Larson Electronics HAL-MB-185LED-CPR-100 Bedienungsanleitung

HAL-MB-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

185 Watt Hazardous Location LED Light - Magnetic

Mount - C1D2 - ATEX - 100 foot Cord w/ EXP Plug

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in solid state

lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a conventional

HIDluminaire.

An internal, universal input, power-factor-corrected switch-mode supply allows it to be used from any

nominal 90-305V AC, 50/60Hz supply without any variation in light output.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system withan equipment-grounding conductor.

To avoidexplosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

Do not operate in ambient temperatures abovethose indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

MOUNTING

This explosion proof LED light fixture is comprised of a 16x14 inch LED light head mounted atop a legged

base stand fabricated from non sparking aluminum, with a separate shelf type magnetic mounting

bracket that allows mounting to ferrous metallic surfaces. The lamp can be easily adjusted up or

down 90 degrees and locked into position by simply loosening the two T-handle adjustment screws

located on either side of the light head and retightening them once the desired angle is found. The

magnetic mounting bracket for this unit includes six 200 lbs. grip magnetic bases which provide a total of

1,200 lbs. of grip and allows operators to mount the unit to walls and flat metallic surfaces. Users simply

attach the magnetic mounting bracket to the desired surface, then hang the lamp assembly from the

bracket.

WARNING: If there is moisture present, or chance of it, in the conduit system then necessary

precautions should be taken by the installer to prevent the moisture from entering through the cable or

conduit and entering the fixture. Failure to comply with the above could void the warranty.

HAL-MB-185LED-CPR-100

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

WIRING (see attached wiring diagram)

This unit comes preconfigured with selected cord cap. The is outfitted with 100` of 16/3 chemical and

abrasion resistant SOOW cord that is fitted with an explosion proof cord cap for easy connection to

explosion proof outlets. Plug options include a 5-15 15 amp straight blade plug for use with 120V

explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets,

or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof outlets. **PLEASE

NOTE** voltage ratings on plugs and outlets are MAXIMUM voltage. For low voltage applications,

proper voltage must be applied to the outlet or damage to the light fixture will occur.

MAINTENANCE

Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will

voidthe warranty.

1. Perform visual,mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It

is recommendedto follow an Electrical Preventive Maintenance Program as described in NFPA

70B: Recommendedpractice for Electrical Equipment.

2. The lens should be cleaned periodically as neededto ensure continued photometric performance.

Clean the lens with a damp, non-abrasive,lint-free cloth. If not sufficient, use mild soapor a liquid

cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e.excessive dust build-up). Clean with a non-abrasive cloth if

needed.

4. Do not operate if the lens is cracked or damaged. All fasteners shouldbe properly seated.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER

INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [email protected] OR BY PHONE AT

1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics EPL-LQP-2X150RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPEXC-1C-10.3-GFI-50C-BCE Bedienungsanleitung

Larson Electronics

Larson Electronics IND-LP-SS-24-2X2-2L-UVC Bedienungsanleitung

Larson Electronics

Larson Electronics EPLFL-26W-P-LED-25 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-2051-M Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-48-2L-LED-BLC Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-48-1X4-2X50LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-SBDL-150RT-48 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-BS-70-100 Handbuch

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-140DB-JB3 Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-24-2L-LVSOL-80C-C1D2-20C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-TL-1X10W-C-DF-PA Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-LED-50W-RT-JB2 Bedienungsanleitung

Larson Electronics

Larson Electronics LEDLB-12ET-IR-M Bedienungsanleitung

Larson Electronics

Larson Electronics LEDP5W-60XC-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics LEDHWP-900-DNMS Bedienungsanleitung

Larson Electronics

Larson Electronics PTB-1-75FT Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT-PSC Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-48-1X4-2X50LED-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics C1D1-2 Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-C-4XM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-480V-IBSC Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung