LaserLiner MetalliFinder Pro Bedienungsanleitung

MetalliFinder Pro

Manual_MetalliFinder-Pro_Rev.0909.indd Abs1 12.10.2009 10:17:35 Uhr

3 2 15

467

9 8

Operation

1. Battery exchange:

Open the battery compartment on the back of the tool and

connect up a new 9V battery (type 6LR 61). If the symbol 8.)

appears in the display, you should replace the battery as soon

as possible.

2. Switching-on and detection:

The MetalliFinder Pro can detect metals up to a depth of

75 mm and also localise live wires. For safety reasons, the AC

voltage warning is always active. The „Voltage (AC) found“

LED (b) lights up if a live line is located within the measuring

range.

Operating elements

aLED Measuring centre

bLED „Current (AC) found“

cSet button: Change over

material types – iron pipes,

structural steel, copper pipes.

dON/OFF button/

Toggle between scan modes:

AC voltage search,

metal search

e Calibration button

f Back: Battery cover

LC-Display

1Symbol:

AC Search activated (AC)

2Symbol Metal Search:

iron pipes activated

3Symbol Metal Search:

structural steel activated

4Symbol Metal Search:

copper pipes activated

5Calibration symbol (CAL)

6Symbol: Auto-test completed

(READY)

7Symbol: Auto-test error (ERROR)

8Low battery display

9Depth display in mm,

bar display

Manual_MetalliFinder-Pro_Rev.0909.indd 06 12.10.2009 10:17:53 Uhr

MetalliFinder Pro

Metal Search:

Press the ON/OFF button (d.) in order to activate Metal Search.

When Metal Search is activated, the symbol for the selected

mode (2. - 4.) appears in the display.

AC Search AC:

Press the ON/OFF button (d.) in order to activate AC Search.

When AC Search is activated, the AC symbol (1.) appears in

the display.

3. Calibration:

Press the CAL (e.) button to automatically calibrate the tool

in the selected mode. The CAL (5.) symbol appears for about

2 secs. in the display. When calibration has been successfully

completed, the symbol READY (6.) is displayed, if an error has

occurred, this is indicated by the symbol ERROR (7.).

Tip 1: Calibration error: If calibration is unsuccessful, this is

probably because the tool is located directly above an object

of the kind being searched for. Move the device to a different

position on the surface and try calibrating once more.

Tip 2: Detection error: To avoid detection errors, the

MetalliFinder should be kept in contact with the relevant

surface throughout the detection process.

4. Switching-off:

Press the Set and ON/OFF buttons (c, d) simultaneously. The

tool automatically switches off about 2 minutes after the last

search operation.

Scan modes:

A. Metal Search, Depth Measurement:

Metal Search offers three different detection modes which

are optimised for the different materials concerned. Select the

desired mode using the set button (c.).

Structural steel Iron pipes Copper pipes

Your selection is shown on the display by means of symbols

(2) to (4).

Manual_MetalliFinder-Pro_Rev.0909.indd 07 12.10.2009 10:17:55 Uhr

40 mm

75 mm

40 mm

75 mm

After successful calibration, the depth display 9.) indicates as

follows as metal is approached:

Metal detection begins at a distance of about 75mm. The

indicated value lessens as the tool approaches further, until it

is located directly above the metal object. In this position, the

distance to the metal object, i.e. the depth, is displayed (e.g.

about 25mm).

Tip 3: Localisation of metal:

Because of its high sensitivity, the MetalliFinder Pro can

normally detect objects in a broad radius beneath the relevant

surface. If you want to determine the actual centre of the

hidden object, you must move the MetalliFinder from both left

and right towards the object.

AFirst of all, move the device across the surface until the

Measuring centre LED (1) lights up briefly and an acoustic

signal sounds once.

BNext, move the device in the other direction. When

the device is above the target object, the LED (1) lights up

continuously and a constant signal sounds.

Manual_MetalliFinder-Pro_Rev.0909.indd 08 12.10.2009 10:17:56 Uhr

MetalliFinder Pro

The device now indicates the start and end of the target

object.

Mark the positions on the left (L) and right (R) side of the

object (depth display (9) at smallest depth). The actual middle

(M) of the object is halfway between the two markings.

B. AC Search (AC):

This mode can be used to specifically locate live lines. Press the

ON/OFF button (d) to activate the mode; the AC symbol (1)

appears on the display. As soon as the device nears a live line,

an acoustic signal sounds and the Measuring centre LED (a)

lights up. Continue to move the device until it stops emitting

visual and acoustic signals. Repeat the procedure from the

other side.

Mark the positions on the left (L) and right (R) side of the

object where the signal reaches maximum intensity. The

actual middle (M) of the object is halfway between the two

markings. In this mode, the bar display does not indicate the

distance to the target object.

Tip 4: Press the Calibration button (e) as soon as the LEDs (a,

b) light up and/or the warning signal sounds. Then move the

device towards the object again. This adjusts the accuracy,

enabling the device to get nearer to the target object.

Technical data:

Detection range: 3 mm to 75mm depth

Precision: ± 7mm detection depth

± 7mm centring precision

Working temperature: 0°C...40°C (32°F...104°F)

Storage temperature: -20°C ... 70°C

Power supply: 1 x 9V alkali battery (type 6LR 61)

Dimensions: 95 x 221 x 85 mm

Weight: 0,35 kg (incl. battery)

Technical specifications subject to change 09/2009

Warranty:

The warranty is valid for 2 years from the date of purchase.

The warranty does not cover damage caused by improper

use or storage, normal wear and tear, or defects which

only insignificantly impair the value of the product or its

functioning. Any tampering by unauthorised persons will

render this warranty void. In the event that you need to claim

warranty, please take the complete device together with all

information and the invoice to one of our dealers or send it in

to UMAREX-Laserliner.

Manual_MetalliFinder-Pro_Rev.0909.indd 09 12.10.2009 10:18:10 Uhr

MetalliFinder Pro

Manual_MetalliFinder-Pro_Rev.0909.indd 38 12.10.2009 10:20:09 Uhr

MetalliFinder Pro

SERVICE

Umarex GmbH & Co KG

– Laserliner –

Möhnestraße 149, 59755 Arnsberg, Germany

Tel.: +49 2932 638-300, Fax: +49 2932 638-333

[email protected]

Umarex GmbH & Co KG

Donnerfeld 2

59757 Arnsberg, Germany

Tel.: +49 2932 638-300, Fax: -333

www.laserliner.com

080.951A / Rev.0909

Manual_MetalliFinder-Pro_Rev.0909.indd Abs1:40 12.10.2009 10:20:51 Uhr

Andere Handbücher für MetalliFinder Pro

Inhaltsverzeichnis

Andere LaserLiner Messgerät Handbücher

LaserLiner

LaserLiner DampFinder Compact Plus Bedienungsanleitung

LaserLiner

LaserLiner LaserRangeMaster Pocket Bedienungsanleitung

LaserLiner

LaserLiner AC-Check Bedienungsanleitung

LaserLiner

LaserLiner MeterMaster Plus Bedienungsanleitung

LaserLiner

LaserLiner DistanceMaster Pocket Pro Bedienungsanleitung

LaserLiner

LaserLiner SuperSquare Bedienungsanleitung

LaserLiner

LaserLiner VideoScope XL Bedienungsanleitung

LaserLiner

LaserLiner AutoControl-Master ACM Bedienungsanleitung

LaserLiner

LaserLiner Duraplane G360 Bedienungsanleitung

LaserLiner

LaserLiner StarFinder Bedienungsanleitung

LaserLiner

LaserLiner SmartCross Bedienungsanleitung

LaserLiner

LaserLiner RangeXtender RX 30 Bedienungsanleitung

LaserLiner

LaserLiner DistanceMaster Pocket Bedienungsanleitung

LaserLiner

LaserLiner SensoCommander 120 Bedienungsanleitung

LaserLiner

LaserLiner EasyCross-Laser Green Bedienungsanleitung

LaserLiner

LaserLiner SensoLite 410 Bedienungsanleitung

LaserLiner

LaserLiner ClimaCheck Bedienungsanleitung

LaserLiner

LaserLiner RollPilot D12 Bedienungsanleitung

LaserLiner

LaserLiner HandyLaser Bedienungsanleitung

LaserLiner

LaserLiner DampCheck Bedienungsanleitung

LaserLiner

LaserLiner MoistureMaster Compact Bedienungsanleitung

LaserLiner

LaserLiner StarFinder Bedienungsanleitung

LaserLiner

LaserLiner ACL 4C Bedienungsanleitung

LaserLiner

LaserLiner MultiWet-Finder Plus Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung