Larson Electronics EPL-150LED-RT-SP0010-200C Series Bedienungsanleitung

EPL-xx-150LED-RT-SP0010-200C

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Replacement Wiring Assembly for Portable Explosion Proof Lights -

200ft 16/3 SOOW - Exp Proof Plug

Instruction Manual

Replacement wiring assembly for portable explosion proof lights.

Includes:

200ft 16/3 SOOW cord, Explosion proof plug (exp cord cap options), Junction box, Nipple, CGB, Terminal

strip.

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

•Make sure the supply voltage is within the luminaires’ voltage rating.

•Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

INSTALLATION

1. Disconnect power prior to performing maintenance!

2. Open junction box cover of existing fixture. There are nubs on top cover for opening with a screwdriver,

wrench, or similar tool. Turn cover counter-clockwise to remove.

3. Once the top cover has been removed, pull out the wiring and make note of how they are connected.

4. Disconnect wiring.

5. Unscrew the CGB cord grip from the base of the junction box to remove old cord.

6. Loosen set screw on back of light holding junction box and twist junction box counter-clockwise to

remove from the light fixture.

7. Open top cover of new junction box.

8. Run cord from back of light fixture through new junction box and nipple.

9. Attach junction box to back of light while making sure no wires get twisted.

10. Tighten set screw on back of fixture for the NPT port holding nipple and junction box in place.

11. Make sure CGB cord grip and cord is connected to junction box and tight.

12. Once junction box is installed and cord with cord grip is attached, make all wire connections.

13. Tuck wires into junction box and close top cover by turning clockwise. Make sure there are no wires

protruding or getting pinched when closing top cover.

Ensure all wire connections have been made properly and that all points are closed off and tight before

operating.

WIRING

This unit comes preconfigured with the selected explosion proof cord cap. Run cord from light and plug into

matching receptacle. Follow all applicable local, state, and National Electrical Code for the hazardous area!

EPL-xx-150LED-RT-SP0010-200C

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

WARNING: ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION

AND MAINTENANCE. INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A

TRAINED AND COMPETENT ELECTRICIAN.

If any part of the plug appears to be missing, broken, or show signs of damage—discontinue use immediately!

This condition could cause serious or fatal personal injury due to electrocution and/or equipment damage.

Repair with the proper replacement part(s) before continuing service.

During the inspections, perform the following steps:

1. Inspect all contact wire terminals for tightness and re-torque if necessary. NOTE: Discoloration due to

excessive heat is an indicator of potential issues and should be thoroughly investigated and repaired as

necessary.

2. Explosion Proof Plugs: Check grounding and bonding for correct installation. Secure connections and

retorque if necessary.

3. Check gaskets for deterioration and replace if necessary.

4. Clean exterior surfaces to ensure the nameplates remain legible.

5. Inspect cable grip tightness to ensure proper cord/cable gripping.

6. Inspect all parts and replace those which are broken or excessively worn.

7. Check the contacts for signs of excessive arcing or burning and replace if necessary.

USE AND CARE

Unauthorized modification may impair the function and/or safety of the extension cord and could affect the life

of the equipment. Always check damaged or worn out parts before using the unit. When extension cord is not

in use, store it in a secure place. Inspect for good working condition prior to storage and before re-use.

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 or [email protected] for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Inhaltsverzeichnis

Andere Larson Electronics Beleuchtungsausrüstung Handbücher

Larson Electronics

Larson Electronics EPL-MPM-150LED Handbuch

Larson Electronics

Larson Electronics TPM-2XLEDEQ-4X3-CPR Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-QP-2X150RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-50LED-100 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-16C-1MLED-50 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-6XMB-10 Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-HB-100LED-RT-UVA-10C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-48-2L-LED-BLC Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-TP-2XRUL10 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-MB-185LED-CPR-100 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-48-2L-T12VHO Bedienungsanleitung

Larson Electronics

Larson Electronics LM-21-9.1-4S-EW Bedienungsanleitung

Larson Electronics

Larson Electronics FRL-4P-S1-60-1X-T5HO-130W-UVC Bedienungsanleitung

Larson Electronics

Larson Electronics IND-HVAC-DTW-XX-SP0108-120W Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-FL1524-LED Series Bedienungsanleitung

Larson Electronics

Larson Electronics C1D2 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-2051-M Bedienungsanleitung

Larson Electronics

Larson Electronics EXP-EMG-EXT-LE6-3L Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-IBSC Bedienungsanleitung

Larson Electronics

Larson Electronics IND-DHA-FUVC-EX-48-3L-V2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-150LED-RT-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-PT-150LTL-LED-480V Bedienungsanleitung

Larson Electronics

Larson Electronics EPLX-SL-PT-3X80W.RD2-TRC-20X-100C Bedienungsanleitung

Larson Electronics

Larson Electronics GSLEDIP6-C1D2 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung