LEGRAND CHIEF 25-PTS-2000 Series Bedienungsanleitung

Large Flat Panel Display Table Stand

(25-PTS 2000 Series)

The 25-PTS2000 Series for Large FlatPanel Display is an attractive pre-

sentation tool for conference rooms, boardrooms and home theaters.

The low profile of the table stand provides a non-obtrusive presenta-

tion with an adjustable viewing height

BEFORE YOU BEGIN

•Caution: To prevent damage to the 2 5 -PTS, which could affect or void the Factory warranty, and to the equipment that

will be attached to it, thoroughly study all instructions and illustrations before you begin the installation. Pay particu-

lar attention to the “Important Warnings and Precautions” on Page 1.

• •If you have any questions about this installation, contact us at 1-800-888-6024.

INSTALLATION INSTRUCTIONS

Installation Instructions PTS

IMPORTANT WARNINGS AND PRECAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: ACAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corre-

sponding instructions.

•WARNING:Improper installation can result in serious personal injury! Make sure that the structural members can

support a redundant weight factor five times the total weight of the equipment: if not, reinforce the struc-

ture before installing the 2 5-PTS.

•WARNING:Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•WARNING:The installer is responsible for verifying that the surface the 2 5-PTS is placed on will safely support the com-

bined load of all attached components or other equipment.

•WARNING:The weight of the display placed on the 2 5-PTS must not exceed 100 lbs.

(45.36 kg), the maximum load capac-

ity of the 2 5-PTS.

•WARNING:Watch for pinch points. Do not put your fingers between movable parts.

•CAUTION: Check the unit for shipping damage before you begin the installation.

NOTE: Hardware for attaching this unit to the wall is not supplied.

TOOLS REQUIRED FOR ASSEMBLY

• Phillips Head Screwdriver (#2)

• Allen Wrench Set

• Socket set with extension

• Open End Wrench Set

NOTE: Other tools may be required depending on the

method of installing the mount on the wall.

CONTENTS

INSPECT THE UNIT BEFORE INSTALLING ............ 2

25-PTS-2000 ASSEMBLY .............................................. 4

MOUNT THE DISPLAY ............................................. 6

REMOVE THE DISPLAY ........................................... 6

Installation Instructions PTS

INSPECT THE UNIT BEFORE INSTALLING

WARNING: Watch for pinch points. Do not put your fingers

between movable parts.

1.Carefully inspect the 25-PTS for shipping damage. If any damage

is apparent, call your carrier claims agent and do not continue

with the installation until the carrier has reviewed the damage.

NOTE: Read all instructions before starting installation.

2. Lay out components to ensure you have all the required parts

before proceeding (see Figure 1):

1 Base Plate with the following installed:

2 Square Bumpers

2 Hemisphere Bumpers

1 Edge Guard

1 Upright Post

1 Top Assembly

1 Face Plate

1 Latching Flag

1 Nylon Washer

1 10-24 Nylock Nut

1 Metal Mounting Bracket

1 10-24 Screw

4 Square Bumpers

1 Single Upright Spacer

2 Nylock Nut

3 Washer, .Nylon, 38” I.D.

2 Flat Washer, SAE, 3/8”

8 5/16-18 X 5/8” Button Head Cap Screws

4 5/16-18 Nylock Nuts

Installation Instructions PTS

Base Plate

Upright Post

Top Assembly

Single Upright Spacer

FIGURE 1. PARTS

Installation Instructions PTS

25-PTS-2000 ASSEMBLY

CAUTION: DO NOT attempt to mount the Flat Panel Display in

an inverted position. Mounting the Flat Panel Display

in an inverted position may cause overheating and

extensive damage to the Flat Panel Display.

Assemble the 25-PTS as follows:

1. Using four 5/16-18 X 5/8” button head cap screws and 5/16-18

Nylock nuts, secure the post assembly to the base assembly

(see Figure 3).

2. Attach latching flag to faceplate using 10-24 Phillips head

screw, Nylon washer, and Nylock nut (see Figure 4).

3. Using two washers (one Nylon .38 ID and one SAE 3/8”) and

Nylock nut, secure the top of the single upright spacer to the

top stud of the upright post (see Figure 3 and Figure 4).

4. Using two 3/8 ID Nylon spacers, two SAE 3/8” washers, and

Nylock nut, secure the bottom of the single upright spacer to

the bottom stud of the upright post (see Figure 3 and Figure 4).

FIGURE 2. POST TO BASE PLATE

Top Bottom

FIGURE 3. SINGLE UPRIGHT SPACER

Nylock Nut 3/8” Washer

3/8” Washer

Nylock Nut

Nylon Spacer Nylon Spacer

Nylon Spacer

FIGURE 4. ASSEMBLY

SWIVEL ADJUSTMENT

Installation Instructions PTS

5. At approximately the desired viewing height (4” of adjust-

ment), align the four mounting holes of the top assembly with

four mounting holes of the post assembly (see Figure 5).

6. Loosen the Nylock nuts securing the bottom of the single

upright spacer to the bottom stud of the upright post (see Fig-

ure 3), align top assembly, and tighten Nylock nuts.

7. Using four 5/16-18 X 5/8” button head cap screws, secure the

top assembly to the post assembly (see Figure 5).

FIGURE 5. BACK TO POST

Mounting

Holes

Installation Instructions PTS

FIGURE 8. RAISE LATCH

Back of Plasma PTS

Raise latch

FIGURE 7. ENGAGE Q-LATCH

Q-latch Opening

Back of Plasma

PTS

Q-latch Button

FIGURE 6. LOWER LATCH

Make sure latching flag is lowered

Installation Instructions PTS

MOUNT THE DISPLAY

1.Follow the instructions for installing the 25-PSB bracket(s) for

your specific flat panel display.

WARNING: Watch for pinch points. Do not put your fingers

between movable parts.

2. Before lifting your flat panel display, make sure the latch of the

PTS is lowered and will not interfere with mounting the display

(see Figure 6).

3. Using two people, align the Q-latch buttons with the Q-latch

openings and install the display. Make sure the buttons of the

Q-latch bracket fully engage all the Q-latch openings on the

PTS (see Figure 7).

4.Secure the display to the 25-PTS by completely engaging the latch

(see Figure 8).

5. Connect and secure power/audio/video cables.

REMOVE THE DISPLAY

1. Disconnect power/audio/video cables.

2. Disengage (lower) the latch.

3.Using two people, lift the display from the 25-PTS.

Inhaltsverzeichnis

Andere LEGRAND Rack & Stand Handbücher

LEGRAND

LEGRAND 0 570 18 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF Koncis DMA Series Bedienungsanleitung

LEGRAND

LEGRAND Chief Koncis D1U Bedienungsanleitung

LEGRAND

LEGRAND VADDIO 535-2000-280 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF IntelliSHOT PAC800E Bedienungsanleitung

LEGRAND

LEGRAND Sanus VDSF16 Bedienungsanleitung

LEGRAND

LEGRAND 2U Bedienungsanleitung

LEGRAND

LEGRAND Sanus SMF421-B1 Bedienungsanleitung

LEGRAND

LEGRAND Chief PAC800HS Bedienungsanleitung

LEGRAND

LEGRAND SANUS WSSAFM1-B2 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF Fusion FCALRB1 Bedienungsanleitung

LEGRAND

LEGRAND Chief FCA850 Bedienungsanleitung

LEGRAND

LEGRAND SANUS VDLF28 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF CSSMP15X10 Bedienungsanleitung

LEGRAND

LEGRAND SANUS ELITE BSWME2 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF OMNDBF46-55 Bedienungsanleitung

LEGRAND

LEGRAND SANUS SLF428-B1 Bedienungsanleitung

LEGRAND

LEGRAND SANUS VSTV2-B2 Bedienungsanleitung

LEGRAND

LEGRAND Sanus VDMF20 Bedienungsanleitung

LEGRAND

LEGRAND Chief OLCM1U Bedienungsanleitung

LEGRAND

LEGRAND CHIEF TIL1X2PT Bedienungsanleitung

LEGRAND

LEGRAND SANUS WSSE31 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF Fusion FCA812 Bedienungsanleitung

LEGRAND

LEGRAND CHIEF FCAVCU20 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung