LaserLiner Quadrum OneTouch Bedienungsanleitung

Quadrum OneTouch / Quadrum OneTouch Green

Laser

530-670 nm

man

IP 66

101

112

123

134

145

156

167

178

189

200

211

222

233

auto

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 1 10.03.11 08:58

Quadrum OneTounch / Quadrum OneTounch Green

Caution: Prior to using the laser, you must read the safety instructions for

laser class 3R thoroughly. Warning signs must not be removed from the laser

measuring device! Do not look directly into the beam. Lasers must be kept

out of reach of children. Never intentionally aim the device at people. This is a

quality laser measuring device and is 100% factory adjusted within the stated

tolerance. For reasons of product liability, we must also draw your attention

to the following: Regularly check the calibration before use, after transport

and after extended periods of storage. We also wish to point out that absolu-

te calibration is only possible in a specialist workshop. Calibration by yourself

is only approximate and the accuracy of the calibration will depend on the

care with which you proceed.

Laser radiation!

Avoid direct exposure

to the eyes.

Laser class 3R

< 5 mW Ċ530 - 670 nm

EN60825-1:2007-10

General safety instructions

Please read the operating instructions as well as the enclosed

brochures "Guarantee and additional notices" and "Laser class 3R

safety instructions". Follow the instructions they contain. Safely

keep these documents for future reference.

Fully automatic rotary laser with red or green laser

technology.

– Laser modes: spot, scan, rotary and hand receiver mode

– All functions can be controlled remotely.

– optional SensoLite 310: Laser receiver range up to 300 m radius

– optional SensoLite 410: Laser receiver range up to 400 m radius

– optional SensoMaster 400 (Quadrum red only): Laser receiver range in

excess of 300 m radius. With longer laser receiver unit and millimetre exact

distance reading for laser level.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 13 10.03.11 08:58

Special product features and functions

The rotary laser starts up by rotating and aligning itself

automatically. It is set to the required initial position (to within an operating

angle of ± 5°) and the automatic system then performs the necessary fine

adjustment, with two electronic measurement sensors detecting the X and

Y axes.

The anti-drift system (ADS) prevents erroneous or inaccurate

measurements. How it works: The laser automatically switches to active

ADS mode 35 seconds after being switched on and is permanently checked

to ensure it is aligned correctly. If the device moves due to the influence of

external factors or the laser loses its height reference, the laser will come to

a standstill. Additionally, the laser flashes and the tilt LED is lit continuously.

To continue working switch the device off and on again. Erroneous and

inaccurate measurements are thus prevented simply and reliably.

ADS is automatically active after the device is switched on in order to prevent

changes in position caused by external influences affecting the set-up device. The

tilt LED flashes to indicate that the ADS function is active; see the diagram below.

Press the ON/OFF button for 3 seconds to switch off the ADS function.

ON:

Rotation begins External

influence

Adjustment phase

Sensor Automatic,

X and Y LEDs flashing

X and Y LEDs

permanently on The

laser

remains stationary as

a precaution, the laser

flashes and the tilt

LED is lit continuously.

ADS active after

35 seconds, rapid

flashing of the tilt LED.

ADS function

The ADS does not activate the monitoring function until 35 seconds

after the laser levelling procedure has been completed (set-up phase).

The tilt, X and Y LEDs flash during the set-up phase; the tilt LED flashes

rapidly and the X and Y LEDs are permanently on when ADS is active.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 14 10.03.2011 17:02:25 Uhr

Quadrum OneTounch / Quadrum OneTounch Green

Transport LOCK: The device is protected by a special motor

brake during transport.

IP 66

The device characterised by specific protection against

dustand rain.

Quadrum OneTouch Green: green laser technology

The distance at which a laser is visible to the naked eye depends on its colour

i.e. wavelength. This is because of the human eye's physiology – green

appears brighter to us than red. Depending on ambient light, green lasers

are therefore many times more visible than red lasers; in indoor areas this is

as much as 12 times brighter. This permits applications on dark surfaces, over

longer distances and work in very bright ambient light. A red laser with a 635

nm wavelength is used as a reference value for brightness differentiation.

In contrast to red lasers, green laser light can only be produced indirectly.

This is a source of potential characteristic fluctuations:

– The optimal operating temperature is 20°C. Outside its operating

temperature range of 0 – 40°C Quadrum OneTouch Green is darker.

IMPORTANT: Allow the unit enough time to adapt to the ambient

temperature before switching the unit on.

– Laser brightness may vary somewhat from one unit to another. This is a

natural phenomena and excluded from warranty claims.

– Green Laser will only work with certain Receivers. The maximum range

of the Receiver is shorter, please refer to technical details.

Horizontal

levelling Slope function

auto man

Space grids: These show the laser planes and functions.

auto: Automatic alignment / man: Manual alignment

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 15 10.03.11 08:59

–

AAA

–+

AAA

–

Battery charging

– Charge the device's battery completely prior to use.

– Connect the charger to mains power supply and the charging socket (H) of

the battery compartment (J). Please only use the charger supplied; using a

different charger will invalidate the warranty. The rechargeable battery can

also be charged when it is not inserted in the device.

– When the rechargeable battery is being charged, the LED on the charger (L)

lights up red. When the LED changes to green, charging is complete. When

the unit is not connected to the charger the power charger's LED lamp will

blink.

– Alkaline batteries (4 x type C) can be used as

an alternative. Insert them in the battery com-

partment (I) as per the installation symbols.

– Insert battery (J) / battery compartment (I) into

slot (E) and secure it in place with fastening

screw (G). The electrical contacts (F) must be

connected.

– With the rechargeable battery inserted, the

device is ready to run even during charging.

– When all 4 LEDs (2, 4, 5, 6) light up briefly and

the device switches off, the batteries must be

replaced or the rechargeable battery charged.

Insert batteries into the remote control

– Observing the correct polarity.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 16 10.03.11 08:59

Quadrum OneTounch / Quadrum OneTounch Green

Prism head / laser beam outlet

Receiver diodes for remote

control (4 x)

Control panel (ON/OFF button)

5/8" thread (bottom)

Slot for rechargeable battery /

battery compartment

Electrical contacts

Battery compartment / battery

fastening nut

Charging socket

Battery compartment

Rechargeable battery

compartment

Mains unit / charger

Operation indicator

red: battery is charging

green: charging process complete

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 17 10.03.11 08:59

4675

auto/man function

auto/man function LED

LED off: automatic alignment

LED on: manual alignment

ON/OFF button

X axis LED

Tilt function LED

Y axis LED

Battery display

Rotary speed for selection, 600 /

300 / 120 / 60 / 0 rpm

Positioning button

(rotate to the right)

Positioning button

(rotate to the left)

auto/man. function:

Y axis proceed as above

auto/man. function:

Y axis proceed as below

auto/man. function:

X axis proceed as above

auto/man. function:

X axis proceed as below

Scan mode

Operation indicator

Infrared signal emitter

Control panel

Quadrum OneTouch Remote control

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 18 10.03.11 08:59

Quadrum OneTounch / Quadrum OneTounch Green

±5°

man

If the device has been placed on a surface with too much of a slope

(more than 5°), the prism head remains stationary and the laser starts

to flash. The device must then be placed on a more even surface.

auto/man function LED OFF: Automatic alignment

– The device levels itself automatically to within a range of ±5°. The laser

rotates and the tilt, X and Y LEDs flash during the set-up phase. When

levelling is complete, the tilt LED flashes rapidly and the X and Y LEDs are

permanently on. The laser rotates at maximum speed. Refer also to the

sections about "Sensor Automatic" and "ADS Tilt".

Horizontal levelling

– Horizontal: Position the device on a level surface or

on a tripod.

– Press the "ON/OFF" switch

auto

Slope function up to 5° – horizontal

This function deactivates the automatic sensor. To use the function, press the

auto/man button. The plus/minus buttons are used to re-adjust the slope by

means of a motor. In the process the X-and Y-axis can be adjust separately.

Refer to the illustrations below.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 19 10.03.11 08:59

man

Slope function > 5°

Steeper slopes can be set using the angle plate,

which is available as an optional extra (product

ref. 080.75). TIP: Allow the device to align itself

automatically and set the angle plate to the zero

position. Then press the auto/man button to switch

the automatic sensor off. Finally, incline the device

to the angle you require.

auto/man function LED ON: Manual alignment

Laser modes

Rotary mode

The following speeds can be set using the rotary

button: 0, 60, 120, 300, 600 rpm

Spot mode

You access spot mode by pressing the rotary

button repeatedly until the laser stops rotating.

The laser can then be positioned exactly at the

measuring point by means of the direction

buttons.

Scan mode

The scan button can be used to activate and set

a lightintensive segment in 4 different widths.

You position the segment via the direction

buttons.

Hand receiver mode

Working with the laser receiver (available as an

optional extra): Set the rotary laser to maximum

speed and switch on the laser receiver. Refer to

the operating instructions for the respective laser

receiver about this.

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 20 10.03.11 08:59

Quadrum OneTounch / Quadrum OneTounch Green

EU directives and disposal

This device complies with all necessary standards

for the free movement of goods within the EU.

This product is an electric device and must be collected

separately for disposal according to the European

Directive on waste electrical and electronic equipment.

Further safety and supplementary notices at:

www.laserliner.com/info

Technical data

(Subject to technical alterations)

Self-levelling range ± 5°

Accurancy ± 0,75 mm / 10 m

Horizontal levelling Automatic with electronic

sensors and servo motors

Self-levelling alignment time Approx. 35 seconds over the

entire operating angle

Rotation speed 0, 60, 120, 300, 600 RPM

Remote control Infrared IR

Laser wavelengths green / red 635 nm / 532 nm

Laser class red / green 3R (EN60825-1:2007-10)

Laser output rating red / green < 5 mW

Power supply High-performance rechargeable

battery / batteries (4 x type C)

Rechargeable battery life red / green

approx. 35 h / approx. 14 h

Non-rechargeable battery life red / green

approx. 50 h / approx. 8 h

Battery recharging time ca. 6 h

Operating temperature red / green -10°C ... + 50°C / 0°C ... + 40°C

Storage temperature -10°C ... + 70°C

Protection class IP 66

Dimensions (W x H x D) /

Weight (incl. batteries) 215 x 205 x 165 mm /

2,6 kg

Remote control

Power supply 2 x type AAA

Remote control range max. 30 m (IR-Control)

Weight (incl. battery) 0,07kg

Manual_QuadrumOneTouch_Rev.0211_DE_NO.indd 21 10.03.11 08:59

Andere Handbücher für Quadrum OneTouch

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LaserLiner Messgerät Handbücher

LaserLiner

LaserLiner PrecisionCross-Laser PCL 5P RXR Bedienungsanleitung

LaserLiner

LaserLiner MultiMeter-PocketBox Bedienungsanleitung

LaserLiner

LaserLiner LaserRange-Master T3 Bedienungsanleitung

LaserLiner

LaserLiner RangeXtender 40 Bedienungsanleitung

LaserLiner

LaserLiner CompactLine-Laser G360 Bedienungsanleitung

LaserLiner

LaserLiner MultiFinder Pro Bedienungsanleitung

LaserLiner

LaserLiner MultiScanner Plus Bedienungsanleitung

LaserLiner

LaserLiner Quadrum Bedienungsanleitung

LaserLiner

LaserLiner RollPilot D12 Bedienungsanleitung

LaserLiner

LaserLiner MetalliFinder Pro Bedienungsanleitung

LaserLiner

LaserLiner AutoSmart-Laser Bedienungsanleitung

LaserLiner

LaserLiner LaserRange-Master Gi7 Pro Bedienungsanleitung

LaserLiner

LaserLiner AutoCross-Laser 360 PowerBright Bedienungsanleitung

LaserLiner

LaserLiner MoistureMaster Compact Bedienungsanleitung

LaserLiner

LaserLiner AutoControl-Master ACM Bedienungsanleitung

LaserLiner

LaserLiner ZipLevel Plus 30 Bedienungsanleitung

LaserLiner

LaserLiner LaserRangeMaster Pocket Bedienungsanleitung

LaserLiner

LaserLiner CompactPlane-Laser 3D Bedienungsanleitung

LaserLiner

LaserLiner LaserMeter X20 Bedienungsanleitung

LaserLiner

LaserLiner LaserRange-Master T4 Pro Bedienungsanleitung

LaserLiner

LaserLiner RollPilot Mini Bedienungsanleitung

LaserLiner

LaserLiner 4K5 FL 500 Bedienungsanleitung

LaserLiner

LaserLiner DampFinder Plus Bedienungsanleitung

LaserLiner

LaserLiner SensoLite 410 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung