Larson Electronics HAL-SL-10-20X-LED Bedienungsanleitung

HAL-SL-10-20X-LED

200ft Hazardous Location LED String Lights

10 Lamps - Non-Metallic - Chemical Resistant - CID2

Instruction Manual

Thank you for your purchase of the Larson Electronics HAL-SL-10-20X-LED string lights.

WARNING

TO AVOID THE RISK OFFIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL

APPLICABLE ELECTRICAL CODES.

TO AVOID ELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

The HAL-SL-10-20X-LED from Larson Electronics is an Explosion Proof 200` LED String Light Set that is UL Listed Class I

Division 2 Groups A, B, C and D and is ideal for temporary work lighting and inspection activities in hazardous locations

requiring explosion proof protection. This 100 watt explosion proof LED string light set from Larson Electronics produces a

total combined output of 10,500 lumens of bright white light.

MOUNTING

USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OFTHIS DEVICE. WHEN EXTENSION

CORD IS CONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE MUST

BE SUITABLE FOR HAZARDOUS LOCATION INVOLVED. IMPROPER USE OF THIS DEVICE, ASSOCIATED PLUG,

RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO PERSONNEL.

PERIODIC INSPECTION OF THE RECEPTACLE AND CORD IS NECESSARY.

THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, ORANY SEVERE ABRASIONS, AND IFANY ARE

FOUND, THE CORD MUST BEREPLACED BEFORE RESUMING USE OFTHE UNIT.

ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION ANDMAINTENANCE.

INSTALLATION ANDMAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND COMPETENT

ELECTRICIAN.

IF ANY PARTS OF THE RECEPTACLE OR PLUG APPEAR TOBE MISSING, BROKEN, ORSHOW SIGNS OR

DAMAGE, DISCONTINUE USE IMMEDIATELY. REPLACE WITH THE PROPER REPLACEMENT PART(S) BEFORE

CONTINUING SERVICE.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

The HAL-SL-10-20X-LED from Larson Electronics is comprised of 10 LED

work lights equipped with hanging eye-bolts or quick links attached to the rear

mounting plate of each light. Open the eye bolt on each light and hang in the

desired location as needed, closing each eye bolt securely once the light is in

the desired location. The receptacle at the end of the string is also equipped

with a hanging eye-bolt that facilitates mounting in the same way. This allows

the user to attach another string light if needed for added distance, or any tools

rated for the same voltage and equipped with a compatible explosion proof

plug. See below for specifics on operating the explosion proof receptacle and

plug within the hazardous area.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

HAL-SL-10-20X-LED

WIRING

We strongly encourage a licensed electrician install this product, in all locations, especially in outdoor areas where

weatherproofing may be required.

Warning: Check product label for correct input voltage!

This unit comes pre-wired from factory with the selected cord cap. Take precautionary steps for weatherproofing all

connections if installed in a location where water may come in contact with the unit. All outdoor installations and indoor

installations near a wet location require the use of a GFCI device for safety, according to the National Electrical Code®

(NEC). Ensure the unit is properly grounded. Follow all applicable local and national electrical and building code when

installing to maintain safety within the hazardous area. This explosion proof LED string light is equipped with a 25 foot

whip of 16/3 chemical and abrasion resistant SOOW cord that is fitted with an explosion proof cord cap for easy

connection to explosion proof outlets. Plug option is selected when ordering, check product labels for specifications

before connecting to power source.

**PLEASE NOTE** voltage ratings on plugs and outlets are MAXIMUM voltage. For low voltage applications, proper

voltage must be applied to the outlet or damage to the light fixture will occur.

Position device near work area for operation. Run cable to nearby power source outputting the correct voltage as

identified on the product label. Insert and twist-lock explosion-proof plug into a compatible receptacle within the

hazardous environment. See plug operation below.

PLUG OPERATION

Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into receptacle and

is rotated clockwise.

1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all

the way into receptacle until it cannot go further.

2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also mechanically

locks plug into receptacle so it cannot be pulled out.

3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

OPERATION

The lamps are“instant-on” and will illuminate once power issupplied.

LAMP REPLACEMENT

1. Loosen and remove guard (Turn counter-clockwise).

2. Unscrew globe (Turn counter-clockwise).

3. Remove and replace bulb with matching lamp.

4. Inspect gasket(s). If worn or damaged, it must be replaced to insure watertight seal.

5. Screw globe completely onto lamp base (Turn clockwise).

6. Replace guard (Turn clockwise).

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the

life of the equipment. Perform visual, mechanical and electrical inspections on a regular basis. We

recommend routine checks to be made on a yearly basis. Frequency of use and environment

should determine this. It is recommended to follow an Electrical Preventive Maintenance Program

as described in NFPA 70B: Recommended practice for Electrical Equipment. Always check for

damaged or worn out parts before using the device. Inspect for good working condition prior to

storage and before re-use.

REPLACEMENT PARTS

The HAL-SL-10-20X-LED is designed to provide years of reliable performance. Should the need

for replacement parts arise, please contact Larson Electronics.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics EPL-EMG-LED-100W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-16C-150LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-1L Bedienungsanleitung

Larson Electronics

Larson Electronics SOL240-2XWP50E2X200A-RMBB-DNS-7.63SQ Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-QP-1X150RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-150LED-RT-SP0010-200C Series Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-48VDC-R2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-24-2L-LED-VISRED Bedienungsanleitung

Larson Electronics

Larson Electronics LEDLB-12E-F-M-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics 9200-RL-LED-S-SCM-WR Handbuch

Larson Electronics

Larson Electronics EPL-16C-2X150LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-EMG-CM-42W Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-HB-150LED-RT-CM Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-QP-1X150LED-100 Bedienungsanleitung

Larson Electronics

Larson Electronics IND-HVAC-DTW-XX-SP0108-120W Bedienungsanleitung

Larson Electronics

Larson Electronics EMGBALL-LED1-LV Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-NSF Bedienungsanleitung

Larson Electronics

Larson Electronics LED18W-PAR36 Bedienungsanleitung

Larson Electronics

Larson Electronics IND-RL-HDB-BX9-120V Bedienungsanleitung

Larson Electronics

Larson Electronics EXHL-TRN-LE4-FKWL Series Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-7WLED-GR30 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-29000GB Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-50W-RT-JB5 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung