Leica TS02 Bedienungsanleitung
Leica FlexLine
TS02/TS06/TS09
User Manual
Version 2.0
English
FlexLine, 2
Introduction
Introduction
Purchase Congratulations on the purchase of a FlexLine instrument.
This manual contains important safety directions as well as instructions for setting up
and operating the product. Refer to "13 Safety Directions" for further information.
Read carefully through the User Manual before you switch on the product.
Product
identification
The model and serial number of your product are indicated on the type plate.
Enter the model and serial number in your manual and always refer to this
information when you need to contact your agency or Leica Geosystems authorised
service workshop.
Model: _________________________________________________________
Serial No.: _________________________________________________________
Introduction FlexLine, 3
Symbols The symbols used in this manual have the following meanings:
Trademarks • Windows is a registered trademark of Microsoft Corporation.
• Bluetooth is a registered trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
Type Description
Danger Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
Warning Indicates a potentially hazardous situation or an unintended use
which, if not avoided, could result in death or serious injury.
Caution Indicates a potentially hazardous situation or an unintended use
which, if not avoided, may result in minor or moderate injury
and/or appreciable material, financial and environmental damage.
Important paragraphs which must be adhered to in practice as
they enable the product to be used in a technically correct and
efficient manner.
FlexLine, 4
Introduction
Validity of this
manual Description
General This manual applies to TS02, TS06, and TS09 instruments. Where
there are differences between the various instruments they are
clearly described.
The following symbols will identify in each section where the
instruments differ:
• for TS02.
• for TS06.
• for TS09.
Telescope •Measuring with Prism mode: When measuring distances to a
reflector with Electronic Distance Measurement (EDM) mode
"Prism", the telescope uses a wide visible red laser beam, which
emerges coaxially from the telescope's objective.
•Measuring with Non-Prism modes: Instruments that are
equipped with a reflectorless EDM additionally offer the EDM
mode "Non-Prism". When meauring distances with this EDM
mode, the telescope uses a narrow visible red laser beam, which
emerges coaxially from the telescope's objective.
Introduction FlexLine, 5
Warning
Do NOT remove the battery during operation of the
instrument, or during the shutdown procedure.
This can result in a file system error and data loss!
Always switch off the instrument by pressing the On/Off key,
and wait until the instrument has shutdown completely before
removing the battery.
TSOX_135
FlexLine, 6
Table of Contents
Table of Contents
In this manual Chapter Page
1 Description of the System 13
1.1 System Components 13
1.2 Container Contents 15
1.3 Instrument Components 17
2 User Interface 20
2.1 Keyboard 20
2.2 Screen 22
2.3 Status Icons 23
2.4 Softkeys 25
2.5 Operating Principles 26
2.6 Pointsearch 28
3 Operation 30
3.1 Instrument Setup 30
3.2 Working with the Battery 36
3.3 Data Storage 38
3.4 Main Menu 38
3.5 Q-Survey Application 40
3.6 Distance Measurements - Guidelines for Correct Results 41
Table of Contents FlexLine, 7
4 Setting 44
4.1 General Settings 44
4.2 EDM Settings 56
4.3 Communication Parameters 62
5 Tools 66
5.1 Adjust 66
5.2 Start Up Sequence 67
5.3 System Information 68
5.4 Licence Keys 70
5.5 Instrument Protection with PIN 71
5.6 Loading Software 73
6Functions 75
6.1 Overview 75
6.2 Target Offset 77
6.2.1 Overview 77
6.2.2 Cylinder Offset Subapplication 79
6.3 Hidden Point 83
6.4 Check Tie 85
6.5 EDM Tracking 87
6.6 Backsight Check 87
7Coding 89
7.1 Standard Coding 89
FlexLine, 8
Table of Contents
7.2 Quick Coding 91
8 Applications - Getting Started 93
8.1 Overview 93
8.2 Starting an Application 94
8.3 Setting the Job 95
8.4 Station Setup 97
9 Applications 99
9.1 Common Fields 99
9.2 Station Setup 100
9.2.1 Starting Station Setup 100
9.2.2 Measuring the target points 102
9.2.3 Station Setup Results 104
9.3 Surveying 108
9.4 Stakeout 110
9.5 Reference Element - Reference Line 116
9.5.1 Overview 116
9.5.2 Defining the Base Line 117
9.5.3 Defining the Reference Line 118
9.5.4 Subapplication Measure Line & Offset 121
9.5.5 Subapplication Stakeout 123
9.5.6 Subapplication Grid Stakeout 126
9.5.7 Subapplication Line Segmentation 130
9.6 Reference Element - Reference Arc 134
9.6.1 Overview 134
Table of Contents FlexLine, 9
9.6.2 Defining the Reference Arc 135
9.6.3 Subapplication Measure Line & Offset 138
9.6.4 Subapplication Stakeout 139
9.7 Tie Distance 144
9.8 Area & DTM Volume 147
9.9 Remote Height 154
9.10 Construction 156
9.10.1 Starting Construction 156
9.10.2 Layout 157
9.10.3 As Built Check 159
9.11 COGO 160
9.11.1 Starting COGO 160
9.11.2 Inverse and Traverse 161
9.11.3 Intersections 162
9.11.4 Offsets 165
9.11.5 Extension 167
9.12 Road 2D 167
9.13 Roadworks 3D 173
9.13.1 Starting Roadworks 3D 173
9.13.2 Basic Terms 175
9.13.3 Creating or Uploading Alignment Files 183
9.13.4 Subapplication Stake 186
9.13.5 Subapplication Check 189
9.13.6 Subapplication Stake Slope 191
9.13.7 Subapplication Check Slope 197
FlexLine, 10
Table of Contents
9.14 TraversePRO 199
9.14.1 Overview 199
9.14.2 Starting and Configuring TraversePRO 201
9.14.3 Measuring Traverse 204
9.14.4 Moving ahead 207
9.14.5 Closing a Traverse 210
9.15 Reference Plane 216
10 Data Management 220
10.1 File Management 220
10.2 Exporting Data 222
10.3 Importing Data 227
10.4 Working with a USB Memory Stick 231
10.5 Working with Bluetooth 233
10.6 Working with Leica FlexOffice 235
11 Check & Adjust 236
11.1 Overview 236
11.2 Preparation 237
11.3 Adjusting Line-of-Sight and Vertical Index Error 238
11.4 Adjusting the Tilting Axis Error 242
11.5 Adjusting the Circular Level of the Instrument and Tribrach 245
11.6 Inspecting the Laser Plummet of the Instrument 246
11.7 Servicing the Tripod 248
Andere Handbücher für TS02
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Leica Messgerät Handbücher
Leica
Leica Rangemaster CRF 1000 Bedienungsanleitung
Leica
Leica RANGEMASTER CRF 1200 Bedienungsanleitung
Leica
Leica LS10 Bedienungsanleitung
Leica
Leica FlexLine Bedienungsanleitung
Leica
Leica 3D Disto Bedienungsanleitung
Leica
Leica DNA03 Bedienungsanleitung
Leica
Leica Lino L2P5 Bedienungsanleitung
Leica
Leica Rod Eye 180 Bedienungsanleitung
Leica
Leica APO-SUMMICRON-SL Bedienungsanleitung
Leica
Leica DD Series Bedienungsanleitung
Leica
Leica TS12 Lite Bedienungsanleitung
Leica
Leica TS02 Bedienungsanleitung
Leica
Leica HDS7000 Bedienungsanleitung
Leica
Leica GLOW800 Bedienungsanleitung
Leica
Leica TC605 Bedienungsanleitung
Leica
Leica Nova MS60 Bedienungsanleitung
Leica
Leica TS12P Bedienungsanleitung
Leica
Leica Racer 70 Bedienungsanleitung
Leica
Leica Lino L2P5 Fehlerbehebungshandbuch
Leica
Leica Pinmaster Bedienungsanleitung
