Lexing LX-PR-65S Bedienungsanleitung
LX-PR-65S Infrared Sensor Instruction
Specifications
Summary
External passive infrared detector fully adjustable vertically and horizontally, activated by small
movements of heat.
Timer adjustable from 20sec to 12min.(reactived by the last detected movement.)
Detection range 12m with 110 degree field of view.
Override switching facility to enable permanent ON operation of light.
Light sensor adjustable to inhibit operation during daylight if required.
5. Rated load: 1000W Max.(220-240V/AC)
500W Max.(100-130V/AC)
6. Detection range: 12m with 110 degree field of view
7. Working temperature: -10~+40°C
8. Working humidity: <95℅RH
1. Power source: 220-240V/AC
100-130V/AC
2. Power frequency: 50/60Hz
3.Time setting: 20sec to 12min±2min
4. LUX night and day adjustments
Correct moving orientation
12m
123mm
76mm
100mm
Detection angle
110°
Sensor information
Planning your installation
First decide on the location bearing in mind that the detector will perform best if mounted between 2 and 2.5
meters from the ground. It is also important to remember not to position the detector where it will reach areas
such as footpaths and roads as this may result in unwanted activations from passers by.
The detector responds better when a person moves across the field of vision as opposed to straight towards
it. Mounting the detector towards the side of a building with the head angles at 45 degree will make the
detector respond better than mounting in the center looking straight ahead.
The detector cannot see through solid objects including glass so care should be taken that field of view is not
obstructed by trees bushes parked cars etc.
The detector must be mounted well clear of central heating outlets or any large reflective surfaces as this may
result in unwanted activations.
Note
Connection-wire diagram
L——brown
N——blue
L——red
Connect Land Nwith power
Connect Nand L with load.
Knob adjustment
1. TIME adjuster:
2. LUX adjuster: adjust level of light operation
20SEC 12MINS
Adjust the light delay
TIME
Night Operation Day Operation
Sensor
Brown
Blue N
L
Load
LRed
Input
Output
－＋
LUXTIME
-+
Operating instructions
Test mode
In test mode the unit will activate day or night regardless of ambient light levels. Activations during the test
mode will activate the light for 5sec. The unit will progress to AUTO mode automatically after 5 mins.
Auto mode
In auto mode the unit will activate according to the settings selected on the LUX&TIME adjusters.To allow
the unit to work only at night turn LUX to “-“ or to allow unit to operate both day&night to “+”. The amount of
time the unit stays on after activation can be adjusted from between 20sec and 12min using the TIME
adjuster.
Override mode
In override mode the light will remain permanently ON until:
a) The unit is switched OFF and ON quickly.
b) The unit has been on for more than 6 hours.
c) Dawn (light level over or about 300lux) arrives when LUX control set to “-“ position.
Nothing happen
1. Check supply to unit．
Detector clicks but does not operate
1. Check lamps are not broken.
2. Check lamps tight in lampholders.
Light go on and off quickly
1. Ensure light is not being reflected back into sensor.check for white or reflective surfaces in protection
pattern.
2. Note the detector is more sensitive in cold weather.
Light stay on
1. Check unit has not gone into Manual override mode;
2. Adjust time to minimum.
3. Ensure nothing in field of view activating detector.
4. Ensure unit is firmly fixed to a solid object with no moving branches etc. in field of view.
5. Ensure detector is not being activated by stray moving heat sources such as heating outlets cars etc.
Light switch on during storms
Adverse weather conditions and temperature changes can result in unwanted activations. This can be
minished by mounting in a protected location and adjusting sensitivity control. Switch power supply off
during storms.
Fault finding
Maintenance and repair
1.Do not attempt to repair as this could invalidate warranty or result in personal injury.
2.Clean detector lens and outside casing with damp cloth.
Sequence diagram
POWER
OFF
SELF TEST
MODE
Switch on
After 5mins
Switch off then
on once(quickly)
Switch off then
on twice(quickly)
● after 6 hours
● or power OFF-ON once(quickly)
● or at dawn (only when LUX is on
“-” position)
AUTO
MODE
OVERRIDE
MODE
Inhaltsverzeichnis
Andere Lexing Zubehör Handbücher
Lexing
Lexing LX-180GS12 Bedienungsanleitung
Lexing
Lexing LX-AL9 Bedienungsanleitung
Lexing
Lexing LX-PR-M18Z Bedienungsanleitung
Lexing
Lexing LX-PR-29A Bedienungsanleitung
Lexing
Lexing LX-MV360S2-IR Series Bedienungsanleitung
Lexing
Lexing LX-MV-360S1 Bedienungsanleitung
Lexing
Lexing LX-PR-28F Bedienungsanleitung
Lexing
Lexing LX-PR-S15-Z Bedienungsanleitung
Lexing
Lexing LX-MV-360S13B Bedienungsanleitung
Lexing
Lexing LX-MV-360S15A-Z Bedienungsanleitung
Lexing
Lexing LX-MV-360S2-A-Z Bedienungsanleitung
Lexing
Lexing LX-MV-360S15B-Z Bedienungsanleitung
Lexing
Lexing LX16C Bedienungsanleitung
Lexing
Lexing LX-SLL136L Bedienungsanleitung
Lexing
Lexing LX-PR136A Bedienungsanleitung
Lexing
Lexing LX-MV-360S13A Bedienungsanleitung
Lexing
Lexing LX-MV-360S18 Bedienungsanleitung
Lexing
Lexing LX16C-Z Bedienungsanleitung
Lexing
Lexing -MV-128LED-D Bedienungsanleitung
Lexing
Lexing LX-PR-29B Bedienungsanleitung
