALP-24-2L-LED-2XH Bedienungsanleitung

HALP-24-2L-LED-2XH

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Class I, Division 2 LED Light - 2 foot, 2 lamp - Corrosion Resistant Construction

(Saltwater) - 2 Input and 2 Output Hubs

Instruction Manual

Thank you for your purchase of the Larson Electronics HALP-24-2L-LED-2XH.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE HALP-24-2L-LED-2XH MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz

except those factory ordered with low voltage 11V to 25V AC/DC.

Warning: Check product label for correct input voltage!

Attach supply line wires to the appropriate light fixture wires as shown

in thediagram 

Secure each pair of wires according to the diagram. Utilize a junction box or

similar device and take precautionary steps for weatherproofing all

connections if installed in a location where water may come in contact with the

unit. Ensure the unit is properly grounded and that wiring is done according to

all local and national electrical/building codes.

The Larson Electronics HALP-24-2L-LED-2XH Hazardous Area LED Light Fixture is approved for use in Class I Division 2 Groups A,

B, C and D environments, NRTL certified to UL 1598A, and is specifically designed to handle the rigors of wet and corrosive marine

environments. This hazardous location LED light has a T4 temperature rating and carries a United States Coast Guard approval,

making it ideal for applications such as oil rigs, ships, offshore applications, petrochemical, manufacturing, chemical storage, and water

treatment centers. The HALP-24-2L-LED-2XH also features either two 1/2" or 3/4" NPT threaded wiring hubs on both ends for a total of

four.

HALP-24-2L-LED-2XH

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2 of 2

INSTALLATION

1. Install fixture to surface with four mounting brackets (mounting hardware not included).

2. Remove lens by releasing latches that secure the lens. The lens will suspend by the tethers inside the

fixture.

3. Remove lamps.

4. Twist wing nuts ¼ turn counter clockwise to release the ballast tray from the housing.

5. Electrical voltages and frequency are listed on the ballast tray for reference.

6. For supply connections use conductors suitable for min. 90° C.

7. Connect internal wires per wiring diagram on ballast, and according to NEC requirements.

8. Replace the ballast tray and twist wing nuts ¼ turn clockwise to secure.

9. Install lamps.

10. Replace lens and secure all latches.

MAINTENANCE

Electrical and mechanical inspection of all components must be performed on a regularly scheduled basic, determined by

the environment and frequency of use. Itisrecommended that inspection be performed a minimum ofonce a year.

WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND

MAINTENANCE. INSTALLATION ANDMAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND

COMPETENT ELECTRICIAN.

1. Inspect all contact wire terminals for tightness. Discoloration due to excessive heat is an indicator of a possible

problem and should be thoroughly investigated and repaired as necessary.

2. Inspect contacts for signs of wear and replace if necessary.

3. Clean exterior surfaces making sure nameplates remain legible.

If any part of the light appears to be missing, broken, or show signs of damage—discontinue use immediately! This

condition could cause serious or fatal personal injury due to electrocution and/or equipment damage. Repair with the

proper replacement part(s) before continuing service.

SURFACE MOUNTING

Flange type aluminum mounts attached at each end of the fixture enables it to be simply secured to any surface. The

mounts provide some shock absorbency protection while enabling the user to simply mount the fixture with the through-hole

taps that protrude on each side of the fixture. The mounting holes are 14.91" inches on center apart along the top of this

hazardous location light. The mounting holes are 9.5" inches on center across the top of the light.

PENDANT MOUNTING

This light fixture can hang from the ceiling suspected by rigid pipe. Each fixture is equipped with either two 1/2" or 3/4" NPT

hubs on either side of the fixture. Operators will bring rigid pipe down to the threaded mounting ups. The wiring is fed down

through the rigid pipe to one of the NPT hubs and tied to the fixture`s lead wires to complete the electrical connection. The

remaining pendant hub provides support for the opposite end of the fixture.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The HALP-24-2L-LED-2XH is designed to provide years of reliable performance. Should the need for replacement parts

arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics LEDWL-5-M Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-DL-12-25-1523 Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-24-1X150LED-V3 Bedienungsanleitung

Larson Electronics

Larson Electronics IND-RL-HDB-BX9-120V Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-48-1X100LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-16C-1MLED-50 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-150W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics TPM-GL20004-12C-1227-10C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT-PSC Bedienungsanleitung

Larson Electronics

Larson Electronics SOL240-2XWP50E2X200A-RMBB-DNS-7.63SQ Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-LED-150W-RT-140DB-480V Bedienungsanleitung

Larson Electronics

Larson Electronics IIND-DBL-36-1L-R1-120V Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-QP-1X150LED-100 Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-15WLED-PC-GR30 Bedienungsanleitung

Larson Electronics

Larson Electronics LM-20-3S-EW-LV Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-MPM-150LED Handbuch

Larson Electronics

Larson Electronics EPL-TL-1X10W-C-PA-XFSW Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-PT-150LTL-LED-480V Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-AMB-150LED-150-140DB Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-120-150-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-HB-160LED Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-PT-2X150LED-RT Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung