Leica Disto D510 Betriebsanleitung

How to use Leica DISTO™ D510

Switch On and Off

The key switches and activates the laser in a single press.

Press once quickly to shoot a distance or...

Press and hold for 2 seconds to activate continuous laser

measurement (Tracking).

Press once quickly to switch off tracking.

Press and hold the button for 2 seconds to switch off the

E7100i. The E7100i automatically switches off after 3 minutes of

inactivity.

Display Overview of the Settings Page page

Display Overview of the Functions Page

Basic Operations

Beep On/Off

Turn the beep on/off as per your convenience.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, **Beep on/off icon / is located at the top right

of the display.

Navigate to the icon using keys to select for Beep on/off. Select

the icon using = key.

Also toggle between & with = key.

* Press to exit settings.

(**selection screen example for reference)

Digital level On/Off

Use the inbuilt digital level as and when required.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Digital level icon / is located on the middle left

of the display.

Navigate to the icon using keys to select for Digital level on/off.

Select the icon using = key.

Toggle between & with = key.

* Press to exit settings.

Display light/screen brightness

Adjust the screen brightness as required.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, (brightness adjustment) illumination icon is

located at the the bottom right of the display.

Navigate to the icon using keys to select for brightness

adjustment.

Select the icon using = key.

Once selected, use the arrow keys to increase or decrease the

brightness from the provided 6 levels.

* Press to exit settings.

Activate/de-activate keypad lock

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key

underneath the icon .

On this screen, the lock icon / is located at the centre of the

display.

Navigate to the icon using keys to select for keypad lock on/off.

Select the icon by pressing =key.

Toggle between / with =key.

* Press to exit settings.

How to unlock keypad

Once the keypad lock system is activated, the device when switched on needs to be

unlocked within 2 seconds after switching it on, or it will automatically switch off.

Press the key within 2 seconds of switching on the device to

unlock the key pad (as it will indicate on the display).

Memory

The device stores last 30 results by default.

To view the results stored in the memory, press the key once.

Navigate to the memory icon with keys, which is located on the centre left of

the display.

Select this icon using = key.

Use navigation keys to view multiple stored results.

Press the soft keys underneath icons & for deleting memory and using

the displyed value for further actions respectively.

Timer (Self trigger) or Auto release

Timer is used for self triggering the measuremnt once the laser is activated. The delayed

release is recommended for precise aiming, e.g. for long distances, as it avoids shaking of

the device while pressing the measurement key.

To set the Timer, press the key once.

Navigate to the Timer icon with keys, which is located at the top left of the

display.

On Timer selection, you reach the screen displayed as

Select the time from the provided options with the help of navigation keys.

To confirm setting press = key.

Press key once to aim the laser.

Press key again to start the timer.

Calculator

Press the key once to reach the application screen.

On this screen the Calculator icon is located at the top centre of the

display.

Navigate to the icon using keys for Calculator. Select the

icon using =key.

Reset

Reset setting returns the device to its factory settings. All customization and stored

memory is lost.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key underneath

the icon .

Move to the 2nd page of the settings with the help of keys.

On this screen, reset setting icon is loacted at the top centre of the display.

Navigate to the icon using keys to select for reset setting. Select the icon using =

key.

Use soft keys under or Xto confirm reset or cancel respectively.

Offset

Offset setting allows you to add or subtract a set value automatically to or from all

measurements.

Press the key once to reach the application screen.

Select the settings option from this screen by pressing the soft key underneath

the icon .

Move to the 2nd page of the settings with the help of keys.

On this screen, Offset setting icon is located at the top left of the display.

Navigate to icon using keys to select for offset setting. Select the icon using

=key.

Use & keys to adjust the value.

Use soft key under icon to confirm or…

Reset the value to 0.00

Advance operations

Personalized favourites

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Personalized favourites (a star shaped icon) is

loacted at the bottom centre of the display.

Navigate to the icon using keys, to select for Personalized

favourite. Select the icon using =keys.

Select your favourite functions and add them to your personal list.

Activate/de-activate Bluetooth

DISTO™ D510 includes Bluetooth® Smart (V4.0) capability that will allow it to

automatically send measurements to your tablet or phone. Check out the Leica DISTO™

App Directory to see results on your Android, iOS or Windows devices.

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Bluetooth icon / is located at the centre right of

the display.

Navigate to the icon using keys to select for Bluetooth. Select the

icon using =key.

Toggle between & using = key.

*Also Bluetooth switches off as soon as the laser distance meter is switched off.

Leica DISTO™ sketch app. is an ideal interface between the Leica DISTO™ with

Bluetooth® and a smart phone, tablet or Windows computer. This allows sketches,

photographs and Excel lists with dimensions to be created quickly. The data is

subsequently able to be sent directly to the office by e-mail.

Download the Leica DISTO™ sketch app. from:

iOS - https://itunes.apple.com/in/app/disto-sketch/id580422524?mt=8

Android - https://play.google.com/store/apps/details?id=de.ffuf.leica.sketch&hl=en

Changing distance Units

Leica Disto X510 is provided with the stock of units that you can change as per your

requirement. Change from meter to feet to inches, per your convenience.

Press the key once and you reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Distance Units icon is located at the top center of

the display.

Navigate to the icon using keys to select for Distance Units.

Select the icon using =key.

Choose from the below listed units keys.

0.00 m 0.00 ft

0.000 m 0.00 in

0.0000 m 01/32 in

0.0 mm 0’ 00” 1/32

Changing Tilt Units

You can also change the Tilt unit setting as well to measure your triangle angles.

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Tilt Units icon is located at the top left of the

display.

Navigate to the icon using keys, to select for Tilt Units.

Select the icon using =key.

Choose from the below listed units keys.

360.0 ° 0.00 %

+ 180.0° 0.0 mm/m

+ 90.0 ° 0.00 in/ft

Adjusting measuring reference/tripod

Custom your D510 to measure the distance from its front, rear, middle or the tripod

thread of the device.

1. Each time the device is switched on, the display shows the default or the standard

mode as which means that the distance is being measured from the back of the

device .

You can further change the settings by pressing under the screen to adjust the

mode to either

2. - Measurement from the front of the device,

- Lock icon = permanently

3. - Measurement from the tripod thread of the device.

How to adjust the measuring reference

Press the key once to reach the application screen.

Select the Adjust measurement application from the top right

section by pressing .

Select the icon using =key.

Choose from provided:

from the front,

back,

middle or

tripod thread of the device.

* Once the device is switched off, reference goes back to standard setting (i.e. rear of the

device)

Adjusting/Standardising/Calibration of tilt sensor (Tilt

Calibration)

Press the key once to reach the application screen.

Select the Settings option from this screen by pressing the soft key

underneath the icon .

On this screen, Tilt calibration icon is located at the bottom left of

the display.

Navigate to the icon using keys to select for Tilt calibration.

Select the icon using =key.

* Press to exit settings.

(Also)

Follow these quick 6 steps to adjust or calibrate your device in case of an unlikely

discrepancy.

As indicated on the device display:

Place the device on an absolute flat surface with its display up and press .

Next rotate it by 180° and place the device on the surface as it was and press again.

Next stand the device up on a horizontal surface and press .

As indicated rotate the device 18o°in its vertical position and press again.

Next place the device upside down as shown in the picture on the left and press .

Rotate the device again by 180° and place it on the surface and press .

*The device calibration is complete.

Basic device Applications

Straight line single distance measurement

Basic usage is quite simple.

To begin, press the key once to switch the laser on and aim at

your target.

Pressing again records the measurement and shows the result

on the device display.



* For measurements, where there is nothing obvious at the other end for the laser to reflect back, it is

recommended that you use Leica branded Target plate for maximum measurement range.

Permanent / Minimum-Maximum measurement

This function determines the minimum or maximum distance from a specific measuring

point, e.g. the determination of room diagonals (maximum value) or horizontal distance

(minimum value).

To activate permanent measuring, press and hold the key for 2

seconds. This will activate the continuous laser.

Aim the laser at wall corners (maximum value) or horizontal distance

(minimum value). The display would show the max. & min. values on

the screen.

To stop permanent/minimum-maximum measuring press key

once.

Add/ Subtract function

Add / Subtract are two basic functions in D510. The keys are

displayed on the device for this application.

Press once to add the next measurement to previous one.

Press twice to subtract the next measurement to previous one.

Point finder/View screen

Press the key on the device to activate the camera mode.

With the help of navigation keys zoom the pointfinder to 2x & 4x

zoom.

Area Measurement

Area measurement is a basic function provided in all Leica Disto devices. This helps you

calculate the area of wall or surface just by measuring its sides from the same reference

point.

For measuring the area of a surface, press the Function key once.

On this screen, the area application is located at the center of

the display.

*In D510, you can also find the area application at the bottom left of the device

as you switch it on.

Navigate to the icon using keys to select for Area

application. Select the icon using =key.

To begin, press the key once to switch the laser on and aim at

your target to take the 1st reading.

Then focusing from the same reference point take the 2nd reading by

measuring the adjacent wall length. (as the area icon will indicate on

display)

Once this process is completed the device automatically calculates

the area for you.

* Adding and subtracting areas

You can measure two separate areas and add or subtract them from each other with the

help of or keys.

**The device also calculates

The total linear distance or the circumference.

Volume Measurement

For measuring the volume of an object press the Function key

once.

On this screen, volume application is located at the bottom right

of the display.

Navigate to the icon using keys to select for Volume

application. Select the icon using =key.

Measure the three adjacent lengths (l x b x h) using . (as the volume

icon will indicate on display)

*All measurement needs to be taken from the same reference point.

Once this process is completed the device automatically calculates

the volume on the display.

*The device also calculates:

Ceiling/floor area

Wall areas

Total linear distance (circumference)

Triangular Area Measurement

For measuring the area of a triangular surface, press the Function

key once.

Move to the second page of application screen using keys.

On this screen, Triangle Area Measurement icon is located at the

top left of the display.

Navigate to the icon using keys to select for Triangle Area

Measurement application. Select the icon using =key.

Measure all three sides of a triangle aiming lasers at 1st, 2nd and 3rd

target points using as indicated , , .

Once this process is completed the device automatically calculates

the area for you.

*The device also calculates

The total linear distance or the circumference and

Angle between the 1st and 2nd measurement

Smart Horizontal Mode™

A wonderful application to measure the horizontal distance even with an obstruction in the

way.

For measuring the distance from an object through Smart Horizontal

Mode™, press the Function key once.

On this screen, Smart Horizontal application icon is located at

the middle right of the display.

Navigate to the icon using keys to select for Smart Horizontal

application. Select the icon using =key.

Aim the laser at an angle of a certain tilt and record the measurement

by pressing .

The device automatically calculates the horizontal distance from the

target.

*Along with the horizontal distance this application also records:

angle of the tilt

length of the tilt and

the vertical height from the device.

Long range Mode

The long range mode allows measuring of difficult targets in unfavourable conditions such

as bright light or extremely reflective objects.

To activate the long range mode press the Function key once.

Move to the second page of application screen using keys.

On this screen, Long range mode icon is located at the Top middle of the display.

Andere Handbücher für Disto D510

Inhaltsverzeichnis

Andere Leica Analytisches Instrument Handbücher

Leica

Leica DISTO D5 Bedienungsanleitung

Leica

Leica DISTO D810 touch Bedienungsanleitung

Leica

Leica DISTO X3 Bedienungsanleitung

Leica

Leica Disto D510 Bedienungsanleitung

Leica

Leica Disto X310 Betriebsanleitung

Leica

Leica DISTO D210 Bedienungsanleitung

Leica

Leica RANGEMASTER CRF 1600-R Bedienungsanleitung

Leica

Leica Disto X310 Bedienungsanleitung

Leica

Leica DISTO E7300 Bedienungsanleitung

Leica

Leica DISTO D810 touch Gebrauchs- und Pflegehandbuch

Leica

Leica DISTO A2 Bedienungsanleitung

Leica

Leica DISTO D5 Bedienungsanleitung

Leica

Leica DISTO D810 touch Bedienungsanleitung

Leica

Leica DISTO E7500 Bedienungsanleitung

Leica

Leica DistoX Bedienungsanleitung

Leica

Leica DISTO E7500i Bedienungsanleitung

Leica

Leica 812795b Bedienungsanleitung

Leica

Leica DISTO D810 touch Bedienungsanleitung

Leica

Leica DISTO D810 touch Bedienungsanleitung

Leica

Leica Disto D510 Bedienungsanleitung

Leica

Leica DISTO A8 Bedienungsanleitung

Leica

Leica DISTO D8 Bedienungsanleitung

Leica

Leica DISTO S910 Bedienungsanleitung

Leica

Leica DISTO X3 Bedienungsanleitung

Beliebte Analytisches Instrument Handbücher anderer Marken

Cocraft

Cocraft NLT04 Bedienungsanleitung

M&C

M&C GENTWO PMA1000 Bedienungsanleitung

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Bedienungsanleitung

CONDTROL

CONDTROL XP4 PRO Bedienungsanleitung

Extech Instruments

Extech Instruments BR200 Bedienungsanleitung

Dewetron

Dewetron DEWE-30-16 Produkthandbuch

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Montage- und Bedienungsanleitung

RIDGID

RIDGID SeeSnake Compact Bedienungsanleitung

Teledyne

Teledyne 3000PA Bedienungsanleitung

YDLIDAR

YDLIDAR TIA Bedienungsanleitung

Olympus

Olympus IPLEX FX Series Bedienungsanleitung

Bosch

Bosch GLM 50 C Professional Bedienungsanleitung

Reflecta

Reflecta DigiEndoscope Bedienungsanleitung

Chinavision

Chinavision CVACZ-G696 Montageanleitung

Fuji Electric

Fuji Electric ZKMA Bedienungsanleitung

Teledyne

Teledyne 3300TA Bedienungsanleitung

VOLTCRAFT

VOLTCRAFT IC-100HD Bedienungsanleitung

RIDGID

RIDGID micro CA-25 Bedienungsanleitung