LEGRAND EasyIP VADDIO PCC Bedienungsanleitung

Complete Manual for the

EasyIP PCC and PCC Mini

Four-Camera Joystick Controllers

Document 411-0067-30 Rev A

October 2023

Contents

Overview 1

About this guide 1

Features 1

A quick look at the camera controller 2

Installation 3

Don’t void your warranty! 3

Cabling notes 3

Basic connections 4

Connecting the EasyIP PCC controller 4

Connecting the PCC Mini controller 5

Ensuring compatibility 5

Powering up 5

Initial device set-up and system administration tasks 6

Browser support 6

Initial device set-up using the Vaddio Device Controller 6

Initial device set-up using the Vaddio Deployment Tool 6

Manual access and initial device set-up 7

If the device is at 169.254.1.1 7

Device administration 8

Configuring access and other security settings 8

Compatibility with OBS Studio 9

Specifying time zone and NTP server 9

Configuring a static IP address for a device currently at 169.254.1.1 10

Changing from an automatically assigned address to a static IP address 11

Changing the device's hostname 11

Adding room information 12

Performance and behavior settings 13

Setting camera controller behavior 13

Pairing to cameras 14

Renaming video inputs 15

Courtesy HDMI output settings 15

Customizing the operator's interface 16

Creating an operator's page template 17

Adding controls to the page template 18

Naming your page template 19

System maintenance 20

Exporting and importing configuration data 20

Updating the firmware 22

Contacting Vaddio Technical Support and viewing diagnostic logs 23

Operating the four-camera joystick controller 24

Returning from standby 24

Controlling the preview camera 24

Storing a new preset on the camera 24

Doing more with the web interface 24

Controls you may have available 24

Status lights cheat sheet 25

Camera controller status lights 25

Power injector status light 25

Camera status lights 25

EasyIP Switch status lights 26

Command Line Interface SHell (CLISH) reference 27

Requirements 27

Usage notes 27

Getting more information 27

Typographical conventions 27

Camera and video management commands 28

camera home 28

camera pan 29

camera tilt 29

camera zoom 30

camera preset 31

camera focus 32

video mute 33

video source 33

video resolution 34

Communication commands 35

camera comm host 35

camera authenticate 35

network settings get 36

Maintenance and troubleshooting commands 37

network ping 37

monitor buttons 37

system standby 38

system reboot 38

system factory-reset 39

version 39

Information and session management commands 40

help 40

history 40

exit 41

Troubleshooting and care 42

iii

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Power issues 42

Network and communication issues 43

Video issues 44

Rebooting 44

Restoring factory defaults 45

Operation, storage, and care 46

Glossary 47

Index 49

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Overview

This guide provides information about:

nEasyIP PCC four-camera joystick controller, 999-57755-000 (worldwide)

nPCC Mini four-camera joystick controller, 999-57750-000 (worldwide)

About this guide

This guide covers:

nPhysical features and user interfaces

nAdministration, configuration, and maintenance tasks

nOperation

nCommand reference

nTroubleshooting

nGlossary

The EasyIP PCC and PCC Mini are very similar, but installation differs somewhat. For your convenience,

installation information is also available in these short guides:

nInstallation Guide for the EasyIP PCC Four-Camera Joystick Controller

nInstallation Guide for the PCC MiniFour-Camera Joystick Controller

The installation guides cover only the physical features, installation, and initial power-up.

Features

nSimple control of up to four cameras:

oEasyIP PCC for EasyIP cameras

oPCC Mini for other Vaddio cameras

nThree-axis Hall effect joystick

nIlluminated pushbuttons for camera selection

nWeb interface for operation and administrative control

nUse with the Vaddio Device Controller or manage from your PC

nYour EasyIP Switch powers the EasyIP PCC; a PoE+ mid-span power injector powers the PCC Mini

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

A quick look at the camera controller

The EasyIP PCC and PCC Mini look identical except for the model information.

Camera buttons (lower row)– Select the camera to use for the next shot (the preview camera). The

buttons are only illuminated if they are assigned to cameras.

Preset buttons (upper row) – Use these buttons to select presets 1 through 4 on the selected preview

camera. The buttons are only illuminated if the corresponding presets have been stored on the camera.

Joystick – Left/right to pan, forward/back to tilt, twist to zoom.

Kensington lock slot – Keep your joystick from adventuring away into the wide, wonderful world.

PoE+ Gigabit Ethernet port – Power and network connectivity, including access to cameras.

Courtesy HDMI output – Video from the camera you are currently controlling.

IP button – Press to overlay the device's IP address on the HDMI video output display.

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Installation

This section covers how to install and connect the product. It also provides safety information and other

guidance related to installing the product.

Note

This product is intended for installation and use only in environments where all RS-232 and PoE/PoE+

connections originate within the building.

Or in UL's preferred phrasing...

PoE-type networks connected to this equipment are for intra-building use only and should not

be connected to lines that run outside the building in which this product is located.

Don’t void your warranty!

Caution

This product is for indoor use. Do not install it outdoors or in a humid environment without the appropriate

protective enclosure. Do not allow it to come into contact with any liquid.

Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. If any of

these things happen, return it to Vaddio for safety and functional testing.

Cabling notes

Best practices for making cables:

nUse Cat-5e or better cable. We recommend shielded cabling if the cables will be coiled,

run tightly with other cables, or placed close to sources of electromagnetic interference

such as power lines or fluorescent light fixtures.

nUse high-quality standard RJ-45 connectors; 568B termination recommended.

nUse a high-quality crimping tool.

Caution

When building cables for Vaddio products, do not use pass-through RJ-45 connectors. If

they are crimped incorrectly, they can cause intermittent connections and degrade

signal quality. Incorrectly crimped pass-through connectors can also damage the

connectors on the product, which will void your warranty.

Intact – will make reliable contact

with the cable connector

Damaged – Bent contact fingers

will NOT make reliable contact

with the cable connector

Caution

Check your cables. Connecting a cable to the wrong port or using the wrong pin-out can result in

equipment damage and will void the warranty.

Pro tip

To prevent tragic mishaps, label both ends of every cable.

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Basic connections

Because the EasyIP PCC and PCC Mini are for different environments, the connections are different.

Connecting the EasyIP PCC controller

The EasyIP PCC connects to the EasyIP Switch that powers the rest of the EasyIP installation. A Vaddio

Device Controller provides access to the web interfaces of all the EasyIP products connected to the

switch.

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Connecting the PCC Mini controller

The PCC Mini connects to the network via a PoE+ mid-span power injector. A Vaddio Device Controller

provides access to Vaddio products on the same subnet.

Ensuring compatibility

The controller may be unable to communicate with Vaddio cameras if their firmware is out of date. When

you set up the controller, be sure the associated cameras have been updated to the latest firmware.

Powering up

When you power up the device for the first time, you will need to access the web interface to configure it

for operation.

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Initial device set-up and system administration tasks

When any Vaddio product is shipped from the factory, there is no admin password and the web interface

controls are not available. You will need to access the web interface and set the admin password. You

will then have access to the system administration tasks to define how the device behaves as an element

of your network.

Browser support

Supported web browsers:

nChrome®

nFirefox®

nMicrosoft® Edge®

nSafari®

Other browsers may also work.

Initial device set-up using the Vaddio Device Controller

The Vaddio Device Controller is a stand-alone tablet for working with Vaddio products' web interfaces.

To complete the initial device set-up with the Vaddio Device Controller:

1. Connect the touch-panel to the network on the same subnet as the products you need to work with –

for example, connect both to the same PoE+ switch.

2. Go to the touch-panel's Configuration page (gear icon)and select Scan.

3. Locate the device you need to work with, and select Use.

4. Select Exit to leave the Configuration page and open the device's web interface.

Note

The first time you access a device at a specific IP address, the Vaddio Device Controller's screen

may remain blank for 20 seconds or more.

5. Set the admin password.

If the Vaddio Device Controller does not find the device, verify that the Vaddio Device Controller and the

device are connected to the same subnet.

Initial device set-up using the Vaddio Deployment Tool

Be sure you have the current version of the Vaddio Deployment Tool. If you have a copy of the tool

already, compare its version information to the version shown on the release notes. This tool is available

as a free download at https://info.legrandav.com/VaddioDeploymentTool.

To complete the initial device set-up with the Vaddio Deployment Tool:

1. Power up the device if you have not done so already.

2. On the Find Devices page, click Scan. If the scan does not locate the device, your computer may be

on a different subnet. Click Advanced and specify the appropriate portion of the network to scan.

3. In the list of equipment that the scan discovers, locate the devices marked Not Set Up.

4. For each device that you need to work with, click the Not Set Up button and set the admin password

on the device detail page that opens.

The device shows up as unlocked after you set the admin password. You will then be able to log in to the

administrative web interface to complete system administration and other configuration tasks.

Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers

Andere Handbücher für EasyIP VADDIO PCC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LEGRAND Controller Handbücher

LEGRAND

LEGRAND Wattstopper DCLV2 Bedienungsanleitung

LEGRAND

LEGRAND adorne WNAL33/43 Bedienungsanleitung

LEGRAND

LEGRAND 0 698 74L Bedienungsanleitung

LEGRAND

LEGRAND Galion K8/H251-HK Bedienungsanleitung

LEGRAND

LEGRAND Tynetec ZXT473 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-101 Bedienungsanleitung

LEGRAND

LEGRAND 0 883 27 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMJA-8125-SM Bedienungsanleitung

LEGRAND

LEGRAND Mosaic Bedienungsanleitung

LEGRAND

LEGRAND HD4657M3 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-111-16M Bedienungsanleitung

LEGRAND

LEGRAND 0 884 06 Bedienungsanleitung

LEGRAND

LEGRAND Raritan SRC-0100 Bedienungsanleitung

LEGRAND

LEGRAND 0 488 64 Bedienungsanleitung

LEGRAND

LEGRAND 0 035 40 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DCLV2 Service-Handbuch

LEGRAND

LEGRAND 0 884 12 Bedienungsanleitung

LEGRAND

LEGRAND 784 28 Bedienungsanleitung

LEGRAND

LEGRAND VANTAGE RadioLink EasyTouch II ScenePoint DR Bedienungsanleitung

LEGRAND

LEGRAND DPX-IS 630 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-611MCC Bedienungsanleitung

LEGRAND

LEGRAND airQast Bedienungsanleitung

LEGRAND

LEGRAND adorne WZ3ACB40 Bedienungsanleitung

LEGRAND

LEGRAND Raritan SRC-0100 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch