LEGRAND Wattstopper PARTITION-SENSOR Bedienungsanleitung

No: IS-00717 – Rev. B

The Wattstopper PARTITION-SENSOR uses an infrared transmitter/receiver

pair to detect partition opening and closing and, in conjunction with other

Architectural Dimming products, coordinates lighting and shade preset functions

in areas such as partitioned meeting rooms or ballrooms. When used with the

unique partitioning programming features of Design Center and the divide and

combine widget on the Equinox touchscreens, the PARTITION-SENSOR allows

for automation of partitioned spaces and visual indication of room lighting and

shade status.

Wattstopper

Partition Sensor

Installation Instructions

No: IS-00717– Rev. B

PARTITION-SENSOR

Country of Origin: Made in China

FEATURES AND OPERATION OVERVIEW

OVERVIEW

• Excess gain (sensitivity) controlled by a screwdriver adjustment to prevent tampering

• Fixed optics

• Immune to most indirect ambient light and direct strobes

• Waterproof and enclosed in high impact plastic housing

• High speed (1100 μs Thru-Beam)

• Potted 6’ cable

• Power supply requirements: 10 to 30 VDC Note: PARTITION-SENSOR ships with a BZ-50 Power Pack

SPECIFICATIONS

Description Specication

Supply Voltage 10- 30 VDC; 5 volt models: 4.5 to 5.5 VDC, polarity protected

Current Requirements Sinks up to 100mA

Response Time Light State response = 600 usµ (1,100 µs Thru-Beam)

Dark State response = 600 µs (1,100 µ Thru-Beam)

LED Light Source Infrared = 880nm, Pulse-modulated LED

Excessive Gain Adjustment Sensitivity controlled by a screwdriver adjustment to prevent tampering

Range 65’ (20m)

Hysteresis Approximately 20% of signal

Light Immunity High immunity to most ambient light

Diagnostic Indicators Red LED = Output Status, Green LED = Power “ON”

Ambient Temperature -40°F to 158°F (-40° to 70°C)

Rugged Construction Chemical resistant, high impact polycarbonate house

Waterproof ratings: NEMA 4X, IP66

No: IS-00717 – Rev. B

BZ-50 Power Pack

120/277VAC, 50/60Hz, 225mA output

20A ballast or incandescent load

Motor load: 1HP@120/240VAC

Class 2 power supply

UL 2043 Plenum Rated

www.wattstopper.com • 800.879.8585

Power Pack Red

Red

+24VDC

Common Any 3-Wire

24VDC

Sensor

Control Output

White

Neut.

Blue

Black

Red

Hot Black

Switch

88T9

Appliance

Control

Lighting

Load

+24VDC

CEILING

WIRING LEGACY

JUNCTION BOX

Connect Input

+24VDC

120/277V

COMMON

+24VDC

Green

Red

White -

No Connect

Blue

Red

BLACK WIRE

RED WIRE

GREEN WIRE

WHITE WIRE

BLUE WIRE

1 In 1

2 In 2

3 In 3

4 In 4

5 +24

6 +24

8 +24

9 GND

10 P Cell

7 +24

LED 1

LED 2

Blue LEDs

Config.

Connect to

DLM local network

NOT Ethernet

LED 3

LED 4

24V Overload

Control Relay Terminal A

+24VDC 5, 6, 7, 8

Control Relay Te rminal B

INPUT 1, 2, 3, 4

PARTITION SENSOR WITH THE DLM SYSTEM

LMIN-104

NOTE: Requires a SPDT (single pole double throw) +24VDC Relay supplied by others

(OMRON LY2-DC24 Relay, PTF08A-E Socket)

• When partition is closed, the coil on the relay will be de-energized

• When partition is open, the coil on the relay will be energized

• 24 VDC Coil of relay connects to

Red = +24VDC

Green Out of Sensor = Common

NOTE 2: LMIN must be set so “Operating Mode” is Partition. In this mode, all four inputs are

dedicated to Partition detection and LMIN cannot be used with any other inputs

NOTE 3: Wall 1 = Input 1 • Wall 2 = Input 2 • Wall 3 = Input 3 • Wall 4 = Input 4

SENSOR ADJUSTMENT PROCEDURES

LIGHT SOURCE RECEIVER Step 1: Point the light beam emitted by the light source away from the receiver

Step 2: Turn the light source sensitivity adjustment fully clockwise (CW) to its maximum setting

Step 3: Monitor the output LED indicator on the receiver while moving the light beam emitted

from the light source in a scanning motion, rst from left to right and then up and down.

Use this technique to locate the mounting position that will ensure the best possible

beam alignment with the receiver.

Step 4: When acceptable beam alignment has been achieved, turn the sensitivity adjustment

fully counter clockwise (CCW)

Step 5: Turn the sensitivity adjustment clockwise (CW) 1/4 turn past the point the output LED

indicator toggles to the opposite state

PARTITION SENSOR WIRING DIAGRAM

No: IS-00717 – Rev. B

PARTITION SENSOR WIRING DIAGRAM

BZ-50 Power Pack

120/277VAC, 50/60Hz, 225mA output

20A ballast or incandescent load

Motor load: 1HP@120/240VAC

Class 2 power supply

UL 2043 Plenum Rated

www.wattstopper.com • 800.879.8585

Power Pack Red

Red

+24VDC

Common Any 3-Wire

24VDC

Sensor

Control Output

White

Neut.

Blue

Black

Red

Hot Black

Switch

88T9

Appliance

Control

Lighting

Load

+24VDC

CEILING

WIRING LEGACY

JUNCTION BOX

120/277V

DOOR

COMMON

+24VDC

Contact output

RECEIVER

TO:

- Contact Input Station

- LVOS

- Keypad Station

Green

Red

White - No Connect

White -

No Connect

Blue Black

BLACK WIRE

RED WIRE

GREEN WIRE

WHITE WIRE

BLUE WIRE

LIGHT SOURCE

Mount to flanges

on each side of the

sliding door or partition

Align sensors on

all three axis

PWR

OUT

PWR

NOTE: In Design Center, make sure it is set to

normally closed (NC) polarity for the sensor

OUTPUT Green

INPUT 1, 2, 3, 4

Green, Blue Wire

OUTPUT Black

Ground

Black Wire

PARTITION SENSOR WITH THE

ARCHITECTURAL DIMMING SYSTEM

CIS

(Contact Input Station)

LVOS

KEYPAD

When partition is closed, contact is open

When partition is open, contact is closed

800.555.9891

www.legrand.us/wattstopper

No. IS-00717 – Rev. B

Wattstopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

Wattstopper garantit que ses produits sont

exempts de défauts de matériaux et de fabrication

pour une période de cinq (5) ans. Wattstopper

ne peut être tenu responsable de tout dommage

consécutif causé par ou lié à l’utilisation ou

à la performance de ce produit ou tout autre

dommage indirect lié à la perte de propriété, de

revenus, ou de profits, ou aux coûts d’enlèvement,

d’installation ou de réinstallation.

Wattstopper garantiza que sus productos

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida

de propiedad, renta o ganancias, o al costo

de extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

MULTI-VIEW LINE DRAWING

FRONT VIEW SIDE VIEW BACK VIEW

1-3/8”

2-1/2”

2-3/8”

1” PWR

Inhaltsverzeichnis

Andere LEGRAND Zubehör Handbücher

LEGRAND

LEGRAND Wattstopper EW-200-120 Bedienungsanleitung

LEGRAND

LEGRAND Dooxie 6 003 78 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper FSP-212 Bedienungsanleitung

LEGRAND

LEGRAND 0 672 25 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper UT-305-1 Bedienungsanleitung

LEGRAND

LEGRAND 419 12 Bedienungsanleitung

LEGRAND

LEGRAND Excel Life EM803PIR Bedienungsanleitung

LEGRAND

LEGRAND 6 946 90 Bedienungsanleitung

LEGRAND

LEGRAND 0 489 14 Bedienungsanleitung

LEGRAND

LEGRAND WS-250 Bedienungsanleitung

LEGRAND

LEGRAND 0 942 70 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RS-250 Bedienungsanleitung

LEGRAND

LEGRAND 845 21 Kurzanleitung

LEGRAND

LEGRAND 0 942 52 Bedienungsanleitung

LEGRAND

LEGRAND 843 26 Bedienungsanleitung

LEGRAND

LEGRAND 0 488 34 Bedienungsanleitung

LEGRAND

LEGRAND HPM D643/WES Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper FSP-211-CFG Bedienungsanleitung

LEGRAND

LEGRAND PW-100-W Bedienungsanleitung

LEGRAND

LEGRAND Radiant WWRR15LACCV2 Bedienungsanleitung

LEGRAND

LEGRAND TV/SAT Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DT-305 Bedienungsanleitung

LEGRAND

LEGRAND DX2 Series Bedienungsanleitung

LEGRAND

LEGRAND 896 20 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung